#SSBC is exactly as it sounds. I am more of an enduro bro, who cares more about riding my bike, than tinkering with my bike. My friend Matt, from Bootleggers Bikes in Jeffersonville, Vermont is definitely more of an engineer, who loves to tinker. Together, we are going to break down complicated bike subjects into a simple chat that will help you learn more and enhance your riding. Every episode will be a new and exciting subject, and there are no limits to what we can discuss.
If you have any added information or insights on a subject, want to shred our opinions or facts, or any suggestions for future videos, don't hesitate to comment below and share. We want this to be a community discussion and welcome all perspectives!
Most importantly, enjoy the video and be sure to leave a comment below and subscribe for more!
- My Ride: https://dirtlab-usa.com/ - Check out the Nobl Carbon Wheels I run: https://bit.ly/2VnRga7 - Want to protect your wheels?: www.cushcore.com - Check out my favorite pads: www.g-form.com - My riding gear: www.100percent.com - My favorite riding snack: www.untapped.cc - Coffee fan?: www.atomicroastery.com - Need some delicious protein for recovery?: www.ascentprotein.com
Yeah, that's us. That's what we look like.
What's up everyone? Jimmy here from MTB Travel Review. I'm back with my friend Matt.
They call him Tinker Matt. Nobody calls him that, but engineer, shop mechanic,
one of the owners of Bootlegger Bikes up here in Jeffersonville, Vermont. Welcome to episode
three of Stupid Simple Bike Chat. It sounds exactly like it is. We're literally taking
overly complex bike stuff, making it simple enough for you to understand and learn a little
bit about that thing that you enjoy riding so much. On episode three, we are going to talk about
tubes versus tubeless tires. When I first got into mountain biking, tubes were all you ran.
You had your rim, you put a tube inside, you put your tire over it, right? And there was a lot of
flaws with tubes. I feel like one of the biggest flaws when I was riding as a kid with my dad is
you would ride over a bunch of thorns and you'd get a hole in your tube. You always had to have
patch kits and you're stopping every 20 feet to fix your tube. It was just overall a pain in the
tushy. Since then, everything that you see now for the most part, at least on upper level bikes,
is tubeless. What exactly is tubeless? How exactly does that work is a good place to start?
Tubeless really mimics the... We've been running tubeless tires on cars for many years.
It's an air and relatively liquid tight seal between the tire and the rim. There are a couple
different aspects that we need to consider when we're talking about tubeless. It's not just the
tire and the rim, it's the rim tape, it's the sealant, it's the valve stem. You're literally
taking the tube out and you're just making an airtight chamber. You have the tire on top and
there's an airtight chamber in there. That's where you talked about the liquid to hold it in there.
When it comes to the rim, let's start with the rim. We have a rim here. The primary difference
you're going to see in tubeless versus tube is that for a tubeless rim, this needs to be an
airtight chamber. We have what's called rim tape here. From what I understand, it's just covering
the holes that your spokes go through and just making this an airtight chamber, right? It is,
exactly. Essentially, all rim tape is doing is it's sealing the holes from the inside of the
rim to the outside. That's all we're looking to do. We're looking to plug up those holes,
whatever they are. Mostly nipple holes, sometimes drain holes on carbon rims,
sometimes drain holes on aluminum rims. That's pretty straightforward. The tire has obviously
sealed itself. That's not a big deal. What about the stem? If you've ever run tube stems,
you know that you have a stem which is attached to the tube. We have a tube here. This has your
typical stem on it. This is a Presta valve or a Schrader valve. That's where you pump your air in
the tube. The stem goes through the rim. The tube sits on top, straightforward. Obviously,
that's not going to work with tubeless. What do we have to use to run tubeless?
It's essentially a valve stem that's been isolated or set alone from an inner tube. It has a fancy
little O-ring seal, whatever you want to call it. When it interfaces with the rim, it produces a
good seal. That's what sits in the rim and makes that airtight sealing? It does. Because this pokes
through that tape, right? You put the tape and then you poke a hole in it. It doesn't make much
sense until you have this rubber gasket that keeps it sealed. Exactly. That's really all it is,
taking the valve stem off of the tube and interfacing it with the rim. Before we go into
more depth on stems, the last piece we really need to know for tubeless is the goo, the liquid,
the sealant. If you just put your stem in here, you put your tire on, you fill it with air,
basically all the air is just going to leak out, right? It will eventually leak out. Most
widely known tires like Maxxis or WDB have a great bead. You technically could set this up
with no sealant and seemingly it will set up very well and hold air. The bead is what seals it. The
bead is the end of the tire that sits inside the rim, right? It makes that connection. Over time,
it will lose air. That's where the sealant comes into play. We use sealant for two reasons. One is
for what I just described, where we want to seal that bead between the tire and the rim.
If there's any little bit of air that leaks out, the sealant will make its way in there.
It will solidify and seal that hole. The other reason is if we're riding down the trail and we
run over a staple, that staple typically would induce a flat on a tubed tire. With a tubeless
setup, the staple might go in, it might stay in, and you won't even know it. You'll be riding along
and you'll be having fun. You'll go down to the gastro pub afterwards and you won't even know
that you had a staple on your tire. It's actually just that staple will remove itself. With a tubed
tire, once the staple's been removed, you've got a flat. It's immediate. You know you have to
replace that inner tube. With a tubeless setup, you probably wouldn't even know that that staple
punctured your tire and has since gone into the woods. The sealant will seal that small hole.
It's a liquid sealant, but obviously there's a chemical combination in there that when it
hits air, it hardens. That's where you can get what they call wheel creatures, where if you take
off a tubeless setup, a wheel that you've been riding for a little while, you take the tire off
and there's all of these rubbery creatures. That's that sealant just hardening up over time.
It is. All the scientific and molecular level stuff.
That brings us back to the stem. One of the things you have to think about when you're running
tubeless is how do you get the liquid into the tire? There's a couple ways to do it. You can
actually, when you're putting the tire on, you can leave an opening, pour the liquid in. There's
potential to get messy, but one of the more common ways is that people can actually inject it through
these stems. That's right. They're made a little different to allow that.
Most, or I would say all, tubeless valve stems have a removable core. You can remove this core
and essentially what's left is just a tube. You can inject sealant through that tube and then put
the core back in. We do it both ways here in the shop, but in some cases it'll be messy.
The other thing with these stems, I've had this happen to me, where the stems can actually,
that liquid, again, when that sealant hits air, it solidifies. If it goes through there,
through all these little chambers and then it solidifies, what happens is these can clog.
There's been advancements. We have, who is it? There has, yeah. The high flow, no clog valves,
they come up with a really cool design that basically gives you a higher volume chamber
with the core installed so that it's easier flowing and that it doesn't solidify as easily.
There's less crap in the way to get clogged, basically. Exactly. Nice.
We have this amazing new capability with tubeless tires. Another thing that I love about tubeless
and that not everybody may know is, again, reverting back to CushCore, which is one of
companies I work with, which is a foam tire liner. It's actually a tire liner. It's a piece
of foam that sits inside your rim and then the tire goes over the top. If there was a tube in
there, you couldn't do that because the tube is taking up that space. Now you have this ability
to put these foam liners, and multiple companies make them, that are, again, going to help you
with dampening and just give you a different feel, which I think is really important.
Can you tell me what's the primary difference between the feel of a tubed tire and a tubeless
tire? Are there benefits in your ride when going tubeless as well? The biggest benefit of a
tubeless tire is going to be air pressure. You can run a lower air pressure, which offers inherent
suspension to the ride. We're on a full suspension bike, so we have suspension to take up the big
hits. There are little hits where carbon can help and where lower pressure tubeless tires can really
have a huge benefit to the ride quality. With the lower pressure comes the risk with
the big hits and landing on a rock. I think that's where the Cush Gore inserts or foam
inserts help. If you picture having a tube in your tire, you can't run too low of pressure
because what happens is if you take a big hit and you crush that tube, it can actually pinch
and that creates a flat. With tubeless, you don't have to worry about that. You can run the lowest
pressure you want aside from just destroying your rim. That's where those inserts come in.
For me, it really changed the game with my riding style because you feel more at one with the dirt.
It's much more compliant. You can feel the grip on the ground better. It's a better overall
experience from what I've seen. The big thing here, though, is at the end of the day, it's not
really a debate. I think tubeless is the future in what you would recommend to most riders.
I think there's very little disadvantage. That said, we can't just get rid of tubes,
right? What's the purpose? I see a lot of riders now with tubes in their bags or mounted
on their frame. Why are people running tubeless and then carrying around a tube? You have to
still carry a tube because there are situations where you would tear a tire regardless of it
being tubed or tubeless. If you don't have a tube, the tear can be too large to repair in the field.
You carry a tube with you and you put the tube in so you can get back to your truck or your car.
Yeah. Again, at the end of the day, it sounds like tubeless is the way of the future and basically
the setup. Are most rims and tires, is most of it tubeless compatible now?
Yeah. You're hard pressed to find any quality tire or rim is going to come tubeless ready.
New bikes typically don't come set up tubeless from the factory. That's something that we do
prior to Jimmy buys a new bike from us. We would set that up tubeless here at the shop
just because of the difficulties around shipping and flying tubeless tires around and you have
sealant all over the place. They come with tubes, but the rims and tires are tubeless ready.
We simply pull out the tube, drop in a tubeless down and a little bit of sealant and you're off
and riding tubeless. Tubeless is the way of the future. Go tubeless or quit riding your bike.
Maybe not that extreme, but definitely look into tubeless if you're not running tubeless.
There are a lot of benefits. As always, guys, thank you for following along. Again, this was
episode three, many more to come. If you have any video ideas, anything you want us to talk about
in an upcoming episode, drop it in the comments below. If you think everything that we're saying
is insane, tell us we're wrong and tell us why. Help us all learn. That's the goal with all of
this. Thanks for following along. Keep riding. That's good. All that said, I forgot where I was
going. Oh, yeah. Good. Are you a mechanic? No. Do you work at a bike shop?