"LOWERING SPRINGS" On My Audi S3 8P

MotoAdventuresYT
21 followers
4 Video Views·Sep 17, 2020
Instagram - MotoAdventuresYT
Facebook - MotoAdventuresYT
Twitter - YT_Motor
YouTube - MotoAdventuresYT
Thank you for watching! make sure to subscribe for more videos on this!
Comment down below and let me know what you think about this video as well as what you want to see in the future!
https://www.patreon.com/MotoAdventureYT
https://www.instagram.com/motoadventu...
https://www.facebook.com/MotoAdventur...
https://twitter.com/yt_motor
https://www.youtube.com/channel/UC37q...
What's going on guys, how's it going? I hope you guys are all having a good day
because I definitely am. Now you've seen the description right, we are lowering the S3
in this video. It might not be this day that I'm recording this video on but it definitely will
be this video. So I've got the S3 here, we're going to take the rear wheels off. Well to be
I've never actually installed springs on an S3 or a four-wheel drive car so we're gonna go ahead
and we're gonna go ahead get it on axle stands at the rear and have a look underneath, see what the
crack is, see what I need to remove to get the springs off and then get the new ones back in.
I have gone with Apex, probably not the most best brand in the world but probably not the worst
and I've also got these clamps for the front just to, you know, help and save your job.
So I'm gonna go ahead get the rear of the car in the air and then I'll come back to you guys.
Hey guys, so I've got the rear of the car up, torch is dead so I'll put that on charge.
So I'm gonna get both the back wheels off because it looks like there's a bolt
right in there and I'm not gonna get to that with the wheels on. So both wheels off it is.
Okay so seems pretty simple enough, I think it's just this bolt and there's a nut on the back
and this will come down and then we can get our spring out and swap it over. Now I'm saying this
like it's going to be a piece of piss but it's probably not, it's probably going to be a nightmare
but yeah here goes nothing. Okay so this is an 18mm, oh f**k's sake. So I get a ratchet
for this bolt here which obviously you can't get to because that's in the ******* way
and loads of spanner kits do not come with ******* 18mms. So unless there's one in here,
yes there is. Bingo! Okay so we'll whack this one in and we'll just start turning this.
Oh yeah she's coming out. I've got the nut and bolt out, you wanna get your torques
and you need to undo three of these because this is connected to the, I believe this is for the
forward drive knowing what's on the ground sort of thing, little sensor. So three torques
and then this one's ready to drop down. Okay lads, so once you've got this bracket undone,
once you've got this bracket undone, you just want to pull it out of the way
but make sure to use some WD-40 on these nuts because mine were very close surrounding
and I just had to hammer the torques bit inside to the nut to get a good grip on it.
But next thing we're gonna go ahead and drop this arm down hopefully and it will go from there.
There you go, this is what you don't want is when you get your spring out and you realise
it's snapped already and it's like corroded at the bottom. Huh that's very odd, I've never seen
that before. I guess that's what happens, the water gets sit to the bottom there or the water
just sits there. Oh well, at least we've got some new ones now. So I've got the spring in,
basically I planted it inside, I took the boot off the old spring, put it on the new spring,
put it in, used the jack to jack up the arm back to the original spot, put the bolt in,
tightened it up, obviously I'm going to go over them later on.
I'm not going to put that sensor in yet because I want to do that last, just make sure everything
is all good and make sure these are the right springs because they do look a little bit
different to the ones I've had in there. Like these are the originals and these apparently
the lowering ones but to me, well I know these ones are snapped but there's a bit of a difference
so I don't really know whether these springs are just more compressible and these are just
more solid. But what we're going to do is we're going to fit the other side, drop it on the floor
and have a look what we're saying. Okay guys so I've just got the other side out and again the
spring is actually snapped and it's been snapped for a long time so that's very odd. I would have
thought that you know Audi would manufacture these springs a bit more durable considering
this is only a 2007 but it is what it is and like I've said before this boot that comes off the
original spring, you just want to put it on the new spring, just line it up as well,
this side, line it up and there we go, it's ready to be put back in.
In and drop the car on the wheels and yeah like I suspected I feel like these springs are the
right springs but I feel like they're just more suppressive so like they're bigger than the
originals but they're a lot more softer. So yeah I think we're good, obviously I don't know if I
believe in the whole settling thing but we're gonna, I'm just gonna say for the sake of it
they might have to settle but I think we're sitting a bit lower but definitely lower than the front
anyway and yeah, yeah I think we've done a little bit, obviously these are 30mm springs
so they're not going to be like on the deck but definitely a little bit of an improvement
and I'll have to see once we get the map done. I've actually just received the big present for
this car today and it's in the other room and that will be another video because it's going
to be a big job but yeah I'm gonna go ahead and get the rear wheels on, do that sensor back up
and then for you guys I'll be starting on the front but I think I'm gonna do that tomorrow.
Alright lads so I've gone ahead I've decided we're gonna bash up the front ones as well today
so I've actually had a good look at the rears and I do feel like they haven't actually dropped so
I feel like we're winning at the minute so on your head start on this side, get the wheel off
and I'll go ahead and show you guys how to get like the actual strut out, you get the bonnet open
and yeah let's go for it. Alright guys so looks to me, get the torch in this,
so we've got the drop link to take off, the bolt here, take this off, take the bracket off very
slightly, oh god I hope I have that freaking spline tool for that big thing, that's a big one
and then three bolts at the top, so I'll get back to you guys as soon as I get the drop link
and stuff off here and then we'll go ahead and discuss the top one because it looks like we're
gonna have to take the wiper arm off just to get this up so we can get to the bolts underneath
but yeah. Alright guys so we're currently up to this bit, I'm taking both wipers off,
it's very very simple, they have these little caps on the wipers which literally just pop off,
I used a little prime tool to get them off, they're up there but basically they're sitting
here on splines so you basically can adjust them when they go back on, they're 13mm nuts
and then this just pulls off, this is not bolted into at all, it just sits in there with the
seal on top. Since then I've got the drop link currently getting uninstalled, don't have my torch
on me but basically you need the spline tool to hold the thread and then you need an 18mm spanner
to undo the nut and there is a massive spline tool at the back here which I do not have so I'm
to either order one or borrow one from a friend to get that off and then yeah this is how far we
are, I'll go ahead and catch up with you when I get some more bits off. Got the drop link off,
got this nut out, thankfully the impact guide came out and obviously the whole side is off as well
so I'm gonna go ahead and take this little bracket off and then undo the top ones
I'll have to get a new bolt for that and from that I don't really know what to do next
so we'll just have to have a look around and it might be a choice of dropping maybe the
track rod end or something to hopefully drop this down a bit more so we can get this dry out.
So got that bracket off now and I'm just currently getting the track rod out,
I've also done the bottom ball joint is out as well so I think this strut is the only thing
keeping the wheel or the disc and stuff up so once I get rid of this track rod end I reckon
just give it a good wiggle and a couple of whacks here and there and hopefully this will all drop.
Okay guys so a bit of a jump, basically I completely finished doing this side
in the end I couldn't really do it on my own I had to get some help and get it done properly
because the strut wouldn't come out from the hub and it was just been a bit of a nightmare
but these springs are 30 mil now I don't know if this has bloody changed at all really but
what I'm sort of wishing and whatever you want to call it is that because this side's not done
the other side won't drop sort of thing but as well as the settling periods it's just one I'm
going to change this one and then if it goes down a bit it goes down a bit if it doesn't go down a
or whatever at least I've got new springs and then maybe in like another year or two
I'll get some coiling. So I'm gonna go ahead and get this side done obviously the rear is done now
the rear has actually made a lot more difference as you can see like the tyres are actually inside
the arch a bit than the front so far anyway but with the rears I did both rears at the same time
and they went down at the same time so that might be the cause but this one
obviously I feel that it's always on the driver's side because I don't know perhaps maybe on the
driver's side with having you know the steering wheel steering column the the actual fuel cap
and all the mechanism inside that might actually weigh this side down a bit more than the other
side so this side looks to me it looks a bit lower than the other side but again I've like
even my Clio when I've done the springs on the Clio it's exactly the same situation once I was
a bit lower because and it was always on the side where the fuel tank is and whatnot so yeah I'm
gonna go ahead get this wheel off jack it up get ready to bang off this strut I'll do it I'll
continue the video once I get everything in the same sort of position that we had it in when I left
you guys yesterday on the other side so this is where we're at got a hub down got the struts come
out next everything's disconnected currently getting the bolts out the top and uh yeah we're
gonna have this out in a minute all right so got the strut and the vice gonna go ahead and get the
gun on it take the spring out probably grease up all the bearings inside just clean it all out
and then go ahead and get the new spring on got the spring on got the spring compressors on just
got the nut on the top mount so I'm gonna go ahead and undo the spring compressors and then basically
******* ready to go back on really the spring's all in place you can see there's a little stop
point and this point well there's a little stop point I don't believe anyway cool okay lads so
considering I'm on my own pretty damn proud of myself got that in got this one in anyway
and uh yeah we are good we're getting there like I've literally just done up this bolt here
um and then we've got the three on the bottom drop link tighten this back up and uh
set this up on there and then we can drop on the floor and see how we look bring it outside
and uh see if it's all worth it oh what a job this has been okay guys so that's it now
springs in everything's all tight I'm gonna go ahead and put the spacer on
everything's all lubed up everything should be mint so I'm gonna go ahead get the wheel over
there that's my next video there I'm not gonna bother hardening it it is what it is
bricking is cooler we know we're around sending this ---- so uh yeah let's go ahead and get this
wheel back on okay guys so this is it this is the end result obviously I am hoping that these
are going to settle and be just maybe like that much slower at least um like I said these are 30
I mean you can tell it's gone a little bit a little bit lower but it's just not enough
for me to be like yeah but I mean I'm happy with the back back is a lot better
like I said this side seems more more always more lower than this side but
I don't we'll just kind of let it settle obviously the uh next job is uh getting the
intercooler on so that's going to be bump off lights off everything out front and get it all
going but uh yeah but uh yeah guys I'm going to end the video here I hope you guys enjoyed this
little uh chaos video because it's been a little bit of a nightmare doing this but
hey it's done now so like I say I'm going to put leave this on the floor try and get the springs
to settle a little bit more I've just taken up the road and back a couple of times so
but yeah hope you guys enjoy this video like comment and subscribe and I'll see you guys in
the next one peace
