LS3 V8 Miata Build - Project Thunderbolt Part 11

Tom's Turbo Garage
2 followers
1 Video ViewยทNov 16, 2022
In this episode, air, fuel, spark, fire. Let's go!
In our last episode, we finished up the bulk of our big wiring job,
plumbed our coolant hoses and lines, added some chassis braces, installed suspension and brake
upgrades, and then cut, welded, and cut some more to build the front section of our exhaust.
The finish line is in sight now, so let's get to work!
Today we're starting where we left off, by fabricating the rear section of Thunderbolt's
exhaust system. To build this setup, I'll be using the many bends that I have left over from
Summit Racing's Rod Builder kit, and a variety of high quality accessories that offer great fit
and excellent durability. I mentioned last time that I had a very specific sound in mind when
drawing up the plans for this exhaust. To sum it up, I want it to be rowdy, but not too rowdy.
Throaty, but not raspy. Deep, but with no drone. To do this job right the first time,
I went to SummitRacing.com and chose a pair of high flowing stainless steel mufflers from Magnaflow.
These performance mufflers are designed to give you more power and provide excellent sound.
They feature a large diameter, perforated stainless steel core, and a straight through
design for unrestricted flow. They come in all shapes and sizes, but I chose the 2.5 inch
inlet and outlet, 4x9 oval body version that measures 20 inches in overall length.
Okay, let's weld them on. My plan was to start with the passenger side, where I already had an
exhaust outlet hole in the bumper to reference for placement. Then I could duplicate that design on
the driver's side. This involved cutting various sections of pipe and mocking up the bends with
a muffler temporarily supported by my transmission jack. Space looks pretty tight here around the
differential, but not too bad. After making good progress on that side and ensuring that this
muffler setup would work, it was time to remove the stock rear valance in order to make provisions
for the driver's side exhaust outlet. This involved lots of measuring, a Dremel with a plastic cutting
disc, and a really steady hand, as you can't exactly ask for a do-over if you mess this up.
With the valance cuts made, I made a matching cut in the bumper cover.
The Dremel made pretty clean cuts, but a little filing was necessary to clean it up.
Now it's time to choose a set of exhaust tips. As you can imagine, I spent, oh, I don't know,
a month or so thinking about the design and placement. After all that deliberation, I chose
a pair of Summit Racing stainless steel exhaust tips. These highly polished tips are a great value
and come in many sizes and configurations. I chose this weld-on version that has a 2.5 inch inlet,
3 inch outlet, and a slanted and rolled edge. I used one of these on my Gallant VR4 build last
year and it still looks great. Now that I chose a tip, I can start to mock it up and get an idea
of how I can place it back here. So after trying out a few ideas, I ended up with this design,
which uses these universal exhaust isolators bolted to a factory hole in the rear frame.
Once I get the final placement sorted, I weld them to the frame for good.
Now it's time to tack weld the hanger to the muffler. After that, I removed the muffler and
welded up the hanger off the car. So here's a look at the passenger side in place. I then repeated
the same process on the driver's side. I tell you, after all of that, I need a break. Back to work.
Next, I pulled everything off the car to be welded together for good.
I started by welding the Summit Racing V-band clamps in place. They'll make removing the rear
muffler section a breeze and they give me the option of running more than one rear exhaust setup.
I can have a mild, wife-friendly design for date night, or I can easily switch to a louder,
wild setup for solo runs to the grocery store for peanut butter and chicken nuggets.
So after tons of welding, cutting, mocking up, and even more welding,
here's the completed front to rear exhaust section. I'm happy with how this turned out,
so let's bolt it on and finish this exhaust. One change that I made a little later on was
adding V-bands to where the front pipes connect to the headers. The slip fits were okay and provided
loads of clearance, but I just found them to be a hassle to work with. V-bands up here make it much
easier to install and remove this piece as needed. Once I had the exhaust section in place, I added
this modified differential brace back into the mix. I needed a little break from exhaust work,
so I spent some time reinstalling most of the interior. I decided not to bore you with shots
of me finagling all the stock interior bits in place, so I'll just jump to the best part. Bolting
the seats back in. These have been in storage for about eight months, and this plastic wrap kept
them dust free and looking great. Okay, back to the exhaust. I wanted the car's weight on the
suspension in order to help line up the rear mufflers and tips, so I bolted on the stock
wheels and tires, perched the car on some wood blocks, and let the suspension settle for a bit.
Then I torqued down all the necessary suspension parts to factory specs.
After that, I reinstalled the rear valance that now supports two exhaust cutouts instead of one.
So using the magic of video, here's both mufflers installed and hanging on their own.
Now it's time to weld up the exhaust tips. I must admit, I'm really picky about well-placed
exhaust tips. Thanks to this, I spent an embarrassing amount of time cutting, fitting,
eyeballing, and repeating the process until I got the exact placement I wanted. Again,
I started with the driver's side and then worked on the passenger side. After tacking them in place
and finished welding them on my table, here's a look at the finished product. Alright, let's bolt
them on. Yes! Now that is the look I'm going for. Next, I thought it would be good to give the fuel
filter a little extra protection, so I whipped up this simple heat shield, lined it with adhesive
protectant, and bolted it in place. So here's a look at the complete front-to-back exhaust system.
This part of the project took a big chunk of time, but it turned out exactly how I hoped it would.
Now let's finish up some more tasks so we can hear it. I've done enough lurking on the LS1 Tech
forums over the years to know the importance of a catch can when running an LS engine.
So to handle the important job of keeping the intake path free of oil,
I picked up this Moroso universal air oil separator from Summit Racing.
As with the Moroso oil pan that we used earlier in the series, I was really impressed by this piece.
It features a polished billet aluminum body and all the fittings and brackets needed to install it.
Moroso offers vehicle specific versions of these too, so check Summit's website for your application.
After lots of head scratching, I found a great spot for it and modified this bracket that was
part of the old four-cylinder engine. So here's all of the parts needed for our installation.
The air oil separator, the hose and drain fittings, some thread tape,
a length of hose, and our mounting bracket. Alright, let's install it.
With the unit mounted, we can run the lines to it. On the LS3, they're right near the throttle body.
You can use worm gear hose clamps, but I had some of these laying around and like the easy
installation and factory look. Next, to keep the hoses from flopping around, I cleaned up
these old Mitsubishi clamps that I found in an old bin and put them to good use.
Oh yeah, that looks right at home right there. With the wood blocks out from under the tires
and the suspension settings zeroed out until I can get to a proper alignment shop,
it was time to sit the car down on all four wheels for the first time in almost nine months.
Here's a look at how everything measures up under the hood, as everything is in place and
mounted for good. Shortly after this, I filled up the oil and primed the engine to pre-lube everything
following Chevrolet Performance's instructions. Now it's time to fill up the cooling system.
I'd read about many LS engine swappers struggling to properly purge all the air out of their
cooling systems. This is often because the radiator fill can't always be in the highest spot, which is
likely to trap in air and cause all sorts of trouble. I wanted no part of this, so I brought
out the big guns. First up, aiming the front end to the sky. Second, the UView Air Lift Cooling System
Leak Checker and Air Lock Purge Tool Kit. This OEM approved tool is widely used by dealership
service departments and allows you to perform a leak test, eliminate air locks, and refill the
entire system, including the heater core, in less than two minutes. It's incredibly easy to use. You
just connect the gauge and fitting to the coolant fill neck, attach shop air, and it sucks all the
air out of the cooling system, allowing you to check for leaks. If your system holds vacuum, that means
there's no leaks and you can route the suction hose into a big jug of coolant. Turn the valve and bam,
the cooling system is completely full with no air locks. I was a little skeptical at first, but man,
this thing worked great. One more job I wanted to complete before turning the key for the first time
was making a set of air conditioning lines. This can be a major hassle on any custom engine setup,
so to get a big jump on the process, I picked up Flying Miata's V8 AC Line Kit. As you can
see, there's definitely some assembly required here, as you'll need some fittings brazed onto
the lines. After getting turned down all over town, I found an awesome old school hot rodder
at a machine shop to help me out with this. Once I had those fittings brazed together, I could make
the rest of the line assemblies using crimp connections. I'd never done this before, but this
line crimper tool made the job pretty easy. Here's a look at my finished high side line,
and now the low side line. I think that turned out pretty... wait, wait, one gold fitting. No,
no. All right, that's better. With the AC lines finished and bolted on, it's time to pour in some
gas, take care of a bunch of other tasks like bleeding the clutch and brakes, connect the
battery, and fire it up. All right! As much as I wanted to celebrate this moment, I was busy
looking for leaks and listening for strange noises or any other potential problems. Thankfully,
everything went smooth, and there was only the typical smoke that comes from residue burning
off of new parts. After checking everything closely, it was time to make old Thunderbolt
look like a car again and bolt on the front end, starting with the fenders. The hood is on for the
moment, but just for test fitting purposes. More on that in a bit. At this point, reinstalling
dirty splash guards would be kind of silly, so I gave those a good cleaning too.
Now the bumper cover goes back on. Hey, where did that hood go? You've seen me tackle a variety of
jobs necessary to fit our Z06 intake. Well, this is the final piece of the puzzle. Installing
arrow catch hood latches and making room for the intake snorkel under the hood. Let's get to it.
The first step is to protect the hood with plenty of tape and some blankets and towels to rest on.
I've already made my reference marks when I had the hood bolted on earlier, so the first step is
to drill a locating hole there. Next, using the locating holes we just drilled and the included
templates, I measured the placement and laid everything out for good. I must admit that I
desperately needed my wife's help for this crucial step as she has a great eye for this kind of thing.
After determining the final placement, I traced around the template and started making the
necessary holes and cuts here into the front portion under the hood. After those nerve-wracking
moments, I filed any rough edges and then drilled the arrow catch mounting holes. Hey, that's not
too bad. Now it's time to mask everything off and give the underside of the hood a few coats of
titanium metallic paint. Once that dried, the arrow catch latches can be installed for good
and the hood bolted back on. If you haven't seen these before, they're an excellent design,
giving you the benefits of hood pins without a giant pin sticking up through your hood.
They can also be locked and you'll never forget to latch them because you'll see them sticking
up like this from behind the wheel. One more finishing touch addition to our engine bay are
these hood struts that I picked up from Flying Miata. They're included in the Z06 intake kit,
but they can be purchased separately and are a great upgrade to any Miata.
Installation is easy. You just unbolt a couple fender bolts, replace one of your hood hinge
bolts with the included bracket, and then attach the hood struts on both sides. The end result is
a very clean factory look and no more clunky hood prop to deal with. They also raise the hood a
little higher, giving you more room to monkey around under there. Okay, now we're ready for the road.
Alright folks, here we are on our first real drive. Thunderbolt hits the streets.
I've been putting around my neighborhood, you know, just to get a feel for things and make
sure there's no major problems or things I should be aware of, and that went well. So this is the
first time I'm out on the road getting some speed up here. You know, when you're trying a car out
like this after having it completely tore apart like we did, you know, you're just listening for
any strange noises, any strange smells, vibrations, rattles, squeaks, anything like that. So as much as
I would like to enjoy this time and, you know, celebrate, I'm really sort of tense and nervous.
Alright, well this is all gone well. I'm gonna head back to the garage
and put it up on the lift, check everything over, do our first oil change, and then from there I plan
to take it to an alignment shop, get that all sorted out, get the wheels and tires that I'm
gonna run on, and then we can do the rest of the break-in miles, and I'll get back to you and let
you know how that all goes. Back here in the garage, I can collect my thoughts and I have to
say that I'm thrilled that the first drive went so well. I set my expectations low in case I had any
problems, but the only issue was finding that the brakes will need to be bled again.
So now I can take a close look at everything, check every nut and bolt, and then drain the oil
and inspect the oil and filter to make sure that the new engine is good and healthy. Once that all
checked out, I added a fresh jug of oil and headed out for a much-needed alignment at my favorite
shop, European Auto Garage in Knoxville, Tennessee. In addition to their top quality service, EAG also
hosts a quarterly cars and coffee event which attracts an incredible mix of new and classic cars.
Once the alignment was finished, I took a nice long drive as there are still plenty of break-in
miles ahead of me. Thank you for watching and thank you to Summit Racing for helping to make
this video series possible. Thank you also to V8 Roadsters and the folks at Flying Miata for the
great products and fast technical help. In the next episode, I'll put some finishing touches in place
and show you how Thunderbolt turned out. For lots of pictures and details on this build, check out
my website at V8Mazda.com. So with that said, thanks again folks. We'll see you next time.
