Making New Feet and Rails for an Antique French Bed - Thomas Johnson Antique Furniture Restoration

Thomas Johnson Antique Furniture Restoration
41 followers
2 Video Views·Aug 14, 2015
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine fashions a queen-size bed from a double-size antique footboard and headboard, raising its height with newly turned feet, and extending its length with custom bed rails. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, call us at (207) 222-2266, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
I'm Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorman, Maine.
This is a very nice headboard and footboard. It's French. I'm not sure which style. I know
it's French because it's stamped with the name of the manufacturer and their address in Paris.
I'm thinking possibly it's an early 20th century reproduction.
What's going to happen here is the owners want the bed raised up. The original height of the
rails was very low. So we're going to raise it up four and a half inches and then I'm going to make
new bed rails long enough for a queen size bed. I think the first thing I'm going to do
is remove one of the legs just to see exactly what I've got there.
Okay the foot came off fine. So I have turned four identical legs here. As you can see I've
already put flutes in two of them. What I did was I made this jig which is a box made out of plywood
that I can fit over the leg that I've turned here. I've remounted it on the lathe. Now I will adjust
my jig exactly where I want it and I'll use a small air-powered router then to make the actual
flute. Okay I've got the box clamped into position now. I lock the lathe into position using the
index and then I'll make my first cut here a light cut. Okay so now I'm going to trim off this
waste piece. I'll leave the bottom on for now so give me a way to stamp them up. I'm going to sand
the flutes and stain these and get them ready for a finish. There's a lot of different colors
in the footboard and headboard but I'm going to concentrate mostly on the color that's on this
upper column because my pieces match that. I fooled around with a piece of wood that I have
from the same stock that I turned the legs with. I mixed together some walnut stain and some golden
oak stain. It looks a lot lighter there. The leg that I stained though, because it's a turning,
came out darker. I'm still glad that the leg is lighter. I'm going to use this stain and then I'll
seal it with shellac and then I have a couple of other techniques with other stains I'll use to
darken it. Now I'll brush on the first two coats of shellac. So I've let the shellac dry overnight.
Now I'm going to sand them with 320 and then I'm going to stain them again either with an oil
stain or glaze to see if I can bring it in to the footboard. So now I've got them all sanded
and I'm going to apply the glaze coat. Glaze is a heavy medium. I don't know exactly what it's made
out of with colors added. In this particular case, I buy the glaze already mixed up with Van Dyke
brown in it. You can control the glaze, that's why you put it over a sealed surface. Just as a
demonstration, I'll put some on my sample piece. You apply the glaze. You can wipe off as much or as
little as you want. So I'll very carefully just pat it a little bit. I'll leave a little bit more
on this side. Then I take a dry brush. I'm leaving a little bit more on this side so it'll be darker.
So I'll apply the glaze liberally because I want it to get down into all the crevices and corners
and I'm just patting it off. Now I want to leave some down these corners and crevices and whatnot
but not too much. The part that's left over in the crevices and corners and stuff is a little
darker and that gives it more depth. My foot here is a little light. I definitely don't want the
foot to be lighter. Feet are always darker. Yeah, I like the way it looks. It looks good with the other
upper part of the column. Now that's very much kind of laying on the surface. It needs to dry
really well. If you're going to brush on the finish, maybe dry overnight. I'm going to spray
these with the aerosol lacquer and so I need to let it dry for just an hour. I made a little jig
here. Just a square piece of wood. I drilled a half inch hole on the drill press attached just
to the back. I can clamp it here to line up exactly where I need to drill.
This is a dowel sizer. It'll help me size the dowel I turned on the leg.
By changing the angle of the clamp, I'm just trying to get that to go on straight.
The next step is to make new rails for the bed. This bed didn't come with any rails.
It doesn't matter anyway, although it wouldn't be nice to know what they look like.
I think it's pretty straightforward. We need to make new rails in any case because we're
making this bed into a queen size bed. So I'll cut these boards and build up long enough for a queen.
So I've cut my rails to length and I need to drill into the ends. I'm going to put two dowels
and then a hole for a bed bolt. I cut an extra piece when I was cross-cutting them
of the rail about two inches wide and on the drill press I drilled the holes exactly where
I wanted them and attached this so I can attach it to the rail. The center hole is for the bolt.
This is the bed bolt that's going to go through the headboard and footboard and I'm going to embed
the nut into the rail. So the first step is to drill that center hole deep enough to go to the
two different moldings on the bed where the right here where the rail attaches.
There's two different moldings that run along the bottom and the top of the rail so I've got
to reproduce those. Now I've drilled all the rails and installed the bed bolts. I did one section of
the bed where the rails connect and now I've got to do the other three parts of these legs where
the rails connect. The center hole is for the bolt so I've got to drill that now all the way through.
What I'm going to do is I'm going to clamp a piece of scrap wood underneath so that when the
bit breaks through the other side it's clean. Now I've got my half inch hole which can accommodate
the bolt itself but I'm going to need to drill from this side a 7-8 hole to accommodate the head
of the bolt. So the first thing I'm going to do is plug this hole with a half inch dowel so I can
drill. So here's my plugged hole and now I've got to drill a 7-8 hole to accommodate the head
of the bolt. So I'm going to go down. I'm going to go down one inch right here. I'm going to clamp
a block of wood to the side. The bit gets so close to the edge here that I want to ensure that I
don't get any breakout or anything. Now the bolt fits right in there and I've got room for a cover.
Now comes the moment of truth when I put the bed together with the new rails for the first time.
I'm going to put it together and then I'm going to attach the moldings to the outside of the rail
because I've got to line them up exactly with the existing moldings on the bed.
Now while the bed is assembled and the nuts I know are in place and positioned
where they need to be, I cut some little pieces of wood and I'm going to glue that in there.
I'll flush it off and sand it later to capture the nut in place. I've sanded up my moldings here
and now I want to locate them while the rails are still attached to the bed. I think what I'll do is
I'll clamp the moldings in place and then I'll just draw a line and then I can
take the bed apart and glue in the moldings.
So now I'm going to trim off the ends so that they're nice and flush
and then I've already sanded everything but I'm going to go over everything again with 150.
I'm staining the rails now with some oil stain, some brown, some gold oak and thinner.
So here's the bed set up in a customer's home. If you remember when they bought it it was just a
headboard and a footboard. It was much lower to the ground so I made new legs that raised the
height four and a half inches and it had no bed rails. Also it was made for a 54 inch bed so I
made new rails and I was able to move them far enough to the outside edge of the bed that it
can now accommodate a 60 inch mattress. And the bed is put together with bed bolts. There it is.
I think it looks pretty good.
