How to Knit a Pumpkin - The easy way that's so much quicker!

Handy Creators
62 followers
15 Video ViewsยทOct 29, 2022
If you have yarn laying around, and I'm sure you probably do,
don't spend a ton of money buying those adorable little pumpkins to decorate this fall.
Even if you aren't a pro knitter, they're incredibly easy to make.
We used the long tail cast on to begin, so we need a nice long tail for that,
but make sure to get a little extra so you have at least a 24 inch tail after you cast on 66 stitches.
So to start the long tail cast on, place the yarn over your needle,
gather the two ends and secure them in your fingers,
and stick your index finger and thumb between the two ends.
So each loop on the needle is one stitch,
and you'll want to repeat this until you have 66 loops or stitches on your needles.
My first choice for this one is Lion Brand Scarfie for one main reason.
The color transitions make for the prettiest pumpkins.
They also have a bunch of colors to choose from so you can match your decor,
and you can buy it at just about any craft store.
If you do decide to substitute and you want your pumpkin to be this exact size,
do try to substitute with a bulky or a number 5 yarn, and that way things will match up.
But just know that this is a really versatile pattern, so if you want a bigger pumpkin,
use a thicker yarn and a bigger needle.
Or if you want a smaller pumpkin, use a thinner yarn and smaller needles.
All right, when you have 66 stitches on your needles,
make sure the braid is along the middle here on the inside and that there aren't any twists.
Grab a stitch marker and place that on the needle so you know which
stitch is first and where the beginning of the round is,
and insert your needle in the first stitch and knit.
Then continue by knitting the next 9 stitches so you have a total of 10 knits.
And then purl the next stitch.
So that's the repeat. Knit 10, purl 1.
Now it really helps to know what you're looking at, especially if you're a new knitter,
because inevitably you'll get interrupted or distracted and lose your place.
When you see a stitch that looks like this,
with a horizontal line just below the needle or the cord, that's a purl stitch.
So you could just count back to it and pick up where you left off.
You always want to have 10 knit stitches followed by one purl stitch for the repeat.
So if you've done everything correctly, the last stitch should be a purl.
Then pass your stitch marker over and we'll continue to round 2.
The good thing is you already know the repeat for round 2 and throughout the rest of the pattern.
Knit 10, purl 1.
So continue with that repeat until your work measures about
6.5 inches from the cast on edge.
You'll lose a little bit of height with closing the ends,
and the finished pumpkin will sit about 2.5 inches tall when you're done.
But the pattern is pretty versatile, so if you want a taller pumpkin,
just keep knitting until your work measures about 4 inches
longer than you want the pumpkin to be tall.
When you're ready, we'll work a simple bind off.
Go ahead and remove the stitch marker, you don't really need that anymore.
Then knit the first 2 stitches to start the bind off process.
Then with your needle, grab that first stitch and pass it over.
And that'll bind off one stitch.
So knit the next stitch, and pass it over.
And repeat this for all of your knit stitches.
When you get to the purl stitch, go ahead and purl that one instead of knit it,
and then of course pass it over as usual.
So as you're binding off, make sure you're knitting the knits
and purling the purls so we can keep the pattern consistent.
When you have only one loop remaining on your needle,
just go ahead and pull up on that remaining loop and cut yourself a nice long tail.
We'll use this for the shaping in just a little bit.
Now grab your yarn needle and thread it on one of the tails.
We're going to create a drawstring to close up the two ends.
So run the needle through the stitch,
then skip a couple stitches, and run it through in the opposite direction.
Skip a couple more stitches, run it through again,
and repeat all the way around.
You need one full circle so we can draw up the end.
One thing to note here, if you're using scarfie or any roving yarn for that matter,
keep an eye on the yarn.
If it untwists, it'll lose its strength and fall apart, which you don't want to happen.
So just make sure it stays twisted throughout the entire process.
Carefully pull on the tail to draw it up as much as you can.
It's not going to fully close here.
We'll fix that later.
Just draw it up as much as possible.
Then with the needle, you'll run that around the opening to close it up even more.
Now I find it looks a little neater when I focus on the areas that are already sort of popping up,
and when I push the ends down into the hole.
Run it through several times to make sure the opening is nice and secure.
So now we want to do the same thing on the other side,
but this time have your stuffing ready.
Create the drawstring as you did before,
but before you close it up, add the stuffing.
Honestly, this part will make or break your pumpkin.
If you don't stuff it enough, it won't have a great shape,
so err on the side of slightly over stuffing and just make sure it's evenly distributed.
Then continue to secure the opening on this side as you did on the opposite side.
When you have the shape you want,
poke the needle through the center and out the opposite side.
Now it'll be a little awkward with extremely long tails here,
but tie the two ends together and pull it tight enough to slightly cave it in.
From here, you can use either of the two ends to complete the shaping.
Most of this pumpkin is the solid yellowy mustard color,
so I'm going to use that end so it'll blend a little bit better.
To get started with the segmenting of the pumpkin,
align the tail in one of the pearl grooves and loop it around to the opposite side
and poke the needle through the center and out the other side.
Then pull on it a little bit to cave it in.
Now you'll have to hold on to that with your two fingers here on the opposite side,
then rotate it a little bit and do the same for the next pearl groove.
Make sure you're steadying that on the opposite side and repeat.
You'll do this for all six pearl grooves to create six pumpkin segments.
When you're done, cut the two ends to a more manageable length and tie them off.
You can either weave these in or you can tie them.
I'm just going to tie them because nobody's going to see the bottom of this pumpkin
and I don't have to weave them in, but you can do whatever you prefer.
Now I'm using a cinnamon stick for the stem, which smells great and it looks pretty cool too.
You can find a stick in the backyard and that'll work just fine,
but I really do prefer the look and smell of a cinnamon stick.
Now you'll probably need to break it to make it much shorter.
Just be careful when you do so. These are extremely hard to break.
And then use some hot glue to secure it in place.
That's all for now, friend.
Thank you so much for watching, subscribing, liking, and commenting.
Those little actions, although they don't seem like much,
really do help make a big impact so I can continue sharing this craft we both love.
Happy knitting and I'll see you in the next one.
