Why you’ve been CHANGING TIRES WRONG | How to Fix a Flat

Children Of The Loam
44 followers
23 Video Views·Jul 14, 2021
We show you how to fix a flat the right way! Don't make it harder than it should be! - Most people make a few mistakes when changing a tire that makes the whole process more difficult. We show you all the techniques to get the job done quick and easy. Fixing a flat shouldn't be super complicated and this video should simplify the process for you. Thanks for watching!
Follow our Instagram! https://www.instagram.com/childrenoftheloam/
All right, guys, what's going on?
Jackson here for Children of the Loam.
Today, we're gonna be showing you
how to change a tire the right way,
because I see so many people do it wrong.
My friends, people I work with at a bike shop.
So we're gonna settle this once and for all
and make this easy for you guys
so you're not struggling and breaking levers.
Ugh!
Ha ha!
All right, so these you should not need
other than taking the tire off.
When we put it on, I'll show you guys
is the best way to do it
so you're not even gonna need levers.
Save you a lot of time and frustration.
Soapy water, isopropyl, something like that,
just to help the beads see a little bit easier
and kind of slide over the rim.
And then a bike pump,
unless you got some type of special lungs on you
that I've never seen before.
All right, guys, so to start off,
assuming there's a little bit of air still left in your tube,
you're gonna have to let that out.
So we'll go ahead and do that.
Pretty straightforward.
And kind of lean on it.
The more air you get out, the better.
That actually helps to close the valve
because sometimes it reinflates a bit.
And we'll start opposite of the valve.
Break the bead loose.
This one's actually kind of already coming off.
We didn't see it all the way before.
Sometimes they're tricky.
The best way, if it's tough,
get your thumbs in there like that
and just push towards the center.
Let's see.
Kind of like that.
All right, so now you got that off the bead
on both sides, all the way around.
And grab a lever.
Start around the valve.
Typically, try not to pinch the tube if it isn't flat,
which I don't know why you'd be doing this if it wasn't,
but it's just good to know.
Break that free.
This one's a little sticky.
And run it around.
There we go.
This tire's a bit stubborn.
Once you got it broken,
you can just use your fingers and go around.
Come up here.
Take that off, which I forgot to do earlier.
Where it went, I don't know.
Yank your tube out.
Set that aside.
And pull the tire off.
Simple as E.
All right, so if your tube went flat,
it's worth checking what caused it to go flat
so you don't put a new tube in
and instantly puncture it again,
which happens more often than not.
So what you can do is just pump up your tube.
This one isn't flat,
so it's not even worth showing you guys,
but just inflate it to the point where it starts leaking.
You'll be able to hear it.
Find where the hole is.
Compare it to the rim and tire,
just based on where the valve is.
And then look in the tire
in the relative area that it had a flat.
And you'll probably find a thorn or something like that.
Sometimes it's a pinch flat
so you won't get anything like that,
but you'll be able to see if there's something in the tire
and obviously take that out before you put a new tube in.
So now that we got our new tube,
put a little air in it,
just about as much as this one has in it already,
just to give it some form.
Makes it a lot easier.
Now to reinstall,
make sure you got your tire in the right direction.
Can't tell you how many times I've done this wrong.
Lenny's bike is-
What's the right direction, Jackson?
To get the tire on the right way,
most of them will be marked.
You can see that arrow right there.
Rotor's on the left.
And since we're doing this the right way,
you gotta line up your logos.
Get that center X right there, right over the valve.
That way, you don't need to be looking for your valve.
You just look at the logo and you know it's there.
If your logo's over the valve,
your decals on your tire is gonna line up
with the rim decal.
It looks faster.
If it looks faster, it is faster.
All right, so now we've got one side of the tire
seated all the way around.
All right, one side's in.
Then you take it.
And it helps to sit down
when you're changing tires, I've found.
It's really the easiest way to do it.
You're not struggling and fumbling all over the place.
So, take your tube on the valve hole.
Go ahead and insert that in there.
And just go around, tuck your tube in.
Make sure it's not twisted or rolled up or anything.
You can see that.
Nice and uniform the whole way around.
So now, you can take, this isn't necessary,
but it helps.
Whatever you got, a little soapy water or something,
just run it around the bead.
All right, so then take your thumbs
and kind of pull up over the rim
and pull the tube back.
Keep it from pinching.
Get that bead in there.
Just kind of work it around,
up towards the valve.
Start to get tight there, so then you come back here.
Where you started.
Pinch and push this tire down
into the center of the rim channel.
Keep tension on it and just run your fingers around
and you'll see it starts to loosen off.
And you just keep doing that until it goes.
No tire lever's needed.
All right, what made that look so easy?
Because that takes me 20 minutes.
What made that look so easy?
It's just taking that tension,
or creating tension on the tire
to just pull it in to that center rim channel
and you're essentially pulling the slack
up to where you need it.
Yeah, because the tire's a tight fit around the rim.
Definitely.
You need every single little bit.
Yep, anything helps and if it doesn't work
the first time like you saw,
you just keep working it and it will eventually go.
So now we're good there, like I started to say.
Just go around, check that your tube
is not protruding out from underneath the tire
because if it's like that and you go to inflate it,
you'll flat immediately again
and nobody wants that to happen.
So now that we're good all the way around,
just go ahead, connect your air device.
Glory work.
And give her a pump.
Barspin.
Yep.
All right, so when you're doing this,
you can come in close here and you see how this line here
is not consistent all the way around,
how the tire tucks in there?
You really want to make sure
that it's even all the way around
because that indicates that your bead is seated.
The line needs to be equidistant
from the rim all the way around.
You'll see it snap into place as you pump up more.
Woo.
Wow.
Damn.
All right.
That was more than expected.
So now you can see we got that line even all the way around.
Now your tire's not going to be wobbling when it's rolling.
It'll feel a lot smoother, go a lot faster and stay on
and hopefully not flat again.
But you usually have to go higher
than the recommended pressure to get that to snap in,
or not most of the time, but some of the time.
So just make sure you don't go too high
and blow the tire off the rim.
It's worth noting.
And yeah, now we'll just let some air out
back to where we want it.
Pretty solid.
Take your little nut, thread it back on the valve
and get your cap wherever it is.
Mine's imaginary.
It's on there now.
You're done.
All right, guys, that's going to do it for this one.
Hopefully that helped you.
Hopefully you won't be breaking levers and cursing,
changing tires, going forward.
If this video helped out, we'd appreciate it a lot
if you'd like, comment, and probably subscribe too.
Oh, that one fires me up.
If you have any questions,
the comment section is down there.
Keep it real, guys.
