Climbing Anchors from the Bolting Bible

HowNOT2
100 followers
2 Video Views·May 27, 2020
Here is the Climbing Anchor section from the Bolting Bible explaining in detail all the options for how you can configure climbing anchors. Leave us comments or message us about how we can make this section better in the Bolting Bible as we update it every winter.
Another great anchor video by AMGA certified guide https://youtu.be/Y-pLP9dRWPc
Live life high... safely. All the info is FREE at https://www.hownottohighline.com/
Do you want to see climbing anchors and how they're configured?
Check it out on this episode of How Not to Highline.
Hi I'm Ryan Jinks and welcome to the Bolting Bible.
This video is going to cover what is in the chapter of climbing anchors and we're going
to show you all the different configurations you're probably going to see when you get to the
top of your climb. The most basic setup you're going to see is two bolts because
every anchor is going to have redundancy and in this situation you will have to add
your own gear into it and it's assumed that you will remove it and in the situations you
would see that is when you can access this from the top and you can walk off when you're done.
You do have to make sure that your gear goes over the edge and that your rope isn't just
rubbing over the top of this sharp rock. The other most common areas that I've personally seen it
is in multi-pitch climbing where you go up, your partner comes up, you continue,
and then your partner takes the gear with them and leaving only these two bolts.
It has a much lower visual impact when this is all you've got.
So I am fully certified in absolutely nothing so I'm not really going to try to cover
climbing anchors as a whole and how to climb but there are some basic things we can obviously
cover. We are going to put in the links in the description below and on the screen here
different things that you can resource because there are lots of great resources out there.
But for this example if we were going to top rope this and we're able to access this from the top
we would clip this quad anchor. You can do all sorts of different configurations
and in this case it gives us a little bit of mobility here without the risk of a shock load
which we are actually going to be putting out a video on if shock load's a myth. But we clipped
only three strands you can clip two and two it's all sorts of different things you can do with this
but then we would run our rope through here and top rope this and then when we're done remove
everything. Or in big walling it's kind of a good system the quad anchor for being able to clip into
all sorts of different points especially if you only have two bolts even though I personally love
on El Capitan when there are three bolts at an anchor spread out so you can like kind of have a
second party try to go by you or something it makes it nicer. But anyways let's show you the
next configuration. Chains are another option to equalize two points in different ways or to go
over an edge. We're going to show you here that when you put this on you want to flip it so the
nut is screwed down in case it jiggles it's only going to ever screw down. If it was the other way
and it over time jiggled it could jiggle open. Okay now that I've installed these I will want
to either wrench down this nut or add a thread locker sealant in order to make sure this doesn't
naturally come undone. Now you want to make it pretty hard to remove this stuff without the
proper tools because there are people that steal these things believe it or not and so you kind of
want to make it theft proof as much as possible at least like basic theft. Anyways we have two
different kinds of chains here we have long link stainless steel chains and you have normal
stainless steel chains. Now you want to use stainless instead of zinc plated chains or
galvanized chains in order to not have it's like they're not going to lose too much strength with
rust right away but we want this to last a long time and we don't want to leave a bunch of rust
streaks coming down the rock right here. This already has a higher visual impact than just the
two bolts and so the long link chains allow for multiple things to be clipped into the same link
and these are less common so they cost more money. In this case I can get three carabiners in there
and then you want to make sure you're not loading this one you can't undo these ones if you're
in a situation where just plan ahead. But anyways this I've never found too much of a problem in my
opinion because you can just clip the next chain up so pick your poison either way the chains help
equalize the chains will help go over the edge and you can change them out if you have if you're
running your rope through the chains in order to top rope. Now there is a debate in the climbing
community on whether or not you should do this and wear out your own shit if you're going to top rope
in order to prevent accidents as much as possible even though people should be competent enough to
be able to clip in do some work and unclip you do want to minimize the amount of action that'll be
taken later. So something I like about pre-setting up the lower off at the end of the day is that
I don't have to like strategize who's going to go up last because sometimes you have a new person
that wants to try it. For example if I want to wear out my own gear I can put one carabiner here
maybe up that high and lock that and the wear and tear is going to be on my carabiner and it is
technically so redundant because you are in the chains and when they're done at the end of their
climb they can remove this and then you lower them off and there's no miscommunication on who's
doing what and untying and retying. Another way to protect your chains from getting worn out because
if they do they can uh when they create a groove they can create a sharp edge and you kind of
either have to cut off one link or change out the whole chain. If this is going to be used a lot and
people are going to lower off the fixed gear you can add a quick link to the system that may be a
bigger quick link that can take a lot more wear and tear and you can add a welded stainless steel
ring to the end of this if you wanted to as well because those actually they rotate and they
can spread out the wear and tear. But if I went through here and I don't have another quick link
with me but this well all the wear and tear is on this one chain but you get the picture um
another nice thing about chain is sometimes you cannot put your bolts perfectly in line because
your rock is has so much variation or it's shit rock and you don't get to just pick where you put
your bolts you can actually do different length chains in order to get them to be even. So I'm
going to go on a rant real quick if these things are off level just a little bit and the rocks
configured just the right way you can actually get your rope stuck when you pull it through.
I got stuck on El Capitan repelling from the stove legs because those wrap rings are off off centered
by one carabiner height and basically this happened to us and we pulled as hard as we could
and could not free our rope and basically had to jug our rope like this because we couldn't get help
and it was January we couldn't just bivvy it was awful. So make sure they're either even
or off level enough that it's not going to get that lock in place you also have to consider
your rock and where it's at. Okay I made it you didn't see that
you're so dorky. Anyways so when I get up here I'm going to show you
how I'm going to attach my rope through here there's two ways that I'm going to show you
one is you can just untie thread it through and re-tie in but that's caused accidents before
um it's still a valid way of doing it especially if you're on a
legitimate PAS which I do like my Petzl one here. I'm not that fond of uh
triple action lockers they're a pain in the ass. Anyways um the European way of doing this is to
with the small chain it's a lot easier with rings or quick links is I'm going to put um the tail
that goes down to my belayer on the bottom because once it's in this little chain I can't rotate it
and then I just tie a new knot before untying anything at all and if I'm at a good stance I
don't even have to use a personal anchor system and then uh here Bobby take and that once I know
he's got me then I can untie from here and we'll put in the links in the description below much
better videos about this from much more legitimate people on the subject but anyways all right you
got me gotcha cool it's always triple action lockers it's always nice to communicate and then
this eventually basically just comes all the way through and I'm lowered but this does add wear
and tear to this chain so it's uh just something to consider when you're putting in a climbing anchor
whether or not this is the configuration you want instead of being closed-minded
bolters we're going to go with more of an open system sorry that's a terrible joke so this is
an open system that obviously is going to be a lot easier so as I that's a handhold by the way
so when I come up here I can easily clip to these hooks and they're just so much easier
to um just install my my rope and then be lowered off and you can see there's just so much more
material here for wear and tear now these are mussy hooks from climb tech and they are not
just your typical toe hooks because these have climbing carabiner gates rather than the flat
shitty gates that the toe hooks come with because they are sharp and they snap off not too long
after they're installed now this is great if a sport climber is going to come up clip clip get
lowered off and the second person is going to follow and clean the route and you're just going
to use it for a few times but if you are going to gang bang a top rope you don't really want to use
gear you want to wear out your own shit okay so we'd go back to using our quad anchor for our own
stuff if we're going to possibly just use this all day with a large group of people there's always
two things to really consider when you're installing something that's going to be used a
lot like this is wear and tear versus corrosion now these are not stainless steel and we usually
advocate for stainless steel but this will hold up more than twice as much as a titanium bolt
however if you're near the ocean you would want to use a titanium open system which there are
available there's ram horns and all sorts of things in order for that to not corrode before
you wear it out so you got to wear weigh the two options but in most climbing war in most of the
climbing world you would just go with this steel hook and you would be able to replace it annually
or every so often when it gets worn down and gets that u-shaped groove in it another open system
that doesn't have any gates that could break or get in the way is a ram's horn or in this case
this might be called a pig's tail depending on what brand you get and what you do is you put the
chain on here oh man this is like one of those logic puzzles you got to anticipate the turn
so we'll go that way okay ha figured it out now that that's shut i can come up here
to the top of my climb and put my rope in and this isn't technically redundant as far as
the metal goes because there's only one but this would take two actions in order for it to
come out this is actually pretty nifty and it's actually something that can be changed out easily
enough for like what like seven bucks or something and so this is a one option if you're trying to
use a horizontal anchor but this is more commonly seen in an offset anchor which we're going to show
you now so let's start with a closed vertical system this has two quick links on here and
one quick link on here and they're offset in order to show you the benefits we're going to
show you however sometimes the rock demands that you also put these off level as well
but with this second quick link it the rope goes in correctly and the second this quick link the
lower one adds redundancy so this system is not going to get twisted it's less likely to twist
your rope than if you had another ring over here this can potentially cause twists this is not
going to cause those twists and if this were to wear out it's only wearing one point and if for
some reason it doesn't get changed like it should if it broke you're on a system that's pretty much
never seen any uh weight on it it's not worn out at all so no one would die if this thing wore out
however it is a closed system now we're going to show you some open system options with vertical
anchors so this open system you will see everywhere that bobby has been this is a system that he likes
doing and he puts the ram horn up here directly on the bolt and i am tied in still and so i'm going to
put my rope in there and of course you want it to rid redundant and so you have this additional
thing now if this is just the quick link that's not a open system so we have two options we have
this beefy ass thing which is not necessary because it's not going to see wear and tear so
you don't need the value that this brings which is the fact that it has so much metal right here
to take a beating so we muzzy not use those right now so here we have a captive eye stainless steel
carabiner this is a 316 stainless steel so it is more corrosion resistant than 304 and you'd put
that on the quick link and one thing we're playing with here is if you do this we've closed the quick
link obviously the question is if this were to pop off or break would this open the gate and cause it
to let's say cause it to open and come off um we're not quite sure that would happen the
alternative option we kind of are liking is to put it where the gate faces the rock now you never
really want to do that in any other situation but here it doesn't seem to be opening the thing it
there's no rock protrusion there and if it were to come off the top it's not
going to potentially open that gate at all it's basically just dealing with the back of the spine
of the carabiner leave in the comments below what you think of this anchor because uh this is pretty
neat to have this directly into a bolt with just a backup what would you do here and do you like
this is an option if you must see use this get it uh this can be placed up here because this can
take the wear and tear because it's got all the metal here and then you can back it up with
something else here uh so it is redundant now it is nice to have these vertical anchors in order
to prevent some twisting because if you have your two points sideways like this and your rope's
running this you know over it definitely has the potential of twisting your rope so this is actually
more common to be seen if you're going to have a ram's horn in a vertical scenario where the ram's
horn is on the bottom and it's made redundant or backed up by a chain going up here now this chain
you just slip over the top like you've seen in the videos here already and it's kind of a pain in the
ass to have not too much sag you never just seem to have the right length of chain plus it's not
truly redundant it's redundant in case this bolt fails but it's not redundant in case the ram's
horn fails which is why bobby prefers having this up here and then having something lower
that would catch if this were to either fail or the rope would come out which never happens but um
yeah it's uh
this is you'd never see this kind of stuff on like a multi-pitch climb or a big wall because
this is mostly for sport climbing and the visual impact of this uh being lower than the chain
is actually a lot higher because you have chain in the system whereas if the ram horn is up here
and you just have the one beaner down here you've eliminated chain you can still see the damn thing
but it does lower the impact this would suck to carry up stuff plus you'd have to carry like a
bunch of different lengths uh anyways leave in the comments below what you thought of this video
if we said something completely wrong or if you if we didn't cover an anchor that you've seen and
like we want to make sure the bolting bible has literally every option available everything about
it and we want to make sure the information is right so please leave in the comments below of
this video or in the comments below in the bolting bible on our website which is in the link below
we're completely redoing the bolting bible right now so it does include climbing and climbing
anchors and not just high lining because i like high lining instead of just smashing your knuckles
against the rock here make sure you smash that like button to help us grow this channel so we
can reach more people who might want to bolt so they do it right make sure you like follow and
subscribe on facebook youtube and instagram because we're posting stuff all the time cheers
