Here are 5 clever electrical tips, tricks and hacks that everyone should know! See if there are any here that are new to you! #homehacks#electrical#tipsandtricks
🎬 CHECK OUT THESE RELATED VIDEOS! 🎬 • 7 CLEVER Picture Hanging Tricks Everyone Should Know: 7 CLEVER Painters Tape Tricks Everyone Should Know: Two FREE and Cheap Ways to Fix Gaps In Your Floor: PRODUCTS IN THIS VIDEO 📦 • 75 Pc UL Listed Wago 221 Lever Nuts: https://geni.us/J7R1D • 81 Pc Lever Nut Kit: https://geni.us/el6r • 141 pc Lever Wire Nut Connector Kit: https://geni.us/52Bd • Heat Shrink Tubing Kit: https://geni.us/YqN9azW • Replacement 3 Prong Plug: https://geni.us/PBbJd • Replacement 2 Prong Plug: https://geni.us/dcF2bmu • Heavy Duty 3 Prong Plug Replacement: https://geni.us/ZYXsQ • 250 PCS Heat Shrink Wire Connectors: https://geni.us/ZNeQBs • Vise-Grip Universal Wire Stripper: https://geni.us/MMoEuJ • Generic Universal Wire Strippers that seem nicer than the Vise-Grips: https://geni.us/dbXL8 Links above are affiliate links, which means you pay the same price as always but we make a small commission, which helps out our channel - so thanks!
👍 WANT TO HELP SUPPORT THIS CHANNEL? 👍 Become a channel member! Hit the "Join" button or head to us on Patreon: https://www.patreon.com/lrn2diy
📲 MORE DIY GOODNESS 📲 Check out our many projects and plans at https://lrn2diy.com
📲 WANT TO LEARN MORE ABOUT 3D PRINTING? 📲 All things 3D Printing at The 3D Printing Zone TWO FREE AUDIOBOOKS! 📚 To get two free audiobooks from Audible, just follow this link: https://goo.gl/QGFC4Q
00:00#5: Ditch the Twist Connectors 01:43#4: A Strong Fix for Cut Wire 02:57#3: Don't Toss That Broken Cord 05:03#2: Always Work With the Grain 07:24#1: The New Wire Strippers Are HereCredit: LRN2DIY
Here are five clever electrical tips,
including why I think you won't mind giving up these. Tip number five,
there is a way better alternative out there to using these.
Tip number five is to stop using morets.
So these things basically have a little metal housing on the inside,
and these are used to try to connect your wires.
And the fact is you just don't know if it's actually making a positive
connection or not.
So the replacement that is so much easier to use and so much better is these
guys. These are called lever nuts.
So you can take a couple of wires like this and let's grab one of these that
does too. And if you look up close here inside, there's a couple of inserts.
And when you close one of these,
you can see that that metal inside there where it's pinching down and making a
positive connection. So as I feed my two wires in here,
just feed them both in like that, push down the lever.
And then with that, I've got a nice positive connection.
I can visibly see that the levers are engaged. So there's no issues there.
Another great thing about these is even if you've got a situation where you've
got several wires here, I've got five different ones.
And I've even got one that's a much heavier gauge than these 14 gauge wires
here. I can still feed all of them in, make sure they're all pushed in,
lock down the levers, and then I can use these five.
And if I need to change something out,
let's say I need to replace the source for this one.
I can pull that one out and then put a different one in later, slide that in,
lock it down. It's in there snug, and I'm good to go.
Now these kits are pretty inexpensive. They're usually around 20 bucks.
And the nice thing is they have all different kinds of connectors.
There's lots of pieces in here.
And you have that peace of mind of knowing that everything is connected exactly
the way it should be. And there's no guesswork involved. Tip number four,
when you need to splice wires together, twisting them is not the answer.
If you're trying to fix a wire that's been cut like this one,
start by stripping the wires about an inch and a half or four centimeters deep.
Exposing the wires inside.
Twist each set of wires until it resembles one solid wire.
Slide some heat shrink tubing over one side.
And we'll come back to this toward the end of this step.
Starting with one of the wires,
create a hook where the rest of the wire follows parallel to the existing wire
and then bend over the end at 90 degrees like this.
Now repeat that on the other wire, line it up like you see here.
And then once you've got the open ends going through the loops of the opposite
piece, then grab those open ends and pull tight.
You can see it creates a perfect little knot here. And as you pull apart,
it's just going to tighten that knot, making a stronger and stronger bond.
If you need to,
you can snip off any excess wires that are hanging out over the insulated area,
slide over the heat shrink tubing, and then melt it a little bit with a lighter.
The two wires have now become one again.
They're sealed and protected with a good contact signal.
And they're not going anywhere. This is a super strong bond.
You can give those a good pull and they're not going to come loose no matter
what. Tip number three,
there's no need to replace an entire cord if just the plug or end has gone bad.
We've all seen this before where your cord seems to break in exactly the wrong
spot, right up near the plug. Fortunately,
there's a pretty easy solution to this. To start,
you'll need to cut the cord where you can get a nice clean end. Looking inside,
we can see that we've got three wires here.
We need to expose the three inner wires. So to do this,
we'll use a sharp blade and make a small cut or incision at the end of the
cord.
We can then peel it open and then pull those wires back to get as much as we
need. In this case, a couple of inches will do just fine.
Cut off the excess and then strip about a half inch of wire on each one.
We can now get rid of the old plug.
And we're going to replace that with a standard three prong replacement plug,
just like the old one. This one has a ground, a hot and a neutral.
You can just pull the top right off and then feed the wires in through the back.
The colors of the wires inside the cord that you're fixing may vary in color.
Sometimes they might actually be black, white, and green,
just like you'd find in an outlet. But more often than not,
they're using other colors. In this case, the brown,
the blue and the green are pretty traditional and the brown represents the hot
or the line. The blue represents the neutral and the green is ground.
The colors of the screws inside the replacement plug are typically going to be
brass, silver, and green. Green is always ground.
Brass is always hot and silver is always neutral.
Loosen each of the three screws and then feed the wires in and tighten them for a
good secure connection. If you need to feel free to trim any excess wire.
So there's no extra wire hanging out with the wire securely in place.
You can put the top of the plug back in and then use the three course threaded
screws to fasten it in place.
The last step is to tighten the clamp on the back.
There are two screws to fasten there. And once you've got those tightened down,
that plug is nice and secure, not going anywhere. And as good as new.
Now these replacement plugs come in both the three prong and the two prong or
non grounded variety.
And they usually cost just about two to $5 at the hardware store.
I'll put some links in the description below in case you want to pick one of
those up online.
Tip number two is to always work with the grain when you're working with screw
terminals. You've probably heard the term righty tighty lefty loosey.
What some people get confused by is the fact that that refers to the top of the
rotation. So on a screw like this, for example, on this light switch,
when you turn the screw clockwise, the top of the screw turns to the right.
And that's where the righty tighty lefty loosey comes into play.
When you're using a hook like this,
ideally you always want the open end of that hook to be towards the right.
If you line your hook up backwards,
like I've got here where the opening is on the left,
then what can happen is as you tighten,
it's going to try to open up that hook and it could slide it right out from
underneath the head of the screw. The more you tighten,
the more likely it is to push it right out. I'm tightening this one down,
for example, until it's nice and snug.
And when it feels like it's all the way tight and everything's got a good
connection,
you can see that it's actually popped right out the sides and I can just pull it
away. If on the other hand,
I choose to go with the grain by putting the opening on the right side.
Then as I tighten that down,
both the screw and the plate underneath it are going to tend to close that hook
and that's going to create better contact and a better electrical bond between
the wire and the terminal. For this demonstration,
I used a pretty loose hook just to show you what could happen.
But if you use a tighter hook, you're going to have better results,
no matter what. In fact,
you can see there's a little ledge or a little drop off so that it tends to
hold that hook or that wire captive inside there.
So these are really designed to work as best as possible, even if you do it wrong,
but by doing it right,
you're going to get better contact and a better signal every time.
This same tip applies even more so to stranded wires like this one.
If you place the wire in the wrong orientation or against the grain,
as you tighten the screw,
it will tend to push all of those little strands out and away from the screw
itself, making an even poorer connection. When you place it with the grain,
it's going to tend to pull those wires along with the tightening of the screw
and make a much better connection. Better yet,
tighten up those threads as much as you can by twisting them into one solid
piece, wrap it around with the grain, tighten it,
and you'll get a much better connection overall.
If you do have to connect a stranded wire like this to a screw terminal,
one of the best ways is to use a U-type or a fork connector with the stranded
wire, and then just insert that under the screw. And as promised,
tip number one is why I don't think you'll mind giving up these.
Wire clippers have been around for a very long time.
One of the trickiest things about them, however,
is knowing what size wire you're trying to strip.
Oftentimes you just don't know,
and that requires a bit of guesswork to try to try one and then the other and
see what works and what doesn't. Just a few years back,
I got my first set of these new style universal wire strippers,
and these are pretty awesome for a host of reasons.
The way these work is very simple.
Basically it's got some jaws and it's going to grab both the right side and the
left side, and it will pull the right side away from the left side.
It will either remove that sheathing altogether,
or at least separate it enough that it's easy to pull off yourself.
The crazy thing is this works on any size wire.
I can do this on 20 gauge or 18 gauge. Like I've got here,
I can do it on 14 gauge wire and still not having touched a thing.
I can do this on even 10 gauge or even eight gauge wire.
It doesn't care and it doesn't matter what size wire I'm putting in there.
Now those were all solid wire,
but you can see that this actually works just fine with stranded wire as well.
The best part is it doesn't actually cut into the wires themselves.
A lot of times when you're using a sharp blade and you're trying to cut it
precisely, you end up cutting some of the wires and that weakens the signal and
gives you less area to make contact with.
So whether it's a thicker stranded wire, like we just did,
or even a really thin and delicate one like this, it can handle it.
No problem. And if you look close up here,
you can see that all of the wires are intact. Nothing is missing.
Universal wire strippers typically tend to come with all of the features that you
see on traditional wire strippers,
like crimpers in the handle and a wire cutter.
Now there's one other huge feature that these universal wire strippers have that
traditional wire strippers can't touch.
And that is they can tear the sheathing really easily off of complex wires.
Let's take a look. For example, at this ethernet wire, typically to open this up,
you're going to have to make a little slit somewhere and then pull that sheathing
back. But with these universal wire strippers,
place them in there anywhere you want, and it will just break that right off.
Piece of cake. This also works super well on multi-wire cables like Romex.
Here's some 14-2 cable, for example, that it handles no problem.
It even works on 14-3, which is wider than the jaws themselves.
But as you can see, I can grab onto it, pull it apart,
and then I can either yank the rest of that off or just flip it around and cut
that as well. Remember earlier,
when we were trying to replace that plug on that power cord,
well those little three cables that are in there are pretty delicate and we
don't want to cut into those.
So rather than snipping the end and then pulling the sheathing back,
you can just use some universal wire strippers and it will pull that outside
sheathing off without a problem. Then without touching a thing,
you can also strip the three small wires inside. As you can see here,
this is rated for 10 to 24 gauge wire,
but I've found that you can go lower than that and higher than that.
And this thing can handle just about anything without any problem.
If you are working with finer wires,
there is this little knob here that you can twist to adjust the delicacy or the
pressure with which it actually pulls those apart.
These wire strippers also have a depth stop built in. So if, for example,
you want to take off a half inch off of a whole bunch of wires,
you can just set your depth stop to a half inch, push each wire up against it,
squeeze the trigger, and you'll get consistent results on every wire. Now, hold on.
We're not done just yet. There's actually seven more things I want to show you.
Hopefully you found some cool stuff in there, but what about painter's tape?
I've got seven clever tips for painter's tape that you can check out right here.
And I'm pretty sure you're going to learn something new in there, by the way,
none of them involve painting as it turns out. So go ahead and click on that.
Tap on that. Do your thing.