😍 Join Makers Gonna Learn & Use code "BEST" for $40 off, GRANDFATHERED in, and LIMITED bonuses! Get a PRINTED Cricut REFERENCE BOOK + Mystery GIFT! Join now: https://bit.ly/3Nk7sDr 😍
If you need something spectacular for your holiday table, you’ve come to the right place. This 4 foot long wooden centerpiece is stunning! And believe it or not, you only need 1 power tool to make this. Learn how easy it is to make a gorgeous Cricut centerpiece with our step by step tutorial.
Some of the links provided are affiliate links. Makers Gonna Learn is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program. As an Amazon Associate, we earn from qualifying purchases. This means, at no additional cost to you, we will earn a commission if you click through and make a purchase.
Hello everyone, welcome back to the Maker's Gonna Learn YouTube channel. In today's video we are
going to be teaching you how to make your very own custom centerpiece for your table.
Now I know there looks like there's a lot of power tools on this table but do not let that
discourage you from trying to make this because it is so easy and it is really going to elevate
your decor to a next level. If you are new to our channel, Maker's Gonna Learn is a membership-based
crafting community where we bring you inspiration, motivation, and education to get your Cricut out
and master it. Make sure to check us out at makersgonnalearn.com. You can like this video,
follow our channel for more free content, and hit that bell notification so that you can be
notified every time we go live or premiere a new video. With all that being said, let's go ahead
and jump into the materials that you are going to need to create this centerpiece. So to start off,
the base of our centerpiece is going to be a four by six. Now when you purchase a four by six you're
going to find them in either an eight or ten foot section but you can have the hardware store that
you buy this from cut it down into the size that you need. So a good rule of thumb is to measure
your table to see how long of a section you need. You may not need a four foot section. This is a
four foot section. Your table may not be long enough for that. So make sure you measure before you go
purchase so that you know exactly what foot to tell them to cut it at and they will cut it down
for you. I also want to make sure you guys know that a four by six is sometimes a little bit of
an oddball size so you may want to call around different hardware stores to see if they have it
in stock before trying to run around and find one. Next up you are going to need a drill. Now the
drill bit that we're using today is called a spade bit. So what this does is this you can you
put place this point on your wood and it turns and it creates a perfect circle. So for the candlesticks
because we are going to be putting candlesticks in this we are using a seven eighths spade drill bit.
Next up we have our palm sander. This is just to give our wood a nice even sand all the way across.
Also because when you use the spade bit it's going to give these get these edges kind of rough so we
just like to go over it with our palm sander and especially because we are staining this
using this sander to sand all this down will really help the stain penetrate into the wood.
I would suggest using a 120 or above grit sandpaper. Now I want you to remember when it
comes to sandpaper the higher the number the finer the sandpaper. So if you have a 200 grit
sandpaper it's going to be really really fine and then the lower the number the rougher it is. So we
really want to give this a nice finish so we want a higher grit sandpaper. Next up you are definitely
going to need a measuring tape. Now the reason we're going to need a measuring tape is because
we're going to be putting 24 holes in this centerpiece so that we can put the candlesticks
down in it and we're going to have to measure and mark this off so that we know exactly where to put
our holes for the candlesticks. You're also going to need a pencil to mark where to drill. Next once
you have done all that we are going to finish our centerpiece with some Minwax wood stain. We are
using our favorite this is Early American it is absolutely our go-to stain. I feel like it is a
good medium it is not super light but it's not too dark so this is the same that we're going to
be using today. We do have an old t-shirt that we cut up and use as stain rags this is by far my
favorite way to stain is just using an old t-shirt an old drop cloth something like that that can
really get that stain into the wood grain. Last but not least because y'all know we can't make
anything without using a Maker's Gonna Learn file or font we have a cream colored permanent vinyl
as well as our Nicopa light grip mat so that we can give this centerpiece a nice little touch
that really is going to make it a true holiday centerpiece. Now that we have gone over all of
our materials let's go ahead and jump into making this project. So first thing that you're going to
want to do is you're you are going to want to give this a nice good sand so we're going to go ahead
with our palm sander and we're going to give this a sand. Remember I said we were using
a 120 or higher grit sandpaper so we're just going to make sure we sand out any imperfections
that this piece of wood has. Now that we have sanded this we're going to hop overhead so I
can show you how we are going to measure this out. So as you can see I have already mapped out one
side and drilled this one side down because we're actually going to be working with 24 candles. Now
this is going to be something that you are going to have to determine how much you want how many
candles you want in your centerpiece how long your centerpiece is. So what I'm going to show
you we're working with a four foot piece of lumber so what I have done and this is what you all need
to do whatever length you want your centerpiece to be we are going to measure that make sure it
is exactly that length like I said we are working with four feet and then we're going to mark the
center point of this piece of lumber. So as you can see we have two feet so we are going to mark
it here and I'm actually going to come down mark it here and then back up and mark it here.
Once you have it marked you can use a straight edge if you want or really you can use anything
you have that will keep the the edge straight so I'm just going to use our nicopimate and I'm just
going to mark this so that I know where the center line is all the way across. Now that we have marked
our center point on our piece of lumber we are then going to mark the center point here so because
this is a four by six we are looking at three inches should be your center point so I am going
to mark three inches here and then I'm just going to keep going down my piece of lumber and keep
marking three inches. I have marked three inches all the way across here once again if you have a
straight edge you can use a straight edge we're just going to use our nicopimate because this
still gives us a straight edge and we're going to line this up so you're going to line it up so it
goes flush up against all of the marks that you just made and we're just going to come through
here and mark it. So now we have our center line marked this way as well as this way and it's very
faint don't worry you can come back over we're going to sand this out these light pencil marks
so it's not a big deal. Now that we have both of these center areas marked we are going to determine
how many candlesticks we want so a good rule of thumb right now we're working with 24 inch
section so you need to work with a number that is going to be divisible by 24 so you're think
you're looking at two inches three inches four inches would be a little more space out because
we want so many candles on our centerpiece we're actually only going to be working in two inch
sections so what we're going to do from here we're just going to come down here and mark
every two inches once we have our two inch sections marked we're just going to take the
straight edge of our mat and we're just going to mark those the good part about this is you do not
have to be 100 percent precise we are building something but it's not like it has to fit together
we're just going to be drilling holes and we just want to measure to make sure that our candles are
close enough to evenly spaced apart that nobody's going to be able to tell so once you have your
four by six divided into two halves and you have it into two inch sections we're then going to come
in here and we're going to mark alternating sides where we're going to place our candles
so as you can see on this side i started here and then moved down to this section and up and down
so we're going to do that on the opposite side as well so since this one is up here i'm just going
to place an x here and then keep moving down my four by six until i reach the end now your x's do
not have to be in the exact center of where you measured out but as long as it's in the general
area of the center of that block it will be fine so now what we're going to do is we are going to
take our spade bit and we are going to drill a circle into our four by six a little tip of
information so if you want your candle six all the same all the way across one thing you can do
is you can either take a piece of tape or a marker and you can draw on your drill bit where you need
to stop so what will happen is once you're you will be able to see how deep the drill bit goes
and once your mark reaches the top of the wood then you can you will know to stop that way they
will all be the same all the way across we're actually wanting our candles to sit higher and
lower so some of my holes are going to be more shallow while others are going to be deeper
because we really like the variation of the different heights of the candles now we're going
to start the process of drilling all of these holes now that you finish drilling all the holes
what we're going to do i have a pretty large trash can sitting here i'm going to actually flip this
over and i'm going to get all of the extra sawdust out of these holes that we have drilled now that
i've gotten all of the extra sawdust out of our centerpiece i'm going to grab my palm sander and
i'm just going to give this a nice even sand so that i can get these little edges off of here
so another thing i'm going to do is i'm going to take some 220 sand grit sandpaper and i'm actually
just going to roll it up and then come in here in these holes and get off these edges that are deep
down in there that the palm sander could not get now keep in mind the sanding of these holes does
not have to be perfect because you're actually going to take your candlestick and it's going to
go in down in there and it's not going to show so you're not going to be able to see that so it's
really not that big of an issue next thing i'm going to do is i'm going to prepare my surface
for the staining portion now this is going to be entirely up to you if you are staining
on something that you don't want to get stained on make sure that you grab either a trash bag
and cut it off you can get a drop cloth or something to protect your surface if you are
standing outside and it doesn't matter then you can skip this step but we are going to protect
our work surface here and then we will begin staining now that we have our work surface
prepared and ready to stain i am going to put my gloves on because i do not want to get stained on
my hands and then we're going to open the stain and start staining now one thing i do want to say
you definitely need to stain in a well-ventilated area if not then you need to wear some proper ppe
we are in a very well-ventilated studio so and we've got the door open so we are good to go
but make sure that you are staining in a well-ventilated area one thing you are going to
do before you start staining is make sure that your stain is really well shaken up because you
don't want that all the stuff that settles on the bottom to be on the bottom so we're just going to
make sure our stain is shaken up and then we're going to open up our stain now what we're going
to do is we're just going to take our scrap piece of cloth dip it down into our stain and start the
staining process now one thing that's going to be a personal preference is the staining inside these
holes you can if you want to remember our candlesticks are going to be in there but if you
want to you can it will probably it's going to give it more of a finished look but it's going to
be really hard to get down in those crevices so my advice is just to stain up toward the edges up here
and then we'll wipe away the excess now once you have finished staining you're going to want to
let this cure for about 24 hours before we move on to our next step now while our centerpiece is
drying from the stain we're going to hop over to design space and I'm going to show you what font
we're going to be using to put on the centerpiece so here in design space so that we can really
elevate this and make it a true holiday centerpiece we're actually going to put the word
joy on the side so it's not overwhelmingly holiday but it still has a holiday feel to it
so we're just going to come down here to text and the font that we're going to be using today
is demonstrate now we're going to come over here to maker's going to learn and I'm going to show
you exactly how you can download maker's going to learn fonts and files we are going to go to our
font section so like I said earlier maker's going to learn is a membership-based craft community
where we bring you thousands of cut files a month hundreds of fonts and you get commercial license
to use all of this so if you wanted to make these centerpieces to sell you could use one of our font
and would have the commercial license to be able to sell it so we're actually going to be using the
font demonstrate today we are going to click on this and the one thing I love about our website
is that you can type in the word that you plan on using to see if it looks right so today I think
we're going to be using the word joy and I'm not 100 sure if I want a lowercase j or a capital
j so let's try it both ways so first we're going to try with a lowercase so I can see that this
lowercase j and the y kind of go together and I'm not really a fan of that so let me try it with an
uppercase j and I like that a lot better so now what I'm going to do I'm going to come here to
the cloud icon and I'm going to click download it's going to download as a zip file you're going
to open that zip file up from there you are going to install the font on your computer and then we
are going to go back over to design space we are going to go to view reload because once you
download a new font you do have to reload your design space to be able to find it we are going
to bring our text back in here come up here to our system fonts type in demonstrate and there we have
it so now we're just going to type out joy and we are going to size it according to our centerpiece
now we are working with a four by six so our height we can do it about I would do about three
and a half to give you a little room up both up and down so from there we don't have to do anything
else all we have to do is click make it we are going to be doing this on the maker series today
but you can do this on a maker an explorer or even a joy and we are just going to be cutting
this on premium vinyl now that we have our word size we're just going to go ahead and push it
through and have our cricket cut it now we're just going to cut this take our extra vinyl off the mat
and then I'm just going to go ahead and weed this while it's on the mat I love weeding while
my design is still on the mat because it's works kind of like your third hand so you it's very easy
to weed now that our centerpiece is ready we are just going to add our transfer tape down
and we're going to burnish from the front and I also like to burnish from the back I really think
it allows the vinyl to stick really well to the transfer tape and now we're going to grab our
centerpiece and attach the word joy to the centerpiece now to apply this we are just going to
lay this down once again I'm going to get my burnishing tool to burnish it down onto
the wood once you have that burnished down we are just going to take our transfer tape off now you
are going to want to be careful with this because it may be a little finicky to take off so just be
very careful you may want to use your weeding tool to come back through and make sure that it's
down very well wow that was a lot but you have an absolutely beautiful centerpiece that you can use
for years and years one thing that I want to make sure you guys gain from this video is to not be
afraid of power tools power tools are really a crafter's best friend once you learn how to use
them they are a great thing to have in your back pocket so that you can pull it out whenever you
need to so I really hope that you all have learned more and are more confident in using power tools
and I can't wait to see what you all create I will see you guys in the next one bye