How to install Grab Bar inside Tile Shower. D.I.Y. Home Depot materials

C.L.S. All-IN-ONE
129 followers
136 Video Views·Dec 10, 2022
Hey what's up everybody this is CLS all-in-one and today I got another how-to video for you.
I'm going to show you how to install a grab bar or a handicap bar inside of a tile shower.
The grab bar I'm installing today is made by Glacier Bay and this is 24 inches long
and these do come in various different sizes and this particular grab bar
is ADA compliant so it does work great for handicap access.
Installing a grab bar in a tile shower can be a little bit difficult and there's a lot
of different things that can go wrong including damaging your tiles.
I'm going to show you some tips and tricks today to help you install these grab bars
and do it right the first time.
So there's multiple different ways we can secure the grab bars to the tile shower
including a lot of different anchor options out there but I highly recommend securing
your grab bars to a stud whenever you can because it's going to be a much stronger support.
And if you're going to be using this for a handicap access bar
you want this bar to be as strong as it can possibly be.
To locate where the studs are I'm going to go to the back side of the shower wall
then use a stud finder to figure out where all the studs are located.
For this shower wall it's fairly simple to access the back side of this wall
because I just have to look around the corner.
But a lot of times the back side of the shower wall might be inside of a closet or a bedroom
it just depends on the layout of your house.
But no matter where the back side of your shower wall is located
you should be able to make a measurement from an adjacent corner
to figure out where the stud location is.
And if for some reason you can't access the back side of that shower wall
to locate those studs with a stud finder
you could buy an enhanced stud finder that has the capabilities of reading through tile.
But these types of stud finders can be a little pricey
and for this job an enhanced stud finder is not required
and I can just use just a regular old stud finder.
So what I've done here is I've made a mark on the wall where the first stud is located.
Now I'm going to use a tape measure and measure from the mark on the wall to the edge of the wall
and that looks to be about 13 and a quarter.
Now I'm going to go to the other side of the wall where the shower is located
and measure from that same edge and measure 13 and a quarter inches over.
And that will be the location of where the stud is inside the wall.
There's also a stud that's located in the corner of this wall
where I could easily mount that grab bar.
But for this job the customer does want that grab bar a little bit inside the shower
so 13 and a quarter should work out pretty well.
Now for the opposite side of this shower I'm also going to be installing a grab bar
and I'm going to have to find the stud location for this side as well.
On this side I'm going to use a slightly different method.
This wall is an exterior wall on the house so the studs inside this wall should be every 16 inches.
So what I'm going to do is use a stud finder to find a stud on the outside of the shower here
then measure over 16 inches to find the next stud then 32 inches and so on.
So I've made a mark here on the sheetrock where the stud is located on the outside of the shower.
Now I'm going to measure over 16 inches to the inside of the shower
and make a mark at the first stud location.
Then make a mark at 32 inches for this second stud location.
And now I have two possibilities where I can mount the grab bars to a solid stud
that's located behind the tile.
After marking all your stud locations on the tile
you want to make sure that you're going to be clear of any plumbing fixtures.
You want to make sure that when you drill a hole in the wall
that you're not going to hit any of your plumbing pipes.
So please double check and make sure none of these locations line up with your plumbing.
And if for some reason they do line up with your plumbing
you're going to have to find a different stud location.
So I've determined that my stud location is just fine and I'm going to continue on.
For this job I will be mounting the grab bars in a vertical position.
For the desired height that's really a preference that's up to you.
But for these bars I will be mounting these at 48 inches at the top.
So what I've done here is made some cross marks on the tile wall
where the stud is located centered at 48 inches.
Then I marked the top hole on the grab bar where it secures with a screw.
And now it's time to drill a hole where I just marked.
To drill this hole I will be using a specialty bit made by Bosch that measures 3 16ths.
And I'll make sure to post a link to this bit down below.
I also recommend to have a spray bottle of water handy to spray that bit off as we're drilling.
That way that bit doesn't get too hot and possibly crack that tile.
And you're also going to need either a hammer drill or a drill that has a hammer drill setting.
And what I like to do at first when drilling in a tile is start off
really slow with the drill and just make a little bit of an indent in the tile with that drill bit.
And what this is going to do is give you a guide hole to keep that drill bit in place.
If you were to just start off drilling really fast at first
you might end up slipping on the tile a little bit with that drill bit and drilling in the wrong place.
And as I'm drilling I do like to spray that bit off with water and spray the hole at the same time
to keep everything nice and cool and make sure that tile doesn't get too hot and possibly crack.
And all we're looking to do with this drill bit is get through that tile and any possible
creep board that might be behind it. Once we get through that we can go ahead and stop
then use a different drill bit to finish the job.
You also want to make sure the hole you drill is slightly larger than the screws you're going to
use because if the hole is too small when you go to screw through that tile it could chip it and
cause damage. And now I've switched drill bits to a regular wood drill bit and I'm going to finish
drilling through the stud. And with this drill bit it does need to be just slightly smaller than the
screw that you're going to use. And by doing it this way that screw was secured to the stud with
a nice and strong bond. So once again what you want to do is use a oversized drill bit to get
through the tile then stop at the stud. Then finish drilling through the stud with a slightly
undersized drill bit. And to start off with I'm only going to secure this bar with one screw at
the top until I get at least one screw at the bottom. That way I can make sure my bar is nice
and plumb and I have it in the correct position. And here's a tip for you if you have some covers
on your grab bar that look like this. These are meant to hide the screws but these covers can get
in the way while you're trying to install the bar. So what I've done here is I put a piece of tape in
the middle of the bar and that keeps these up and out of the way until I'm ready to put these in
place. Now it's time to mark a hole on the bottom of the grab bar and get it drilled. And if you
want to you could just use the grab bar as a guide and leave it in place as you're drilling. Or you
could just move that grab bar to the side and drill it like you did the first hole. But keep in mind if
you're going to drill it like I am right here with that grab bar remaining on the wall you're going
to want to be careful and make sure that drill does not cause any damage to your grab bar as
you're drilling because it's going to get really close. And if you wanted to you could even put
some masking tape on the grab bar to help protect that finish while you're drilling. So I've made it
through the tile now with my oversized tile drill bit and now it's time to switch bits back to the
wood one and we'll finish drilling through the stud. And once I finish drilling this hole I'm
going to go ahead and add another screw at the bottom here to secure the bar in place.
And now the bar is perfectly in place but we're going to have to add some more screws. So I'm
going to add one on each side of the bottom and top. And we have to drill these at a diagonal
angle that way it reaches the stud. And again if it's easier for you just to mark the holes then
remove the bar then drill them you can do it that way. But I'm just going to keep this bar in place
and keep drilling. So because the stud in the wall is only an inch and a half wide
only certain holes on the grab bar will line up. That's also why I have to drill these in an angle
otherwise these screws will not reach the stud that's in the wall. And I would recommend to get
at least two screws on the top and bottom and if you can get more that's even better. Now it's time
to go ahead and remove all the screws that I just got in place and remove the bar from the wall.
And as soon as you have that bar removed it's time to add some sealant to the holes.
And all I'm going to use is some clear silicone. So we're going to put some clear silicone in each
one of these holes and this is just some bathroom rated 100% silicone. So we're going to fill these
holes up and make sure you get a good amount squeezed inside these holes. We want to make
sure we have a nice and good seal with the screws and make sure no water can get through these
screws and back behind the wall. And now I'm going to also add a bead of silicone to the inside edge
of my bars here. That way my bar has a nice strong seal against the wall. And now it's time to
install the grab bar back on the wall. And you're going to want to be careful not to make a mess with
all that silicone. I'm going to go ahead and get all our screws in place and just put these in place
by hand to start off with. Then go ahead and drill them in one by one. And after getting all those
screws in place and getting that bar secured it's time to go ahead and put those covers in place.
And these just snap on or press on really easily. They got a couple notches that line up with some
of the flanges on the outside edge of the bar here and you just pop these right in place. And here's
what the finished product looks like. These bars are super sturdy because they're secured to those
studs inside the wall and I don't have to worry about these bars coming loose. These bars are
going to stay on for a long long time. So this method works great if you're mounting the grab bars
in a vertical position. But you could also use this same method and mount the bars in a diagonal
position like this. In this picture where the two red lines are is where the studs are located behind
the tile wall. And because of the distance between the studs only being 16 inches and the grab bars
being 24 inches I did have to mount these at an angle. But I was able to secure this to two
different studs inside the wall and get this bar nice and solid. Okay well hopefully you're on the
right track now to install a grab bar inside your tile shower. Hey everyone thanks for watching this
is CLSO1. If you want to hear more from me please like and subscribe. And to see more of my videos
click any of these categories to see more.
