Weekend Bathroom Remodel Part 2 Laying Vinyl Tiles

Handy Creators
62 followers
5 Video Views·Oct 14, 2022
This is the second in a short series of videos showing how to remodel a bathroom. This video shows how to tile a bathroom floor using vinyl tiles and how to grout in between them. The previous video shows how to remove everything from the bathroom (excluding the tub), to get ready for new flooring. Subsequent videos show how to install beadboard and a new faucet.Credit: LRN2DIY
For this next phase, we're going to need several pieces.
This is basically the stuff that we're using
is this Traffic Master Ceramica stuff here
and it's vinyl. It's got an adhesive back but it feels and looks like tile. It
doesn't have the same hardness because it's not
actual ceramic like real tile is but
we applied this in our basement bathroom already
and we're pretty happy with the results. One of the things that makes it really
nice is because
is that you grout it in between so it really does look like tile. It's not the
stuff that's just
butted up against one another that looks like linoleum essentially.
The other advantage to this is it does have kind of a warm feel to it
as opposed to tile which can get pretty cold unless you have heated flooring.
This box cost about $35.
Our bathroom is pretty small as you can see so this is more than enough to do the
whole bathroom.
That's one of the things we've got here and then
we're also going to need our spacers. I went ahead and got the quarter inch
because I like to be able to see the grout really well
in between. We need a float
of some sort to be able to spread the grout and then
we're going to need a utility knife with a fresh blade in it so that we can
cut the tile. So with these you don't need a tile cutter or anything.
It's soft enough that you can actually score it, cut it, and separate it with
a utility knife. I've got our pre-mixed grout here.
Just a tub enough to do what we need. Our sealer for when we're done.
And then just for helping out I brought a couple of
straight edges essentially that we can use. This is what I use to do my
drywall and then just a
T-square or a square I guess, speed square they call it.
We'll use that to help score and
cut the ceramic tiles or the vinyl tiles.
So I'm going to go ahead and start in this corner over here by the door.
So that's the first thing that you see when you walk in is that the tiles are
nice and straight and even
and they're full tiles. I'm choosing to do
my portion of a tile back here. So let's go ahead and get started.
Alright so a couple things to keep in mind when you're getting started here.
If you look on the back of the tiles they all have arrows pointing in a similar
direction
or in one direction so you want to make sure that you make your whole entire
floor
pattern in the same direction. So for example I've got that one now pointing
this way.
I don't want to have this one pointing that way because there is a
usually some sort of a grain or a pattern to these so we want to make sure
that
we look at which direction they're facing each time.
My first tile that I've got here, I've got a piece of trim back here behind the
door that I've got to work with.
So I went ahead and already used the chisel to
take a piece off but I need a bigger piece out so I'm going to use my
utility blade and take a little bit more off here
and really how this works is you can just kind of score these
and there we go and then once you've given them
got them scored you can kinda
they're pretty rigid so you can
break these things off. I'm going to score this one deeper.
There we go. So I've got a line there
and I can just break it off like that. Now I might need to take off more but I'm just
taking a little bit off at a time until I get to exactly where I want to be.
So yeah I definitely need to go a little bit more. Another piece
off there. That's looking closer.
So as we're moving along there are going to be some parts that are a little bit more
tricky to cut around. So for example around this
door frame I had to try to really
edge it in so that it fits that contour nicely
because as you can see it really has to just go snug right up against it there.
And I still want to have my quarter inch spacers here
have everything line up as it should. So
on that I was able to just use the blade
to cut in and nick it off a little at a time. You can see
there's a lot of scraps here where I had to just kinda do a little bit at a time
and try to figure it out. But now that that's in there
double check that my arrows are pointing the right way.
Peel this thing off. Get it all prepped.
And then basically lift these fibers up
and I can really just slide it right in.
And then now that it's there
put my spacer in. Make sure I'm in the right spot.
Same thing down here. Okay that one's good.
And then I'll just make sure it's level
with the next tile. And once it's in
it stays in really nicely already. Just want to push that down everywhere. Make sure
that's really firm on there.
And we're good to go. So the next one
just so you can see the process here. Tilt over a little bit.
So I'm going to grab my next tile. Check my
arrows on it. I see some loose
sheetrock here. Must have missed with the vacuum.
Get all those out. Make sure I've got a good clean area to work with.
Get my spacers ready. And before I
actually peel anything I just want to test fit it.
Make sure there's no obstructions or anything in the way. That looks good.
Alright so I'm going to put my spacer in there.
And then I've already got my corner guy right here.
Bring this over.
And I'm good. So as you can see they go pretty
easily. I just want to keep double checking my spaces.
Make sure I'm in the right spots and that everything's
lined up really nicely so I have nice straight lines from
one row to the next. Okay we're back for day two.
I went ahead and finished up the tile overnight. Got all the pieces in place in
our
second bathroom here. And we've got them all spaced. I went ahead and cleaned
everything up.
Vacuumed. Took the spacers out. So now we're ready to go ahead and get on with
the grouting.
So for grout we just need, in this case I've got a small bathroom so I didn't
buy the bag of grout or anything. I just need a little bit
that I'm going to be using here. And then we've also got a float or something
with kind of a spongy surface on it to basically spread the grout in.
A sponge itself to do some cleanup. Some paper towels.
And then I'm just going to use a putty knife to help scoop some of the grout out.
And then a bowl of water just so I can rinse some of the stuff off the sponge
and help keep things clean as I move along. So I'm going to use the float to do
most of the work.
The putty knife that I have here
is really just to scoop some stuff onto the float.
Okay so in order to apply the grout we basically just want to
cover as little area as we have to.
Use the float to spread it on.
And then working at a diagonal is usually a good idea. Like this.
Just pulling it. Making sure you get it nice and full.
So that there's no empty spots, cracks, or gaps
in between the tiles. And then you can just use your
where did I put that? Yeah you can use the grout container
to get the excess off. And then
basically just get all the stuff up off the floor.
And then once you've got that up that's where we get out
the sponge. Get this wet. Ring it out a bit.
And then it's pretty easy to clean up like this.
Again kind of going at a diagonal. And you'll see it leaves a nice
smooth line of grout.
Then I like to use the paper towels to just do a
wipe up. This is all pretty
wet on the tile. The part that's on the tile. I'm trying not to get this
in the actual grout too much. Just kind of glossing over it.
Then we're left with nice grout lines. So I'm going to continue that process
throughout the
rest of the floor. And we'll check back in in a minute.
Alright now that we've finished the grout the floor is looking pretty nice.
I chose an alabaster grout that goes pretty good with this kind of
tan or salmon colored tile. And finished right up to the edges.
And when we start putting everything back together we're going to need to
do a lot of caulking along the edges to make sure these little areas like right
in there for example we're going to make sure they're really sealed.
So that if any water does spill this place is like sealed tight like a swimming pool.
So that's the next step. But that is the
flooring and tiling portion of the bathroom.
