Kitchen Remodel Full Time Lapse DIY Friendly

ZEM Construction
5 followers
12 Video Views·Nov 3, 2022
Kitchen Remodel Full Time Lapse DIY Friendly
Hey guys, Zach here with Zim Construction bringing you another remodel video.
In this video, I'm going to show you all the steps that I took to take this space here,
bring in all new cabinets, countertops, tile backsplash, flooring, appliances,
and updated plumbing fixtures, and turn it into this beautiful kitchen here.
I want to take a minute and thank you so much for taking the time to watch this video.
If you like these types of videos, I would really appreciate your subscription.
I post them as often as I can. Some remodels do take a little longer than others,
so if you could hit that notification bell and be notified when I do post a video,
then you won't miss out.
So here are some before pictures. You can see there's a little bit of water damage,
also a little bit of excess wear and tear. So the homeowner and I decided that would be a
lot more efficient and cost effective to rip out those cabinets and replace them with all new ones.
The entire design of this kitchen is based off of pictures that the homeowner gave me
from Pinterest and Google. I really enjoy working off of inspiration like that because then
it also allows some creative freedom on my part,
but at the end to give them the overall look that they are going for.
This property is an income property. It is a rental, so they will be renting out the entire
space. So a nice, clean, updated kitchen is a great way to get quality tenants.
So the first step was going through and scraping off all the caulk lines and excess buildup that
needed to be removed. Some of these places are going to be recovered by cabinets,
but there are a couple spots that aren't going to be filled with the same size and types of
cabinets that were there before. So I went through and scraped those all off and then
went through with a spackle. I think an all-purpose mud would also work here,
but I think spackle does dry a little bit harder. So because of the durability that
was desired for this space, because it is a rental property, I chose to go with a spackle.
Went through and sanding those things flush. I am going to be spraying a orange peel texture,
and that is something that I do hear often in the comments is how much people do not like
the texture that we choose. This is a thing that is regional depending on where you live.
There is different standards as far as what people like, and up here in the northwest,
an orange peel finish is very common. I also wanted to make sure that I match the rest of
the house and keep that cohesive. Because I am going to be using a spray texture hopper,
I went through and masked off everything. I use an inch and a half blue painter's tape,
as well as a nine-inch roll of paper with a hand masker. Then for the long plastic sheets,
I use a 3M 72-inch plastic. One trick that I like to use, especially when going over
pre-existing paint, is when you spray texture mud, it does not have the best bonding. So in
order to get good bond to the previous layers, I actually mix the texture mud with a high bond
primer, and sometimes even a one-to-one ratio, and use that to spray onto the wall so that the
orange peel does not flake off later because of an inferior bond to the lower levels of paint.
There was some inconsistencies in the previous texture, but also I wanted to cover up some of
those patches that I filled in earlier, so I just re-textured the entire space.
So now I am going through with a Graco X7 airless paint sprayer. It is a great tool to use for both
interior and exterior painting. It does spray a lot of paint, and there is quite a bit of
overspray, so that is why I took the time to make sure everything was masked properly.
Again, the colors were chosen by the homeowner based on some pictures that they had sent me.
Because of the texture, I did go through and hit everything with a roller real quick,
just to kind of push any excess paint into some of those deeper grooves and textures.
One thing that was a little bit unique in the design that she had chosen was that she wanted
to do a darker ceiling. It is not something that I am very familiar with, but that was something
that she has done in her own house and wanted to replicate that in this space.
I told her it would not be an issue. So after all the painting and
wall prep was done, next was the cabinets. We went with a contractor grade cabinet.
Again, because this is a rental property, cost was a factor. So we did not want to go
too crazy and spend a bunch of money on the cabinets, but these are great quality and will
last. I did add a vent there for a microwave hood. There was a little bit of a spacing issue with
where the hood goes, so I had to add a little bit of a spacer on the far left to make sure that
that vent did go through the middle of that cabinet. There was an outlet there, as you can
see, where the old microwave was. So I just, when I did install the microwave, you will see later,
I just kind of ran the cord through there. It worked out great. One tip that I could give you
when installing cabinets is when I screw them to the walls, I do not actually screw them in all
the way. I kind of leave it a little bit loose for adjustment. So that way when I put the face
plates together, I can make sure those are perfectly square and straight and flush, screw
those together really tight, and then I go back and tighten all of the screws that are into the
walls, and in this case, up above on the soffit. I also like to do the upper cabinets first,
just to get them done, and I don't have to worry about working around the base cabinets that would
be in the way. So after all the uppers were up, brought in all the lowers and getting those
installed. One piece that we did want to go with was a Lazy Susan. The Lazy Susans are a great way
to use space efficiently. However, they do come a little bit smaller than the depth that normal
base cabinets go. So with that, you got to add a little bit of a wall on the back to support
the countertop. So I did a little wall here and also did a cleat on the back of the wall so that
the countertop had a nice flat level place to sit on. I just used some standard 2x4s to create this
wall. I did a normal base plate and a top plate just like you would like a traditional wall.
I wanted to have lots of support for that countertop. Also along the back of this,
I'm going to be adding a quarter inch panel. So I wanted to have lots of support so that
that panel would be nice and strong. In here, you'll see that I put one vertical support,
but I do end up going back and adding two more in the spaces to give it as much stiffness as possible.
I also put a cleat along the back just for some added support behind the dishwasher.
So after the cabinets were installed, the next step was the laminate countertops. Again,
we chose laminate because of the cost effectiveness as well as the durability.
One tip I would give you when doing these countertops, you can actually buy the pieces
at this size from your big box store, Home Depot in this case, but always check for square. These
pieces were completely out of square and it took me way too long to figure out what was wrong with
my measurements. It just came from the factory that way. So I trued up one edge and it made
rest of the install go significantly easier. I did go with a spacer underneath all of the
cabinets to give an inch and a half reveal for all the countertops. As you can see,
I'm putting those blocks on here. Those spacers only need to be in places where the countertop
will be attached to the top of the cabinet. Also, because this house was empty and there
are currently no tenants living in there, I was able to utilize several of the rooms as
workspaces. This is a great place to have a nice big flat space to create that large single piece
countertop. I did have the spacers overhang a little bit so that I could go back with a flush
trim router bit. In this clip here, you can see I'm using the cordless DeWalt router. It is a
great tool. I'm really glad I did it. I didn't have to worry about a cord all over the place.
I use it in several different places, especially at this countertop, but using that flush trim bit
gives a really nice flat reveal and gives a great place for the laminate to stick on.
The next step was getting the sink cut out. Most of the time, sinks do come with a big template
like this, so I just found the center, put it exactly where I wanted to, lined up with the
window as well as the lower cabinet below, taped it in place, and then went through with a pencil
and just traced it out. Because the cabinets were new and the countertops were being replaced and
all put in, I did use that to my advantage and I was able to pull the countertops away and make
the cuts and even installs, as you'll see later, without having the countertop fully installed.
Here I am cutting out the sink hole with, again, another cordless DeWalt tool. As you'll see,
a lot of the tools that I use have that yellow coloring to them. I'm a big fan of DeWalt and
really like their batteries and the flexibility between the 60 volt as well as the 20 volt.
There I am checking the fit of the sink. I did go and order a 12 foot by 5 foot piece of laminate
so that I did not have any seams. It is something that you have to special order.
So as you can see here, I'm actually cutting the two inch strips for the edge of the countertop.
So I cut those off first so I could use the factory edge. I just used a straight edge piece
trim and the router. I found that using a router, even though you're doing a straight cut, is one of
the best ways to make those cuts. So I like to put the edge of the countertop on first so that the
reveal of the laminate is on the side as opposed to putting the top on first and the edges last
because then you'll see the reveal on the top of the countertop. So I hope that makes sense, but
whenever I do laminate, I like to do the sides first. Also keeping in mind which
section of the countertop is going to be seen most because laminate does have a dark reveal
like I mentioned. So keep in mind where that dark reveal is and be strategic about where you place
those edges. There are three sections total with large L shape with the sink in it. As you can see
here, I'm getting those flushed up and ready and then also the two smaller sections that were on
either side of the stove. Again, this cordless DeWalt router made quick work of this process.
Highly recommend it if you are in the market for a new router.
Also, that tool and any of the other tools that I use, I do have links in the description down
below. They are affiliate links and they don't cost you any more money, but it does
support this channel if you do use that link. So if you are in the market again, I'd greatly
appreciate it. So I used a spray adhesive, countertop adhesive for the edges, but I did
with a roll-on contact glue for the top. So the process is just do a nice heavy coat on both
sides of the countertop. Let both of those dry to the touch. On the particle board side,
I actually did do two coats. I felt like the particle board is pretty absorbent,
so I wanted to add a second coat to make sure I had a good layer for a good bond.
Again, using one of the spare bedrooms as an extra workspace. It was pretty cold outside,
so although I could have done it outside, I was a little worried that
using the adhesives outside would cause issues for the drying time.
So once the two sides of the countertop and the laminate do stick or touch, they are stuck
together forever. So you can see me using some dowels there as spacers so I can get the top
layer of the laminate lined up. Then once it's lined up, I can slowly carefully pull out those
dowels and make sure that the laminate is lined up properly. Go back with a nice little J-roller,
push down, make sure that there's a good solid bond. I would recommend, if you can, get a partner
for some of the bigger pieces. I did prepare myself and was able to do it alone, but it would
have been a lot easier with someone else. But again, once everything is lined up, you can just
go through and slowly pull the dowels out, continually make sure everything is lined up.
And again, I went back and rolled it all with a J-roller. Again, using that router with a
flush trim bit was awesome, especially on large pieces like this, not having to worry about the
cord. I could go around every single side of the countertop very, very easily. Now I'm getting
those countertops installed. Again, kind of like I mentioned earlier, it was so nice being able to
pull the countertop away and do the install. I highly recommend, if you ever are doing a new
sink, if you can, install the faucet before putting the sink in the countertop. It's a lot
easier to make sure everything is tight and straight before dropping the sink in. Again,
I also attached the sink to the countertop before putting it in, again, allowing it a lot more space,
make my life a little bit easier to put those clips and attachments in.
Get everything lined up and pushed in. Then I went through from underneath and screwed the
countertop in from the bottom. So after the countertop was in, the next step was doing
the tile backsplash. So this is a three-inch by six-inch subway tile backsplash, again,
going off of the pictures that the homeowner gave me. I'm sure I'll get a little bit of grief in the
comments for this. I did go with a tile adhesive. I know that tile adhesive is not the best product
to use with tile. In my opinion, there are certain cases where it is okay because it is quick and a
tile backsplash is one of those cases. There's not going to be excess water hitting that backsplash
and so using an adhesive as opposed to a thinset is going to be okay. However, if you are doing
something in a bathroom, especially a shower or a bathtub, I highly recommend using a thinset and
not a tile adhesive. Again, this is a very specific case that I think it'll work, but it is not
something that you should be using for all cases. As you can see, I try to use a masking tape wherever
I can just to make cleanup significantly easier, a lot more straightforward. A little bit of planning
when installing tile does go a long way. You can see my little stack of half tiles that I had there
so I go through and easily do that subway pattern very, very quickly. One thing when you're
expansing across a gap like where the stove is going to go, you want to make sure you add a cleat.
The homeowner did want to use, as you'll see later, a white grout. Because the grout was
just going to match the tile and there wasn't going to be a high contrast between the actual
tile and grout color, I just used the space that the tile provides and not used spacers. If you
did want to use a darker grout for some design aesthetic, I would recommend getting an eighth
inch spacer and putting those in between there. It allows for a little bit of a thicker grout line
and gives it more of that contrast. Again, because they were going to match, I didn't feel like it
was necessary. The tile does have a little lip on the edge so it allows for a 16th inch space
between each and every tile. In that case, it worked out. I did use an extra piece of the
countertop as a spacer along the bottom so that I could have a nice caulk line. Here I am putting
in that non-sanded white grout. Again, because this is a 16th inch space and not an eighth inch
space, I had to go with non-sanded. If you do have an eighth inch space or larger, sanded works great
in this case because it was just a thin space. Non-sanded worked. After the tile was put in,
next I moved on to the floor. As you can see, I did not pull up the pre-existing linoleum.
That was something that the homeowner and I talked about. They had decided that they didn't
want to remove it and they didn't want to pay me what I had asked to remove it. Because this is
how I feed my family and my time is quite valuable to me, if I'm not going to be paid for something,
then I'm not going to do it. I know that would probably be the better step to take, but we are
using an LVP click-together floating floor system. There is no adhesion or anything to worry about
in that case. As long as the floor underneath is flat, there is nothing wrong with putting
an LVP over the top. That's what we decided to do. This is a great product for kitchens,
bathrooms, basements, living rooms. It's 100% waterproof. The technology has finally caught
up to the flooring industry. It is also very straightforward to install. It does take a little
bit of practice, but the click-together is a great option. There also is glue-down
and peel-and-stick flooring that I think in this case would also work. Again, up to personal
preference. Each one of those does have a price difference as well. I did put some of that new
flooring in the landing leading downstairs. Again, speaking to the versatility of this product,
it really can go anywhere, even on steps like in this case. What's also great is that if any
piece is ever damaged for any reason, you can simply just pop out that piece and replace it
with a completely new one. After all the flooring was done, the next step was to go through and add
the toe kick to underneath the cabinets. Because these cabinets are from Home Depot,
you can go down the same aisle and buy the matching toe kicks as well as any other spacers
that are already painted to match. After the toe kick, I went through and started adding
the baseboard and door trim. Most of the trim was around the windows and the doors I just kept and
patched any places that needed it, but because they were ripped out previously, I did have to
go through and replace all of the baseboard. Another DeWalt tool that I would highly recommend
is their cordless 18-gauge brad nailer. It works so well when doing trim work like that,
and not having to worry about the air compressor and the hoses and the cords that come along with
is incredible. Now I'm putting in some of these light fixtures. I went with a very thin flush
mount light for over the top of the sink. In a perfect world, we would have done a recessed
light there, but because of the previous light that was in, it would have made life a lot more
difficult, so I just went for the extra cost of a flush mount. The last step is just to go through
and get the appliances installed. So you can see that vent that is there because the microwave that
I'm putting in does have an integrated vent hood. Kind of like the sinks, these microwaves do have
paper templates that show you exactly where to put the screw holes, and the mounting brackets
makes installation very easy. And you can see I ran the cord through that first cabinet,
push it through the other side so it would be plugged in. Because I had the holes pre-drilled
and lined up exactly, it made installation very, very simple. After the microwave, the next step
was to get the oven installed. This is a gas oven. I would highly recommend if you are installing gas,
make sure you use a leak detection fluid. In this case, the oven actually came with one,
and I was able to test all of the joints, make sure there were no leaks. But also, if this is
something you are uncomfortable with, it is great practice to call a professional. In most cases,
the places that you buy the appliances will install them for you. If not, they will more
than likely have someone you can call to install them properly. Do not take any chances of this
type of stuff if you are not comfortable. After those two were installed, I went through and hit
all of the trim with a nice white paint. I was sure to get the matching color of the cabinet
so I could paint this back panel here, as well as do any touch-up work that any of the cabinets
needed. So I added some paint in some of the other rooms for them as well. Next, I went through and
installed the dishwasher. There was no dishwasher previously, so there was a little bit of excess
plumbing and electrical that needed to be done in order to accommodate a dishwasher, which I think
is a great idea. It is another aspect that will really add some value and desire for potential
tenants. In the very last step, just to add those finishing touches, I went through and added the
door pulls and drawer pulls. Again, going with the inspiration picture that I was given on Pinterest
to give the look that they were going for. You can see I'm using a jig from Kreg. They make a
great little jig that allows you to line up the holes perfectly. It makes installing pulls and
handles so much easier. I will also have a link to that down in the description below.
Then, getting the large refrigerator installed, there was an ice machine and water supply in the
and because of the different depths in those shaker style drawers, I had to go to the hardware
store and buy new screws at different sizes in order for those to fit. Doing some final cleanup
to get ready and show the homeowner their brand new kitchen. Here is the video walkthrough of what
the homeowner saw after everything was all finished up. As you can see, we went with a white
shaker style cabinet, a laminate countertop that has a granite look to it,
a dark wood LVP flooring, all new Bosch appliances, gas stove, a very traditional
white baseboard, a gray beige wall paint, and then the ceiling was just several shades darker.
Now, I get a lot of flack for this and I say it in all my videos, but this one, again,
turned out really nice. The homeowner was very pleased. So, here are some after pictures.
At a later date, we may or may not add a little dining bench for there just to
have a little bit more efficiency and not have to worry about scooting around the table and
having chairs in the way because that is kind of a small space, but it is designated for dining.
Lazy Susan cabinet right there, a nice stainless sink, a large faucet over the top.
So, this project turned out really great. Again, I want to thank you so much for taking the time
to watch this video. If you enjoyed it, I would really appreciate it if you hit that like button,
just kind of lets everyone else know that this is an interesting video. Again, I would really
appreciate your subscription and also hit that notification bell so you are notified when I do
post a remodel video. If you have any questions or comments or anything, I would really appreciate
it if you left a comment down below. I will do my best to get to most of those and answer them.
If you enjoy these types of videos, I would really encourage you to check out the other
ones I have posted on my channel. They are all under Zim Construction. I have two basement
remodel videos on there as well as a bathroom, and I also have several more in the pipeline that I
want to post very, very soon. Again, I want to thank you so much for watching, and until next
time, we'll see you later.
