Build YouTube's Best DIY Lounger – Time, Cost & Steps!

Handicraft
4 followers
2 Video Views·Dec 9, 2024
Hey, we're building outdoor furniture again. You saw me build this, that, these,
and now you're going to see me build this all next on Home Pro Hero.
So all we're doing today is building the lounger. If you stick around to the end,
I'll tell you exactly how much it costs and how long it took me to build it.
The lounger is actually going to be exactly built like the couch and the chair I built last year.
If you want to know how to build those, check out the playlist.
Step-by-step directions including the price.
Hey, the tools you need for this project, tape measure,
compact, chop saw, or a circular saw if you don't have one.
Just like the screws, the lumber package is easy too.
I need nine of these two by six by eights. I need two of these two by two by eights.
That's all you need.
It's all cedar tile. I buy it from Menards.
It's basically a green treat, but it's just brown in color.
Hardware is real simple. Two boxes of screws.
One are two and a half inch deck screws. The other ones are two and a half inch trim screws.
I got a four inch black hinge, and of course, my trusty friend, liquid nails.
So I determined exactly what I needed for this project by my design on SketchUp.
Then I used CHAT GPT to optimize my cut list so I had the least amount of waste as possible.
I got different boards or different cuts out of each board.
I'm going to follow that list and make all the cuts all at once,
and then we'll assemble the chair.
Cutting everything at once, thanks to CHAT GPT.
Last cut. Hope it all goes together good.
So let's split the stringer board 74 and a half inches.
We're going to cut it in half. I'll show you why here in a minute.
Let's assemble the lounger chair. It's real quick, and it's real hot out here, by the way.
I'm going to use liquid nails or all joints just to make this thing nice and hard.
Don't go nuts on it, just enough to keep it a little tighter than just having screws alone.
That's pretty much it.
Okay, I'm using these two and a half inch trim head screws.
The reason why trim head, they're smaller heads than deck screws.
I use deck screws inside of the lounger,
but on the outside I use these deck screws just because they got a smaller head,
and they're not as visible.
So when it comes to the stringer boards,
those are the boards that will actually hold the flats so the mattress pad can sit on top of.
And then I'll attach the stringers using screws and liquid nails.
No space under the stringers, right?
Straight on the ground.
That's going to give you the inch and a half on top of the stringers,
plus a little bit of reveal so the pad sits down in there.
I don't want my pad blowing away in a windstorm.
So I want that thing sunk in there, and I think it'll look better too.
So let's move forward.
No spaces underneath.
These strings are straight to the bottom.
I did the math for you already.
You basically got to put an inch and three quarters in between each two by six boards.
You can put six slats in between at one and three quarters.
I'll liquid nails, and I'll use regular deck screws for this
because the screws won't be seen underneath the pad.
Okay, with the legs, a little complicated cut here.
Nothing major though.
You can put notches on both sides.
All you got to do is use an existing two by eight.
I use a black marker.
It's easier to see.
Cut those lines.
All right, let's move the arms real quick.
Pretty simple.
Two legs, the one leg that I cut already, and then this leg.
They're both 12 inches tall.
All I need to do is put some liquid nails on top.
And we'll probably put three, maybe four in the top here.
Hopefully this will all fit together nicely.
Make sure the common board, which is the half moon, is downward here.
Okay, got the legs ready to go on.
We'll put it up this way first.
The thing you have to worry about are the backs.
Make sure you're nice and tight against this back board here.
Make sure this part right here isn't overhanging into the frame area.
You want this to be thrust.
So if I feel it, it feels good.
I'll put the first one in.
Now what we want to do is make sure the back leg's square.
I'll move this out of the way.
I don't need it anymore.
You see right now, it needs to come down a little bit like that.
Right there's square.
So then the front leg, same process.
You want to use a square.
You can see right now is that this leg's tilted forward this way.
Scale it back until this is nice and tight.
If it is there, we're good to go.
Hey, if you like these types of videos
and you like to improve the value of your home and your property,
just subscribe to the channel and get it over with.
It's totally free.
It's on me.
Okay, we're on the home stretch now.
Gonna knock out this backrest real quick.
I'm using 2x2 cedar tone for the back frame.
And then I'm using the regular 2x6 slats that I used on the bottom part of the chair.
The only difference being that I cut them a half inch short.
So I'm about 25 and a half for the backrest.
The reason why I did that is so that way when I raise and lower the backrest,
it actually fits in the groove nice and snug and not too snug.
The back frame is about 23 wide, about 30 long.
My pad's 80 inches long.
So the front part of the chair is 50 inches
and the back part of the chair is actually 30 inches for a total of 80 inches.
It all depends on the size of your pad.
The big thing to keep in mind here is to make sure I have the room
for the 2x6 jack stud that holds up the backrest.
It's about five and a half inches.
So those middle 2x2s have to be pretty close.
I think I ran them about six inches.
Here I am installing the hinges real quick.
I've got three of these four inch black hinges.
Regular door hinges, no big deal.
I just butt the upper part and the bottom part together and apply the hinges.
Now the back stud, not tricky at all.
I just centered that back hinge.
That 2x6 stud is actually level with the bottom of the backboard.
You'll see here in a minute, I'll add the brace to keep that backboard
from having too much stress when it's not in use.
Quick little trim piece across the back using liquid nails
and the regular trim head screws I use for the rest of the project.
Finishes out the space real nice and neat.
So I decided to go with the armrests on the lounger
because my community poll I put out there,
the majority of the people that voted wanted the armrests.
Should work great for drinks.
Here's that bottom brace I was telling you about.
It doesn't have to be anything special.
You'll never see it once the chair is upright.
This thing weighs a ton.
Had to get the reinforcement.
The boy was home.
I snagged him and we got her to the back.
Just like that, you've got a laundry chair
that's going to match your furniture that you already built.
Finally, the lounger's done.
Time for some R&R.
Nice cup of coffee on my new chair.
Hey, this is a nice spot for the lounger.
That master bathroom remodel done yet?
I guess I'll enjoy the shade in the Pavilion Smokehouse
on the matching sofa I made last year.
Let me show you the lounger real quick.
It's a super simple design and easy to build.
The lounger is roughly three foot by seven foot
designed to fit a 26 inch by 80 inch pad.
It's a low profile memory foam that keeps you cool.
The backrest has three different positions,
but more can be added if you want.
So what do I have in it?
Took me about six hours over a few days.
I'm all in for just over $200,
but you can definitely go cheaper
by not adding the armrests around
or actually possibly going two by four construction
instead of two by six.
But I love the big bulky look of the two by sixes.
Plus it matches my other furniture.
The plans and all the products I use
are in the description below.
Hope you enjoyed the video.
Give me a big thumbs up.
Take care and I'll see you next time.
