Curved Concrete Countertop / Bar Top

Ceramik
19 followers
6 Video Views·Oct 27, 2022
What's happening everybody? Today we're talking about curved concrete countertops.
How about a curved bar top? Let's make something cool!
Adding curves to your concrete can add a dramatic yet elegant look. So we're going to just jump
right into making this mold. So we're going to start by talking about the material we're going
to use. So the key to this project is going to be using a material called whiteboard.
It's similar to malamine when it's got a nice plastic finish on it, but instead of being a
particle board substrate, it's a hardboard substrate,
making it nice and flexible to get those smooth subtle curves for our mold.
Let's cut the base to a more manageable size, then rip two strips at an inch and a half thick.
We need to make a cardboard template, and I'm going to show you how to do that simply by using
a nail and a string. I'm going to show you guys an old trick. First, you're going to tie a little
loop on the end of your string. You're going to take one of these really cool clamps. I'm going
to clamp it down at the end of the table right at the edge, and you're going to draw your line
along the bench. Now we can hang our tape measure right in the end, and then we're going to make
our two marks for our inner and our outer radius. In this case, our radius is three foot six inches
nine sixteenths. Our outer radius is two foot five inches and eleven sixteenths. Insert a 16
penny nail through the loop, drive the nail into the ground, and this will be our pivot point for
the string. Then position a marker at the marks you made and draw the arc. Also, don't go leaving
nails in your driveway. Simply cut the template out with a razor. Now that we have our cardboard
template cut out and our base cut, all we have to do is trace our template. Now that we have our
template traced, I like to start by attaching the straight ends first. That will give our flexible
pieces something to attach themselves onto. I like to use a pilot drill with a countersink and drill
one inch deep. Then screw an inch and a quarter spack screw into the base, clamp the other side
down, and repeat. Now we're going to make several anchor blocks made from your scrap. Place the
blocks just behind the curved lines about a foot apart and attach them however you want. I know
you're watching me do a lot of tedious steps, but I promise the juice is worth the squeeze.
Rip one and a half inch strips of the flexible hardboard and attach them at both ends using
brad nails or screws, but do not use brads or screws on the anchor points. We're going to use
Rapid Set Flexible Construction Adhesive to secure and seal the hardboard to our anchor points.
Instead of using mechanical fasteners, this will avoid any nasty holes on the inside of our mold.
Turn the mold around and repeat. I promise this is all totally going to make sense in the end.
That's pretty much it. We have our sides secured. We have our flexible sides sealed and secured.
It's pretty much ready to go at this point, but I want to take it just one step further.
We're going to get all Pinterest-y up in here. We're going to make our concrete countertop just
a little bit more visually appealing. We're just going to give it a little more
just by simply adding a little trim. So let's go to our local home center
and let's go check out their molding aisle.
Check out this aisle. There are a hundred different profiles to choose from. Check it out.
We're going to use polystyrene cove molding for our project.
Butt the cove to one side of the mold and temporarily clamp it to the edge using spring clamps
and mark the cut. Run a bead of Rapid Set Flexible Construction Adhesive and clamp in place.
Spring clamps will save your life and they only cost a dollar a piece. For the side,
we just want to tack it in place because we're going to remove it after the first pour.
I cut a cove joint at the end of this piece. I'll explain how to cut cove joints in a later video.
It is cold outside. It's about 19 degrees outside. I made sure that two of these bags stayed inside
overnight to warm up a little bit. Got myself some warm water. Spray the mold down with WD-40
and wipe off the excess. If I plan on using a design, I will either print or draw my design
on a sheet of paper, laminate it for durability, and cut it out with a razor. Now just sprinkle
dry sanded grout over the design. The WD-40 will help the design stay in place. For detailed
instructions on how to mix Rapid Set Mortar Mix, just click on the link above or watch my
How to Make a Concrete Countertop in One Hour video. Don't forget the flow control. This is
going to make your life so much easier. Pour the mortar mix in a spot that won't disturb your design
and be ginger about it. The nice wet mix will flow right over the grout. If your mix is too thick,
it'll push your design all over the place. And don't forget to tap those bubbles out.
Depending on temperatures, you should be able to take your concrete countertop out of the mold
in one hour. Oh yeah! Now we got to get this cleaned up and ready for pour number two.
Since we're going to make a mirror image of the first slab, remove the left cove molding,
then cut and attach a new cove base for the right side.
For the sink knockout, we're going to cut two pieces of 3 1⁄4 inch melamine
at 12 inches by 9 3⁄8 of an inch and sandwich them together. I used a drafting compass to mark
my 1 1⁄2 inch radius on all four corners. I used a drum sander to sand the corners down,
but this would have been much easier with a belt sander. Let's make these rough edges nice and
with some packing tape. Normally, when I use rapid set cement, I don't bother using any kind
of metal reinforcement or rebar. But with that being said, you want to use your best judgment.
For instance, in this project, we've got a very skinny piece here and a very skinny piece up here.
So we're going to put a piece right here and we're going to put a piece right here.
I bought myself a four foot piece, cut it in half, making two two foot sections.
Tap the rebar down about three quarters of an inch, but not all the way down to the bottom
surface. Our next step is to mount this sink. In order to give us a more streamlined look,
we're going to undermount it instead of mount it on the top the way it was meant to be.
But we can't use the hardware that it came with. Instead, we're going to get anchors meant for
concrete, one inch fender washers, and a masonry drill bit. This technique is going to save us
several hundred dollars. An undermount sink would cost anywhere from two to three hundred dollars
and it'd probably be special order and it won't come with a faucet. A hundred dollars and it comes
with a faucet. Don't be intimidated. This is going to be very easy and I'm going to show you. Mark
the depth at one inch with blue painter's tape and don't drill past the tape. I ran a bead of
clear silicone on top of the sink before setting it into place. Now just insert your screw through
the washer and secure the sink in place on all four corners. I cut a 15 degree bevel on all the
pallets and just screwed them together. Rapid Set Flexible Construction Adhesive is like hot sauce
to me. I put that on everything. Seal the joint with Rapid Set Non-Sag Sealant and guys, thank
you so much for watching my video. I hope you got something out of it. If you did, hit that like
button and if you haven't subscribed already, think of subscribing. I promise you won't regret it.
I only open my KBS's up on special occasions and uh
what better special occasion than 30,000 subscribers in only two months with one video.
Thank you guys so much. Cheers and I'll see you in the next one. It is way too freaking
cold to be drinking cold beer. Who am I kidding? It's never too cold to drink cold beer, right?
