MaxxAir vent cover install DIY for RV's And Motorhomes

C.L.S. All-IN-ONE
129 followers
8 Video Views·Dec 9, 2022
Hey everyone, this is CLS on 1 and today we're going to be installing some Maxxair vent covers
for your existing roof vents on your RV or motorhome. And these go right over the top
of your existing roof vents and these work great for ventilation and protecting your roof vents.
The vent covers are designed to be installed to where the tapered end goes towards the front of
the vehicle. There is some drilling involved but you don't drill into your roof, you drill into
your existing roof vents. My favorite thing about these vent covers is it gives you the ability to
open your roof vents even while you're driving. But you do want to be careful if you plan on
installing one of these vent covers over the top of an existing roof vent that has a built-in fan.
You want to make sure that you get the proper vent cover because if it doesn't have enough
ventilation the fan could overheat and possibly start a fire. So check with your local RV dealership
to make sure which vent cover is right for you. So the tools we need is a drill with a phillips head
screw bit, a 316 drill bit, a pencil, an adjustable wrench, or pliers. So you install the cover with
four brackets, two on each side. And here's a look at one that's already finished just so you can
see how the brackets go on. And again like I said there is no drilling into the roof itself, you
drill into the roof vent. And here's an up close look at the bracket and the slots give you a lot
of room for adjustment. So I'm going to start by placing these against the side of my roof vent.
So I'm going to put one towards the front and one at the back and space them about 10 inches apart.
Now I'm going to drop my vent cover down in place and line it up with my brackets.
And I got lucky my brackets are already pretty close to where they need to be but more than
likely you're going to have to adjust where the brackets are so they line up with the holes on
your vent cover. So just slide those brackets to where they line up with your holes. Once your
brackets are in position go ahead and remove that vent cover and mark where your brackets are with
pencil. And your brackets should be in the same position on the opposite side. If for some reason
they're not you're going to have to adjust your brackets and realign everything. Now it's time
to drill a hole at the top of that bracket through your roof vent. Now it's time to attach the
hardware. So we're going to take this bigger bolt and that's going to attach to the bottom of the
bracket. We're just going to place it in there. Then the smaller bolt nut is going to attach to
the top and that's what's going to secure it to the roof vent. So this is how it should look when
your bolts are in position. And now I need to put the nut on the other side of this smaller bolt
on the inside of the roof vent. And to tighten it I'm going to hold that nut with a pair of pliers
on the inside of the roof vent and then use my drill on the outside to tighten it. If you don't
have enough room for your drill you might just have to use a phillips head screwdriver. Now you
just want to repeat that procedure for the remaining three brackets. So I got four brackets installed
and they're all square with each other. Now it's time to attach the vent cover to your brackets.
So we're going to slide that down position over the top of the bolts that are sticking up.
Now it's time to attach the lock washer followed by the nut. And you just want to hand tight those
nuts to start with. Once you have all that hardware in place and all those nuts hand tightened go ahead
and go back over it with an adjustable wrench, a pair of pliers, or a ratchet like I have. But you
want to make sure not to over tighten it. You just want to get it nice and snug. Otherwise you could
break that plastic. Okay we're all done here's a look at it. There's not a whole lot to install
on these but hopefully this can help you out if you're trying to install a set of these.
I'm really a big fan of these. I've had these on a couple motorhomes and RVs and
I really like them. Alright guys thanks for watching. If you like this video please click
that like button. And if you want to hear more from me please subscribe. And if you
want to see more of my videos just click any of these links.
