5 BETTER FRAMING Options!

Matt Risinger
48 followers
4 Video ViewsยทDec 6, 2022
5 BETTER FRAMING Options!
How could you upgrade the worst built home in America?
Now, if you haven't watched my last video,
press pause here real quick and go watch the last video I published.
I'll put a link in the description.
We went and toured a house under construction by a production builder that is
code legal, but is absolutely terrible, just terrible construction.
And there's a few things that could be substituted product wise and methods
wise. Let's say that would make the performance go up exponentially.
And really wouldn't cost that much more. So in the build show today,
we're going to explore five wall assemblies,
traditional stick building really not much different than what you saw on that
job site,
but swapping some materials and some methods to much higher performance.
Today's build show all about fixing the worst build house in America.
Let's get going. All right guys. So first off,
let's talk about what we saw at that job site.
That was two by four construction with a cardboard sheathing on the outside.
And then ultimately a standard fiberglass R13 bat.
Now I say that's code legal, but it's not code legal everywhere in the U S and
you need to figure out which IECC international energy conservation code cycle
you're under. But currently where I am, we're under the 2015 codes.
And that says that in climate zones one or two,
you can build a standard two by four wall with R13 cavity insulation and you're
legal. And that's what we saw at that house.
So that is legal per code in terms of insulation requirement.
Now I would venture to guess that if they had a blower door test,
they would not meet their air tightness requirements.
Although that's not being enforced in many jurisdictions of the U S yet it's
going to be. And as we publish this video,
my hope is that you're interested in building, not just a code legal house,
but at least that or better. Okay.
So a two by four wall that's actually legal to build in all climate zones.
You can build a house that will meet insulation requirements with just a two by
four everywhere. But if you look at this requirement,
as you get into zone three,
you either need to put R20 in your cavity meeting.
Now you've got a frame of the two by six wall,
or you need to go R13 plus a number. And when you see a plus,
that means exterior insulation. That's either something like this,
which is zip R that has insulation bonded to the sheathing or that's rock wool
comfort bat on the outside or poly ISO or XPS or some other type of sheet
insulation installed on the outside of the house.
So even in the very coldest climate,
Alaska is a mix between climate zone seven and eight.
You can build a two by four wall.
You just need R10 on the outside,
or you can build with two by sixes and you need an R5 on the outside.
So back to our original question,
how do we upgrade America's worst built home that I was in the other day?
The easiest way to do that is this right here.
We're going to go ahead and swap out that cardboard sheeting for OSB sheathing.
This is going to be the least cost way to sheathe your house and then put a
standard mechanically attached house wrap Tyvek,
basically a white house wrap that you're going to hammer tack a staple on to
hold on. This is going to be a much, much better house.
It's going to give it much better rack strength.
It also means that we're going to have to now force our trades to drill through
and make a clean hole that we can actually air seal later.
And when we put a house wrap on the outside,
instead of that cardboard sheeting,
we can use much better products to waterproof the house because water is the
number one enemy to durability. And if you saw that house,
there was all kinds of penetrations that were done poorly, including windows.
They were using a standard vis queen, a black vis queen,
which is plastic basically for a sill pan for the windows.
And if you look in the corners,
there's a bunch of cuts in those corners because it's not a flexible material,
which means that those corners are vulnerable. If water would get in there.
And anytime they penetrated with wires or pipes,
it's really hard to air seal. When you're using that cardboard sheeting,
when we go to plywood or OSB or a solid sheathing,
and then put a mechanically attached house wrap so much better.
So that's number one. Now let's talk about cost.
I promised in the last video that I would show you some costs in today's
environment, materials have gone up quite a bit.
And so remember that depending on when you're watching this video,
these costs are going to vary. But even six months ago,
a lot of these materials were cheaper today in my town.
If I were to buy a sheet of that cardboard sheathing, it's around nine bucks.
OSB is about double or slightly more that cost around $20.
And again, that's going to vary depending where you are in the U S but $20 for a
sheet of OSB. House wrap like Tyvek,
if I were to buy that on let's say the Lowe's website is running about 13
cents per square foot, one square foot of that.
So I'm going to try and break down my costs as I talk about these wall
assemblies per square foot of wall.
And this is inclusive of the two by four, the sheathing,
and whatever type of WRB weather resistant barrier house wrap we're
using. So this first wall assembly,
the one that's the worst build house in America,
I'm estimating that house costing about a dollar 62 per
wall square foot in upgrading to this assembly that I think is a better
assembly with OSB and house wrap.
We're talking about $2 and 18 cents per square foot.
So that's a 35% increase just in wall costs. Remember,
we're not changing the slab. We're not changing the roof, other things.
That's just per square foot of wall. So it is a little bit more,
but I would say that labor is not going to increase a whole lot more,
but let's also look at effective versus nominal R values.
When I say nominal R value,
what I mean is when you look at that bag of let's say Rockwell insulation,
it's going to say R whatever on there, R15,
let's say for a two by four high density Rockwell bat.
When we talk about that wall, we often as builders say, Oh,
that's an R13 wall.
But in fact,
the nominal R value is different than the effective R value.
The effective R value takes into account the two by four studs,
the headers, the double top plate, the windows, all that sort of thing.
Now I'm going to leave off the windows for now,
just thinking about a section of wall that includes two by fours.
We think that's R13 on that first example, but in fact,
the opaque assembly is really 10.526 per an
online calculator that we found. It's a pretty good one, by the way,
I'll put a link in the description. Now this next assembly,
when we swap out that OSB,
it's actually slightly better because wood does have some insulation value and
half inch OSB according to that calculator is like R.6.
So we're talking about an 11.11 effective R value of
that wall assembly. Now let's upgrade that a little bit.
Let's go to an R15 insulation and let's upgrade our sheathing
from standard OSB or plywood to something like this.
Now this is Huber Zip System. Full disclosure,
they've been a long time show sponsor of mine.
This isn't necessarily a sponsor video,
but I do have a good relationship with these guys because I really believe in
this sheathing.
This is a sheathing that's made from oriented strand board,
a much higher grade than standard commodity based,
and you can get it in 7 16ths, you can get it in half inch,
which is brown, or you can get it in 5 8ths thick, which is also brown.
Now my house under construction,
I used standard 7 16ths on my walls.
It was green and then on my roof,
I went up to half inch zip sheathing on my roof and that's brown.
Now the reason why I think this is an upgrade from that first assembly is
because this zip system has an integrated weather barrier,
this brown facing or the green facing you see here,
this is going to shed the water and keep the OSB perfectly dry.
They also have a fantastic system of tape and fluid applied to take care of the
joint. So when the framer installs it and nails this on,
then we're going to go ahead and use the tape and the liquid flash to make this
a both watertight. But also here's the big upgrade,
a much more airtight assembly. Now,
when you look at this assembly number three,
what you're seeing is we can air seal between the sheathing and the concrete.
That's zip liquid flash.
You could also use other fluid applied products as well.
They're polywall makes blueberry, which will work really well.
Prosago makes fast flash and joint and seam, which would work really well.
Now I can air seal where the house meets the foundation.
And remember anytime we air seal,
we're also going to do a great job of bug sealing and keeping those bugs out of
our house. So this is a big upgrade.
It's not a quantum leap forward in terms of insulation value,
but it's a huge jump forward in terms of air tightness.
And remember air is secondary only to waterproofing when it comes to those
control layers on our house.
We take a quick break here real quick and use an example.
Yeti coolers.
Why are these so effective? There's really two reasons. Number one,
there's no thermal bridging.
You don't see these insulated from wood studs and then they've put insulation in
between. These have continuous insulation.
This lid right here is one latch as well too,
is one big piece of insulation in here. And it's about, I don't know,
inch and a half thick, let's say. And secondarily,
the second reason why these work so well is because you have a really good air
seal. See this rubber gasket that runs all the way around the lid.
When I close this lid,
that rubber gasket seals up nice and tight and they've got these rubber straps
too. So that when you close that lid, it's really airtight in there.
We've got good insulation and we've got good air sealing.
And that's the Genesis for these next couple of assemblies I'm going to talk
about. Okay. So let's finish off with number three though.
This assembly is two by four construction with zip sheathing
and R15 bats. Again,
this is going to work in climate zones one and two,
but you're going to have to increase to a two by six cavity.
If you're in climate zone three, four,
five and this assembly would work in all those. Now this,
now we're going to bump up another 20 ish percent.
This is $2 and 63 cents per square foot of the assembly.
And that's a 21% increase over standard OSB and house
wrap, uh, with fiberglass bat insulation.
So we've gotten to a higher density rock wool.
We've gotten to a better zip system.
I'm not counting all the accessories though.
So take this with a grain of salt. When I'm giving you these numbers,
I'm not talking about the liquid flash.
I'm not talking about tapes and sealants and all that kind of stuff.
I'm really just talking about strict material costs.
I'm trying to give as much of a closer apples to apples as I can on these
assemblies. All right. And assembly number four,
what I like about this assembly is now we can build a two by four wall that will
work in any climate in America, including Alaska. And my assumption is Canada.
I actually don't know the Canadian building codes super well,
but if Alaska works, my assumption is it's going to work in Canada as well.
And that's by using a product like this. This is zip R.
This is insulation bonded to zip sheeting. So this is R3,
zip R3, uh, R3 insulation bonded to zip.
The way you install this is you're going to nail through the insulation.
The zip is still going to be on the outside.
You won't even be able to tell actually,
when you look at the house that there's anything different.
And what I like about this is it's really straightforward and standard for the
framer. For instance,
my friend Matt Carriker when he's renovating his abandoned mansion,
he did the zip R3 his builder who had never done any exterior insulation before
was able to do it really easily with a framing crew that had no, uh,
idea about these insulation details at nails on really simply.
And now we've got all the same waterproofing details.
Plus we've got exterior insulation. Now, if you're in two,
if you're going to use two by four walls and you're in climate zones,
three, four, and five, we need R5 on the outside of our building.
So we're actually going to want to go to this. This is R6.
So now we're going to be able to meet the code.
We could do two by four construction with this zip R6,
which is an inch and a half total in thickness.
And now we're going to meet that code.
Now if we're up in Alaska or Canada,
you're going to want to go to one of these two to meet your codes and those
areas you're going to need R10 on the outside with a two by four wall or with a
two by six wall, at least R5. Now this is R9 and R12.
We're talking about a total thickness here of two inches and a total thickness
here of two and a half inches. And again,
I like this because the details are really straightforward.
We can still air seal and we can install our windows. Pretty standard,
pretty straightforward with this.
We're not changing anything from the way we framed houses in America for the
last 75 years. Okay. One thing I want to note in this detail though,
as we get to the foam on the outside of the zip R sheathing,
we want to protect that bottom of the foam. And here's a great way to do it.
I got this detail from my buddy Steve Basic and I did this on my house where
we're going to rip a pressure treated two by to the thickness of the zip R.
So if it's one inch, inch and a half, two inch or two and a half inches,
we're going to rip that pressure treated to that thickness.
And now we can use liquid flash by zip to basically air seal and bug seal that
base of the, of the house. Anytime I remodel,
all the rot I found on older houses is on this bottom one to two foot area.
So if we can really do bomber waterproofing and that bottom one to two feet,
we know for the most part that our houses are going to be in good shape for
decades to come. Okay.
Before we move on to the last assembly for today anyways,
let's talk about pricing for this wall assembly.
So if we did a two by four wall with zip R3 and a Rockwell R15 bat and a two by
four wall,
now we're talking about $2 and 95 cents per square foot in today's prices of
that assembly. But check this out. We really jump up in performance.
Our effective R value now is R14.7.
I really like that.
That means we've got over a 50% bump just in insulation performance from where
we started at that first assembly or two. That's really, really good.
And this is only a 12% jump compared to just standard zip and standard
insulation. So for only 12% more for that wall square foot,
we can go up to this. I really like that.
Let's talk quickly about where zip R is in price today.
Then this is per four by eight sheet. And again,
this is my local price just to kind of give you some local flavors per square
foot for the zip R3 $1.38 $1.53 for the R6 zip zip R9 $1.72 and zip R12 $1.88
per square foot material only.
So really cost effective and relatively straightforward way to add that
exterior continuous insulation to get that Yeti cooler effect,
so to speak, and get rid of all those thermal bridges from your studs. Okay.
Last assembly for today.
Let's talk about bumping up to two by six construction now.
And this is actually an assembly I've done a lot here in the South over the
years, two by six construction with plywood in the outside.
And now we're going to talk about some other weather barrier options in the
South and climate zones one, two, and three poly walls,
a luma flash plus with a silver facer bomber waterproofing the outside.
I really, really like it. Now it does cost a little bit more,
and we're going to put a high density bat in there.
We're going to use a Rockwell R23 in that cavity.
Now we're talking about $4.17 per square foot.
So that's about a 40% jump from that last assembly.
You need to decide if that's the right move for you and what your goals are,
how much exposure that does the house have and all my houses that have really
high exposure, meaning no overhangs, really modern construction.
This is my go-to. I use this all the time. This is a really good assembly.
All right, guys, we, we went through a lot of data today.
There's a lot to talk about here, but stay tuned for my next episode.
I have five more assemblies that I've been working on,
which take the performance even higher. We're going to talk about two by sixes,
two by eights. We're going to talk cost.
We're going to talk about some other exterior insulation choices,
including Rockwell's comfort board and some other ones stay tuned for this next
episode. And again, we're going to get into costs on these as well,
but hopefully you learned something today.
And if you're talking to those production builders out there or those builders
that are using those more standard assemblies,
talk to them about these upgrades.
I really think these are going to make a big difference and not just
performance, not just our value or insulation,
but I think these are going to make a big difference in the longevity and the
durability of our buildings in America,
because ultimately does it really matter how insulated the house was?
If it falls apart and has water damage and mold and rot? No,
we need to remember that water's our enemy.
We got to get our water and all of our details that come with waterproofing.
Correct. And remember when air leaks in too,
it's usually bringing humidity in as long as it's as long as we're talking about
the South. And when that humidity hits a cold condensing surface,
there can be water problems with air leakage as well.
So remember that Yeti cooler example, we want continuous insulation.
We want good air sealing, and that's going to lead to better performance,
better comfort, better build houses.
Also big thanks to my friend Lou Varney, who did all these renderings for me.
Lou knocked it out of the park and really allowed me to show you visually what I
was looking for on these different assemblies.
He's working on the next five for me for the next video.
So stay tuned for that and go follow him on his Instagram feed. Guys,
if you're not currently a subscriber, hit that subscribe button below.
We've got new content every Tuesday and every Friday. And by the way,
if you want more on high performance construction,
I'd love to have you go check out our website, buildshownetwork.com.
I've got several other builders and an architect.
I mentioned him earlier, Steve Basic,
shooting videos on how to build a better house.
Go to that website and click on the link for our newsletter.
So you can get an update every Friday on what's happening.
If you're not currently a subscriber, hit that subscribe button below.
We've got new content every Tuesday and every Friday.
Follow me on Twitter and Instagram. Otherwise,
we'll see you next time on the Build Show.
