Highline Leashes 102 - Installing and Tying In

HowNOT2
100 followers
1 Video View·Jan 7, 2017
How to install your leash and how to tie into it. Don't use a carabiner to connect yourself to a highline!
Check out the Accident and Injury Report from the ISA at.... http://slacklineinternational.org/wp-content/uploads/2016/11/Accident-and-Injury-Report-2015-Final-EN.pdf
How do you install the leash and how do you tie in?
Check it out in this episode of How Not to Highline.
I'm Ryan Jinks and welcome to my garage.
Today we're gonna go into how to install a leash
and how to tie into it.
In case you've never seen a highline
or a video with a highline in it,
the first thing you need to know about installing the leash
is that it goes on both the main line and the backup line.
Hey, keeping it basic,
I didn't know when I rigged my first line.
So a useful tip is to actually put the leash on the webbing
when you're at home.
In fact, you should get your entire rig set up
and flaked into a bag at home.
When you do that, you're gonna wanna figure out
what side of the highline you're gonna want your leash on.
Is the person on the far side gonna slide over
after it's all rigged?
Or would you rather have it on the tension side
after it's all set up?
And sometimes it's more convenient
to install two leashes on your highline,
especially the longer they get.
This might be an obvious tip,
but don't forget to put the leash on
before installing the webbing and the web locks.
I know it seems obvious,
but I forget to put the leash on before the web locks
more than half the time.
In fact, I forgot to put it on
when I set up for the scene.
Damn it.
If you are gonna send the leash over to the far side
so your partner can slide over when they're done,
make sure you clip it to something
so they can reach it
after they're done pulling the tagline.
Instead of tying it to the end,
it's nice to have a separate veneer
so they can clip it to something out of their way
while they're managing all of this.
And if you wanna keep the leash on the tension side
while you slide the webbing over,
clip it to somewhere on the anchor
so as the webbing slides through,
the leash stays on your side.
And when you're done highlining
and you untie from the leash,
make sure you tie the tail off to something at the anchor
so the leash doesn't just slide down
to the middle of the highline.
So now it's time to tie in,
and there's only five steps you need to know.
Good luck remembering five separate things
when you're stoked to get on a highline.
Guess where almost every highline leash is?
Near the cliff edge.
So step one is to have a built-in personal anchor
on an auto-locker so you're safe
while tying into your leash.
So step two is to grab the leash and check for twists.
The last person who walked turned around a lot
or they fell and spun a lot,
then your leash could be twisted.
The problem with a twist in your leash
is not only is it kinked while you walk,
but in something like that you can get your finger,
your arm, your neck, your leg,
or your dick if you're doing a naked send.
The two most common injuries on a highline
are probably falling near a cliff edge
and hitting the cliff,
or getting something caught in your leash.
Step three is to check the knot at the ring.
You wanna make sure that it's a figure eight,
and you wanna make sure that it's not rock hard
so it retains most of its strength.
So massage it a little bit and make sure that it looks safe.
Step four is to measure it.
If you tie in too short,
you won't be able to stand up all the way
and you'll be highlining like this, which is hard.
And if you tie in too long,
you're gonna have further to fall,
which makes for a harder fall,
and more leash to climb back up
when it's time to climb the leash.
So if you walk with the leash on the outside,
you're gonna need a longer leash.
If you walk with the leash between your legs,
it doesn't need to be as long.
So lately I find that I like tying in shorter
because on looser lines you tend to have steeper sections
and it doesn't hit the back of my foot as much.
But if you're gonna do a double backflip,
by all means, make it as long as possible.
A non-exact science way of doing it
is to stick this arm out
and to put your elbow against your stomach,
and this is where you want your first half of the figure eight.
You can find your own way of measuring a leash
because they all come pretty standard in length.
One way I don't recommend to measure your leash
is to stand up and put your foot there
to see how far you want it.
I don't recommend that
because you're standing near a cliff edge.
Even clipped in, if you fall near a cliff edge,
you'll probably hit the cliff.
So find your own way of measuring your leash
without doing this near a cliff edge.
So your fifth step is to tie your figure eight.
Start by making half of a figure eight.
You twist it, you go around the rope
and back through towards yourself, creating a figure eight.
If you didn't go around enough times,
it'll look like an overhand knot.
Then you put the tail through the bottom
and the top loops of your harness,
which I can't believe I'm going over
because if you don't know that,
you shouldn't be highlining.
Pull the half of figure eight all the way to your harness
and take the tail and trace the original knot.
The end comes out there, so the tail will go there.
It goes around, I go around.
It goes through, I go through.
It goes around, I go around.
And then finally, comes out the top.
You'll know if you measured it right
based on how much tail you still have.
Create your backup knot.
You're gonna spin around the leash with the tail,
downward, and then the loop it creates,
you put the tail up towards the top again.
If there was a sixth step, it would be to check yourself.
Make sure that your harness is double backed
if it's not automatically double backed.
Make sure you're going through two points of your harness.
Make sure that your knot isn't way up here
and only about a fist away from your harness.
And then check to make sure your knot is right
by counting parallel lines.
Two, four, six, eight, 10, with a backup.
Then have your partner check it all over again.
Why is checking this so important?
Because you're only gonna tie in once.
And if you **** it up, you're gonna die.
And lastly, you can unclip
from the pre-installed personal anchor.
And now I'm all set to highline.
So let's talk about how not to tie in.
Which brings us to our next feature
of learning from other people's mistakes.
At my first Highline Festival,
someone did not finish tying their figure eight.
They got to here and then got distracted
decided to go out on the highline and then fell.
I don't know how this held them, but it did.
And there were a lot of people over there.
How did they get on the highline?
And nobody saw that.
Another incident was at Uphill 70 Falls.
Someone scooted out three or four scoots
out on the highline and realized
they never tied in at all.
How could that happen, you ask?
Well, when you're super stoked about something
and nobody's there to check you,
shit like that could happen.
Luckily they realized it,
freaked out and scooted back.
And on the International Slackline Association's
incident report, someone only put it
through the lower portion of their harness.
And when they fell on it,
it undid the automatic double backing
leaving them hanging by their knees.
Their incident report published in November 2016
said there were 13 leash and harness related whoopsies.
So the moral of the story is to take
tying your leash very serious.
Forgetting to install your leash
can be a real pain in the ass.
And there's about five ways to screw up on tying in.
Therefore, you shouldn't highline.
Hey, don't be a dummy and go do dangerous boards
after watching a guy in his garage tell you how to do it.
But make sure you go with an expert
the first few times you go highline.
In the meantime, check out these other videos
and don't forget to subscribe.
Thanks for watching and please be safe.
