David Keller (@ddawgdavid) and Ben Black (@benblackii) did a ton of highline bolt homework and is developing their local crag (Buckskin Crags in Canon City, CO) with great bolting technique. David put together this video showing his process so you can learn from a real life example.
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap Raw Data spreadsheet + corresponding footage associated with each break.
Do you want to learn how to install glue-in bolts from people who've never done it before?
Check it out on this episode of How Not to Highline.
Hi, my name is David Keller and welcome to my gear closet. Yesterday we bolted two highlines
at the Buckskin Crags in Canyon City, Colorado. We are planning on bolting seven highlines here
and we are ultimately going to have a festival hopefully at the beginning of this fall,
so stay tuned for that. A big disclaimer for this video. Everyone involved in the bolting
process this weekend was a beginner. We felt like we did the necessary research and had the
right equipment to do it safely. We made several mistakes. We hope to share them with you so that
you can learn from them. With that said, check out how we bolted two highlines this weekend.
So we're planning on doing a three-bolt anchor to go to the other side.
Ideally we would want to do an equilateral triangle, but as you can see the rock here
is really bumpy and has a lot of features so you kind of have to work with the rock. We've
hammered everything a bunch of times and it's not exactly an equilateral triangle. This is about 18
inches by five feet and five feet, but we're okay with that because the middle bolt will always see
the most load, so pushing it back an extra couple feet is probably a good thing for equalization.
So one of the biggest things that you need to be concerned about before you bolt something
is rock quality. Ryan has a great video discussing the various kinds of rock and I suggest you read
the chapter in the bolting bible discussing this. Colorado is famous for really bad rock quality.
We knew from a local geologist that the spot we were bolting was red granite, which is pretty
rare and good quality rock for Colorado. Nevertheless, we weren't sure if the spot
where we wanted this highline to be was going to be really solid granite,
so we decided to overkill everything, especially since this was our first time.
We decided to use the 12 millimeter by 150 millimeter monster crux bolts. These are
rated to 60 kilonewtons, the eye is, so we're never worried about the metal actually breaking.
And we are using the Hilti, what is it technically called, the Hilti Hit RE500V3 glue.
This is basically the top of the line stuff that you can buy. It is definitely overkill for most
applications. The reason we went with this is because we have a Hilti pro deal, so it was
relatively affordable for us to get this. If I was to do it myself and I didn't have a pro deal,
I would consider other glues like Liquid Rock 500 is a great alternative.
The other pro to this is that it cures down to 23 degrees Fahrenheit. We were not sure when we
were going to be bolting, so this was an extra benefit to say if we were going to bolt on a
cold weekend that we could still get away with doing it. So we're about to drill our hole,
but before we do we need to know how deep to go. Today we're using the 12 millimeter by 150
millimeter Monster Crux bolts, and essentially what that means is that to the bottom of the eye
it is exactly 150 millimeters. You can see right there. And online it says that you
should drill an extra five millimeters deeper, so that's what we're going to do.
We're here with Ben Black. He has bolted several climbing routes in the area,
and he's going to give us some pointers on how to drill the perfect hole.
But first, Ben, what are you holding in your hands? I'm holding a Hilti 36 volt rotary hammer drill,
and it's got a Bosch 916 SDS drill bit in it. Perfect. And do you have any tips on drilling
the perfect hole? Just keep your hole perpendicular with the rock and keep it as straight as you can
when going in. You can use your knee if you need to to keep it straight. Hold it straight.
Other than that, just let the drill do the work and don't push too hard. This is an extra step
that we're taking in the bolting process. Essentially we have dry fitted the bolts,
so they are not glued yet and they are not notched yet, but we have tied a sliding X
to see where the rope is going to want to go straight across. And the idea is that we're
going to make the notches parallel to the strands of rope. And the reason we want to do that is so
when you show up here and you're tying a BFK, sometimes it's hard to get it perfect, but if you
can use the notches of the bolt to indicate where the leg should go, it'll be really easy to tie a
notch for our bolts. We ran into several difficulties. It was much harder than we
thought it would be, especially because the rock that we were bolting was not perfectly flat.
It had many features and little bumps that would kind of push the drill bit around,
making it really hard to drill a perfectly straight notch. So the strategy we followed
was a little different from the one that Jerry used in his video, or in Ryan's last video.
Basically, we drilled our first hole for the spine of the bolt,
then we drilled a second hole straight down at the end of the eye. So you have the main
hole and then a smaller hole right here that is only the depth of the bottom of the eye.
You don't want to go too deep, otherwise you waste some glue.
These two holes drilled, we then found it easiest to drill one right in the middle. So now you have
three holes, one really deep, two shallow. From here, we took our drill at a 45 degree angle
and cleared out the rest of the rock in between here. And we did what you shouldn't do, which is
to kind of abuse your drill bit and use it kind of as a chisel to scrape and make this flat,
but that's what we did and it worked pretty well. We were using a Bosch drill bit and my friend Ben
said that he was very confident that we couldn't break it. So I don't recommend you do that,
but it is what we did and that is how we did most of our notches.
I would like to take a minute to talk about the rationale behind putting in the bolts backwards.
So essentially, bolts, especially p-shaped bolts, have always been used like this, where the rope
is pulling at the end of the eye. And the challenge with this is that your notch has to be pretty in
line with the direction of your rope. So if you look at it like this, you want it to be straight
on. The challenge with this is that if you notched incorrectly or you did it in the wrong direction
and in reality your bolt is slightly twisted, you are now creating a lever arm which can create a
torque on the bolt and crack the glue. We decided to put in our bolts backwards so that the rope
would be pulling on the spine of the bolt and this way no matter which direction you pull on the bolt
you're not going to create a torque. This is kind of good for our application because we're talking
about potentially doing a space nut out there or we're not sure what the direction of the high line
will be. So that is why we put in our bolts backwards. Another topic worth emphasizing is
how important it is to clean the hole. I ordered this dust pump and it was supposed to be here
last Friday. However, Colorado had other plans and we had a massive ice storm which delayed my
shipment. We scheduled everyone to be bolting on Sunday and I didn't feel like it was worth pushing
it off another weekend due, so we cleaned our holes with the traditional blow tube method. There are
several reasons why I believe a dust pump is well worth the money. The first being that this
definitely has a lot more blow force, if that's a thing, than someone blowing through a tube and
especially if you push really quickly you get a lot of air moving really fast. It's a great way
to clean your hole. My second concern, and I think it's my biggest concern, is that we used the blow
tube to clear out all six holes and by the end the blow tube was definitely building up moisture
from the person who's blowing. Their breath clearly had moisture and was building up in the tube
probably going into the hole. The dust that we were trying to get out of the hole probably
interacted with that moisture and didn't want to come out as well, so the moisture from your breath
probably makes cleaning the hole a lot harder. I don't have that problem with this. And my third
reason is that if you make one poor soul blow out all your holes because he's sick, then he might
feel really lightheaded by the end of the process, especially if you do five blow cycles per hole,
which is what we did. If you're really lightheaded on a cliff edge, it might be dangerous, which is
something to think about. One nifty trick that we used when we were cleaning our holes is that
as soon as we were done cleaning a hole, we covered it with a small piece of duct tape.
I think this saved a lot of time because as soon as we finished a hole, we covered it,
went on to blow out the next one, and we would blow dust all over the place, but we knew
that the hole we just cleaned wasn't getting dirty. One of my biggest concerns for this
bolting project was knowing how much glue to use. Ryan told me that this 11 fluid ounce canister
or capsule was sufficient enough to fill six holes. That proved to be absolutely correct.
We were able to do six test squirts or trigger pulls into a plastic bag before we started
filling our six holes, and we were able to do six test squirts after we finished gluing
all of our holes. So this 11 ounce canister was perfect for six holes plus 12 test squirts,
and we completely used it all. We used all of this glue.
One of our goals was to try and keep our bolting area really clean of excess glue.
We did that by using duct tape yet again. We created a small rectangle around our bolt hole,
and as we filled it with glue, we were kind of aware that excess glue would spill all over the
place. It is a messy process. The duct tape allowed us to peel the glue off later when we
were done, leaving some really nice clean rectangular glue blobs right over our bolts.
The mistake we made is that we let our glue cure too long. We ran off and got lunch, came back,
realized that the glue was super hard, and it was kind of a pain to get the duct tape off out of the
partially cured glue. So make sure if you do the rectangular duct tape method that you peel off
the glue basically as soon as you're done gluing, and that'll make the area look really clean.
Another mistake we made was that when we inserted our bolt, we did not cover the bottom of the eye
with glue. This was shown in Ryan's previous video. I totally forgot to do it. Instead,
I made sure to keep this area nice and shiny. I'm not sure if it is a mistake though because
it preserves a lot of the space in the eye. It is not being occupied with this glue,
and Ryan also told me that if that glue that is covering the bottom of the eye is not perfectly
smooth when it hardens, it can get really sharp if there are any ridges on it. So we didn't cover
the bottom of the bolt with glue. Let me know if you think that is a problem. I personally think
that the six inches in the rock, that glue is what is actually holding you. This is to just
kind of prevent the torque in it. The eye is still in a notch, it's just that we made this perfectly
flush with the rock. Let me know if you think that's a problem. Trying to be environmentally
conscious, we decided to sprinkle our red glue with local pebbles and dust. The mistake there
was the word pebbles. The local rocks there, even though they're very small, are really sharp,
and we are concerned that once the glue is hardened and those things aren't moving,
they might be a source of abrasion. If you have really fine dust in your area or you manage to
save some of the dust created from drilling, I think that is exactly what you should use.
So just be aware, don't use pebbles that are really sharp or too big because they might
cause problems later. There are some extra pieces of equipment that I think made the
bolting process much easier. The first was rubber gloves. Having rubber gloves kind of got rid of
the fear of touching the glue and making it look pretty. I did touch the glue without rubber gloves
and it kind of sucks. Your hands get super super sticky obviously. Another piece of equipment
is q-tips. With the q-tips you're really able to polish up your glue and make it look nice,
push it to where you want it. We used a lot of q-tips. Definitely bring more than you think
you should. I think we used a total of 10 or 12, which is kind of ridiculous, but it gets really
messy, especially if you have a lot of excess glue. And if you're trying to be a perfectionist,
bring a tape measure. We were able to know exactly the dimensions of the triangle we bolted
and it kind of made me feel warm and fuzzy that we're at least trying to follow
good highlighting standards by keeping a nice consistent shape. My final comment on the bolting
process as a whole is to not totally be afraid of doing it. It is not rocket science, but please
respect the process. There is a lot to know. I personally felt like I had to read the bolting
bible about five times before I felt really confident in what I was doing. I watched as
many YouTube videos as I could on the subject. Many of them were not in the language I speak,
but I learned what to do, what not to do. The more knowledge, the better for me. And I asked Ryan
a bunch of questions. I don't necessarily recommend that you do that because he might
just make you make a YouTube video for him, but I also would recommend trying to go with people
who know what they're doing. Obviously, that wasn't really an option for me. I did go with
my friend Ben, who had bolted several rock climbing routes in the area, but most of his
experience was with mechanical bolts, so gluon bolting was new for both of us. I hope this video
is helpful for you guys. There's a lot to know, a lot of mistakes to be made. Just know what you're
doing, I guess. Good luck. Installing gluon bolts requires a lot of time, money, and effort.
Therefore, you should let your friends do it. Hey, thanks for watching, but don't be an idiot
and tell me how stoked you are on a project you've put a lot of time and effort into,
or I'll tell you how much fun it is to make an episode. Thank you, David Keller. You did an
amazing job, especially for your first time bolting. They were great bolts, and you articulated
everything really well. You can find out a lot of information on the Bolting Bible, and we have
links to other resources that can help you learn a lot. We are going to continue to make videos
correlating with the Bolting Bible and also more bolting examples. Now, before you go highlining
for your first time, please go with someone who knows what they're doing. There are a ton of
festivals these days that you'll find mostly on Facebook, and you'll have Slackademics groups
that we put over 1,300 Facebook groups from everyone all over the world, so you can find
a slackliner near you. I also offer private lessons now in case you want to message me about
a customized course with you depending on where you're at. If you're really stoked about this
channel, please consider donating $1 per episode on patreon.com or donate on PayPal, a one-time
donation, or buy a t-shirt like this or some of the ones that you saw David Keller wearing. If
you donate or contribute like David did to this channel, we will put your name on the ending
credits, but also you'll get exclusive access to all of my Slack Snap data and all the footage
correlated to it. I break stuff almost every day here at home, and I probably put out only
10% or 20% in episodes, so I have a wealth of knowledge available to those who get involved.
All the money we do earn in Slack life goes right back into making these episodes better,
so don't forget to subscribe so you don't miss any of them. Cheers.