606. Trimming 3 Moon Jar Bottles on a Chuck with Hsin-Chuen Lin 林新春 天球瓶修坯示範

Hsinchuen Lin
205 followers
5 Video Views·Aug 16, 2021
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
http://www.etsy.com/shop/hsinceramics
http://www.etsy.com/shop/hsintools
http://www.etsy.com/shop/potterysquare
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook page: Hsin-Chuen Lin Ceramics
Alright, so I am ready to trim this moon jar shape bottle.
For the opening, this kind of small opening, you need to have a chuck to hold it on the
shoulder of the bottle to be able to trim.
So I have a chuck here, and this chuck has been a best buyer.
I soaked it in water a bit so it will be easier for me to use the clay to anchor it down.
So first I will roughly center it, and then place my bottle on the chuck.
You could do this, if your pot is getting a little bump, you could put the clay here
to hold it, or put the clay in between the chuck and the pot.
Actually, by doing so, it's easier for you to adjust when you try to level your pot.
How do you level it?
The easiest way is that you find this little bubble leveler.
It's easy to find, you could go to a hardware store or even amazon.com, they have it.
So having the clay underneath of that, it's easier for you to just squeeze it and push
it and make sure the bubble is in the center.
So I turn it and see if the bubble is in the center.
Okay, so that looks good.
And then after that, I want to make sure that the clay is anchored down on the chuck.
So, let me put in more clay to hold it.
Like I told you in my previous video, if you want the clay to be able to stick on your
chuck easier, put the chuck in the water for 15, maybe even 20 minutes, 30 minutes,
until it's not absorbing water anymore.
Okay, so the pot is staying on top of the chuck.
And by now, the chuck is still movable, because first I want to level it, and then after you
level it, you could center it.
If you don't know how to center it, how to tap center it, you can use a needle tool to
check, right?
Put the needle there and see which spot is off, and then you move to the center.
Okay, and you keep on doing it until you can draw the whole circle around it.
Okay, so that's for basics.
If you don't know how to tap center, since I know how to tap center, it's even easier
for me just by tapping the chuck.
Right, and at the center, you can now use a clay tool to hold down the chuck.
Okay, all right, so that's the centering.
And then I'm going to use, again, my carbide tool to do the trimming, and use the larger
one.
This is the larger one for the general surface trimming here.
And then for the detail cutting the foot, using my...
Actually, this is not a carbide, okay?
This is steel.
It's the stainless steel.
I am developing another tool for the detail trimming.
This is my prototype.
It's the stainless steel, but I'm going to turn it into a carbide.
Okay, and that is removable again.
Okay, so that's my prototype.
So I will use both to show you the trimming process.
Right, so this tool, you can hold the tool, use the thumb and the finger directly, and
then get your index finger to hold it to stabilize the tool.
Right, so I did the roughly trimming using this one, the larger one.
People call it a teardrop, shaped like a teardrop.
And then I'm bringing my square tool to get the corner a bit better.
Okay, so I don't know if you can tell.
This sounds about right, the thickness of the bottom here.
So I am going to stop, keep on digging and just try to finish it a bit better.
Right, so this is the foot trimming.
I was using three of my trimming tools.
For rough trimming, use this one, and then for cutting the foot.
But finally, I was using my number two to get a corner a little bit better.
A little bit better here.
Right, and then if you wanted to, in my case, I usually do.
I turn it upside down and then trim a little bit further here for the shoulder
so that the curve follows through a bit better.
Right, so that's the trimming for the two pounds of moon jar.
And let me wait.
So let's wait after trimming to see how much clay I've removed.
So it's a pound and five ounces.
So I removed around 11, not quite 11, 11 ounces.
So that's pretty light after trimming.
So this is the smallest one, and I will go ahead and do the rest of it.
Three pounds of clay, so after trimming, a pound and 14 ounces.
Right, so this one after trimming is three pounds of clay.
So it was five, so I removed two pounds of clay.
Right, so that's trimming of three different sizes of moon jar-shaped bottle.
Okay, thanks for watching.
I might have put some slip and do a little bit of chattering and scruffy carving for the decoration.
Maybe show you in another video.
So this is the trimming of three different sizes of moon jar-shaped bottle.
Right, see you next time.
