Here I show how to successfully make a simple two piece silicone block mold. The castings are made from hydrostone which were originally cast into a one-time use mold created with Alja-Safe from Smooth-On products. The Silicone Block Molds are made using Mold Max 30. I also used a Universal Mold release from Smooth-On as well. Please follow the links below to purchase these products through Amazon.com.
BOOKS – self improvement Neville – The Power of Awareness (also includes Awakened Imagination) https://amzn.to/3lYdoEk Florence Scovel Shinn – The Writings of (includes biography) The Game of Life & How to Play It / Your Word is Your Wand / The Power of the Spoken Word / The Secret Door to Success https://amzn.to/3ssh9Ey
SCULPTING MATERIALS & SUPPLIES CraftWrap - Plaster Cloth Gauze Bandage for Scenery, Crafts, Mask Art, Models, Molds, Keepsake Belly Cast - Each Roll 4 inch x 15 feet (Single Roll) https://amzn.to/3cwRvJg 1 Oz. Fiberglass Chopped Strand Mat - 3 Yards X 50" Wide for Hand Layup, Vacuum Bagging or Molding Composites with Epoxy, Polyester or Vinyl Ester Resins https://amzn.to/3fjUq9V Carriage Bolts ¼” x 20 SS, U-Turn, INC. (50 count) https://amzn.to/3lZtayK Autobody Panel & Trim Removal Tools (for demolding/separating your mother mold) https://amzn.to/3w9LXML Steel Hex Bolt, Grade 5, Zinc Plated Finish, Hex Head, External Hex Drive, Meets ASME B18.2.1/SAE J429, 1-1/4" Length, Fully Threaded, 1/4"-20 UNC Threads, Imported (Pack of 100) https://amzn.to/3ctbs3x 60 Pack 1/4" Wing Nuts Zinc Plated Fasteners Parts 1/4"-20 Inches Butterfly Nut https://amzn.to/3u31V9r AES Industries 294-1 Replacement 2-1/2" x 1-5/8" Curved Surform Blade (6 Blades) https://amzn.to/39q8efg Stanley Hand Tools 21-115 7-1/4 in. Surform Shaver https://amzn.to/3svUMhB JB Weld 8277 Waterweld https://amzn.to/3cwSZTQ Chavant NSP Medium – Sulfur FREE, 2lb Professional Clay (Green) https://amzn.to/31tVqA8 Alja-Safe Life Casting Alginate 3lbs (by Smooth-On) https://amzn.to/3wfZiDl Smooth-On Mold Max 30 (Trial Kit, pink color) https://amzn.to/3fkM41Z Smooth-On Rebound 25 2lbs (Trial Kit, orange color) https://amzn.to/3m0MuvI Smooth-On THI-VEX https://amzn.to/3ruTeTL Krylon Acrylic Spray Crystal Clear 11oz. https://amzn.to/3cvMDUU Premium Baltic Birch Plywood 6mm (1/4”) 12” x 24” by Wood-Ever (I give Woodever two thumbs up for quality birch ply) https://amzn.to/39q9XS2 Titebond Original Wood Glue, 16 oz. https://amzn.to/3sx2E2o Dental Tools / Waxing Modelling Tools https://amzn.to/3sJ4ai9 Sandpaper Variety Pack 24pcs, 12 grits: 120 – 3,000 grit https://amzn.to/3djpa8F
Music is used with permission through filmora 9 Wondershare editing software. Music by: Name of the Child - Motions Lady Lane - The Pink Everland Sky Living Pulse - The Chapman Run
Okay YouTube, so we're back for the second part of silicone block molds.
Here I'm going to show how to mix and pour the silicone.
So we have our digital food scale.
The manufacturer says to avoid this if you have a triple beam,
but it seems like the digital food scales are a little more common than most.
I wear the gloves to keep the silicone mix off my hands because it's terribly sticky
and it's easier to throw away these disposable gloves than to try to wash my hands and
use countless paper towels.
So this is a 1 to 10 mix.
They ask that you mix up this bucket before pouring it.
The viscosity loosens up quite a bit as you get to mixing it
and other than that, I don't really know other than to mix the top skin into the body
the benefit from it.
But I do as the manufacturer suggests in this instance.
Now we can pour any amount in here that is suitable for the cup.
And what I'm going to do is find the weight of this after we pour in the desired amount
in the cup, preferably not so much that we can't stir it.
But once we get it weighed, we will just add 10% of that weight onto the scale.
So we'll add 10% to the weight in our head.
And this part B here, there's a little trick to this.
So when you open this up, it's going to have a foil seal.
Shake it up before you open it.
But you just open it up like a juice can or the old tomato juice cans.
And that helps you control the flow.
And if you vent it in the top there, it doesn't glurp when it comes out.
So there's 10%.
It has a real heavy red color.
But as you mix it up, it'll turn pink.
And one of the benefits to using this transparent cup
is that you can see how well you're mixing it.
So you want to scrape the sides and scrape the bottom.
And as you're scraping the sides and scraping the bottom,
make sure you scrape your tool off on the edge of the cup
to make sure you don't have any that's not mixing against your stick.
So you can see this takes on a Nestle Quick Strawberry Rabbit kind of color.
And you just keep going.
Scrape the sides, get it going.
Usually only do this for about three minutes or so, if that.
And you'll get forearms like Popeye after doing this all day.
OK, once this is mixed up, you have the option of degassing it
if you have a degassing chamber.
Otherwise, we're going to do a method called high pour.
And this is where we pour a very thin stream
and that helps knock out a lot of air bubbles as it lands on the piece.
I found it to be very effective.
This is our universal mold release.
Make sure that you apply this.
You want to do one coat.
You do the mold release and then brush it with a dry brush
and then apply another coat and then let it dry for five minutes
and then apply another coat.
I rushed through it.
I made a mistake, actually.
Which we'll see up ahead in this video here.
But here's the high pour method.
We can see that that thin stream is actually eliminating quite a bit of air bubbles.
And you will see micro bubbles and that's OK.
The manufacturer recommends pouring at the low points
and letting it rise up over the high points.
I found pouring it on the detailed areas has always been favorable.
I don't get air bubbles.
So when we are done pouring this, we'll get to the end of the cup.
Now you can scrape the sides of the cup.
If you start to see white, that means you didn't mix it well enough
and I don't recommend scraping this into your mold.
Just, you know, cut your losses and set it to the side
because that base may not kick.
Then you might have some sticky compound after the rest of the mold is cured.
So, you know, if you see the white stuff, just stop.
It's not a big deal.
OK, we'll set that to the side.
And if you want to level it, that's fine, too.
That really only matters when you're doing a one piece mold.
It's just a habit of mine, sorry.
And I included this foot here to show you how I prepped it.
You won't actually see me pouring the rubber into it.
It would be a little redundant.
So you can see how I clayed up the wall for that
and put a little pour spot there on the side.
So anyway, we'll get the rubber poured into that
and get it back here once it's cured.
OK, so here we go.
24 hours later, we have the first side cured.
I can cut that hot glue loose with that putty knife.
Careful not to cut your hand here while you're breaking these walls loose.
If you can save the walls, that would be good.
You can reuse them.
You'll see here when I demold the foot,
it's a different situation where it didn't work for me to reuse the walls.
But try to spare them.
And right here, you can see how the rubber went up
into the corrugation of the cardboard.
If I had sealed the top of that cardboard,
it probably would not have been able to push its way up inside
because of the trapped air.
But you can see that that silicone can find a way through.
It will find a way through.
I love this stuff.
So that's the importance of doing the prep work ahead of time, hot gluing it.
OK, so the backside here, you can see where that silicone leaked under past the clay.
Just a little bit.
Not a big deal.
Actually, it turned out rather nice.
So we pull the clay off.
Careful to leave our model or our casting in this case inside of the mold.
Do not demold it yet.
Just leave it in there.
I can take that little piece and put that back in there.
And that's going to be our core spout.
So when we demold the second side, it'll leave a nice hole there.
OK, so this here, I'm just gently pulling these away
like a loose thread on a garment and popping it with the tip of that X-Acto knife.
OK, you can see where it's in the folds of the hands and whatnot.
But you can see how well I got to the parting line there
that I drew with the felt tip marker or the permanent marker Sharpie.
Before we put the walls back up,
if you would like to apply your mold release or release agent,
I typically use Vaseline.
Vaseline makes a great release agent.
It will prevent the silicone from ever sticking to itself as long as it's on there.
So you can finish getting this cleaned up and get your mold put back together.
I would recommend using the Vaseline before you put the walls back on.
You can do it afterwards too,
but you won't have the accessibility to it with the walls up like that.
If you elect to not use the Vaseline,
you can use a universal mold release made available to you from the Smooth-On company.
When you use it, make sure you follow the directions well.
I used it on this project and did not follow the directions.
Fortunately for you, you're going to see how I handle the problem
when the silicone sticks together and makes one block.
And you will also see here that as I box this up,
I do not plug that feed spout there and will cut it away.
So you don't have to have a feed spout.
Look at this.
So I put the walls back up and you can see that when I put a straight edge across there,
the wall does not work.
So I'm going to have to cut another wall taller to house the silicone
because if I were to use that wall,
I wouldn't have really any bottom and the heel might be exposed.
So here I am.
That universal mold release, I spray it loosely and very conservatively, not enough.
So I've mixed up a second batch and I'm pouring it on here.
And unknowingly for me, these two pieces are going to adhere together
and that's okay because we can cut those blocks apart.
And the serrations, I'll show you how to cut it apart using serrations.
Okay.
And we're almost done.
So we'll scrape the sides of that cup, wipe it in there.
It's a nice pink all the way through.
Kind of like a nice steak.
You pull it off the grill.
Still a little pink in the middle.
Okay.
So we have our molds.
They're cured on both sides.
And I'm going to break this loose.
You can throw these walls out.
As you pull them off, you don't have to try to save them.
In fact, they're pretty useless at this point other than to mix epoxy on or something like that.
You'll see some cardboard flashing or whatever you call it,
sticking to the silicone.
And that's not a big deal.
I mean, if you want to get a knife and scrape that off, that's fine.
But as far as function, it's not going to stop it one bit.
Okay.
So you can see here, I'm finding out that that is not coming apart.
And, you know, there's a little moment of panic like,
uh-oh, what's going on here?
But there is enough color difference between the two
because I must have poured just micro amounts different to cause a color difference
that I know where the parting line is.
And I can use that as a reference point to start cutting this apart.
So as you cut it apart,
pull and just make a lot of little cuts.
Do not try to make a clean cut.
Because all the little many hundreds of cuts,
even though it looks messy, those are all registration marks.
And that's good for the final product.
You make it one clean slice,
it's, you know, your seam lines may overlap and not be quite matching.
So just do a lot of little cuts here.
Turn the camera around so you can see what I was doing since I'm right-handed.
As you get closer to the model, you'll be able to see your parting line.
Now try to follow that parting line to the best of your abilities
so that when you have your casting in there, it'll come apart as easily as possible.
At this point, if you can get your model loose, you can pull it out.
So I had to work it a little bit, but I got the hand free.
But do not pull too hard because you could rip your silicone mold that you worked so hard to get.
You can see a little bit of rubber that's stuck in the creases
of your plaster and that's okay. That's not a big deal.
So you can see how those two pieces go back together.
And I have my little pour spout that was pre-fabbed before the pour.
So this foot is going to be a little more tricky because
I did not make a pour spout before I poured that second layer.
So that baby foot, the cast of that baby foot is somewhere in there.
Now you have to try to remember which side is up.
And like I said, there's enough of a color differentiation
that I was able to have a general idea of where to cut.
So be patient, take your time.
And I probably took well over a half hour to cut this out.
And again, once I found that seam line, I knew exactly where to cut.
So I just kept making a lot of little cuts.
And once I had the foot out, the marker actually got pulled into the surface of the silicone.
So I followed that as well as I could.
Now I'm cutting the pour spout into the piece.
I know where to cut it loose.
And just be careful.
And again, take your time.
And you will have yourself a nice pour spout
if you just think about it before you jump in there and start slicing.
So you can see how that's what my pour spout would have looked like on the foot.
And I have my pour spout.
I can hold that together with some rubber bands,
some wide rubber bands around the side and over the top.
And it will be ready for pouring into.
And so that concludes our silicone block molds.
Please like and subscribe if you like this video and would like to see more like it.
Thank you.