🌳 MATERIALS ~25 BF of 5/4 White Oak Rubio Monocoat in Cotton White https://amzn.to/2NA9Tni 3 x 3" x 3" x 8' Square Tube Steel 1 x 3" x 8' x 1/8" Flat Steel Hex Bolt Screws + Washers Acetone/Mineral Spirits Metal de-greaser
📲 Check me out on SOCIAL MEDIA! INSTAGRAM: instagram.com/workshopedits FACEBOOK: facebook.com/workshopedits
Chapters: 0:00 - Introduction 0:15 - Milling Lumber 1:23 - Drilling Dowels / Joinery 3:40 - Glue Up 4:48 - Sanding / Cutting Top to Length 6:17 - Applying Finish (Rubio Monocoat) 8:59 - Cutting the Steel Base Material 9:27 - Welding + Grinding 11:05 - Finishing the Steel Base 12:49 - Final Assembly 13:06 - Final Shots + Outro
Thanks for watching! Zach
What's up guys, I'm Zach from Workshop Edits.
In today's project, I want to take you through how I built this gigantic white oak and steel
kitchen table.
Let's go ahead and get started.
Alright, so we are here in the shop.
We have all of the material that we need to build the tabletop.
Really excited about this one, so let's go ahead and get started.
Alright, so boards are cut to their rough final length.
I used the joiner to make sure that one side was completely square, and then I ripped the
other edge square over at the table saw.
These boards are not all the same length, but that's not a big deal because they're
going to be glued up as one giant panel.
The other thing I did was, these boards, they should come all the exact same thickness from
the hardwood dealer that I got them from, but just in the off chance that they're not,
I also picked the side that was eventually going to be the top and planed that down.
That way they're all the exact same thickness, and then I also know which side I'm going
to eventually use as the tabletop.
So we're going to organize the boards, and then we're going to get to drilling dowels.
Now I'm going to be using this $20 jig from Rockler to do that.
It works perfectly well.
It takes a little bit more time than something like a domino, but it's really good at creating
a strong joint, and it keeps things lined up perfectly, which I want to do as best as
possible to just make sure these boards are lined up when I glue them together, and that
I don't have to eventually plane them down and lose some of the thickness.
So we're going to go ahead and do that.
All right, so I have all the boards ordered how I want them.
I've also marked them just to keep track of everything.
You can see, actually, they're not all perfectly flat, but once things are glued up, it should
be relatively straight.
I also have them lined up laterally just to try to get rid of some of these knots, and
I actually have enough material, which is great, so that once I cut this thing to final
length, there's not going to be any imperfections on top.
So the way that the dowel jig works is you're going to have to drill a dowel on each side
of the board.
So what I'm going to do is just go along here, and I think I'm probably only going to use
five per joint, and I'm just going to use my speed square, which is 90 degrees, line
up the two boards that I want, pick exactly where I want my dowel to go, and then I'm
just going to draw a line that goes between the two of them, because then the way that
this works is there's a little line on this jig.
I'll line it up on each side, clamp it down, drill that hole, and then those boards should
slide together perfectly.
All right, so all of the holes are now cut for the dowel, so the next thing we're going
to do is head over to the table saw, and we're just going to cut this half-inch dowel that
I got from Lowe's into a bunch of tiny little pieces, then we can get on to assembly.
So let's do that.
All right, so dowels are cut.
I also sanded down the edges of them.
It makes it a little bit easier to hammer those in and not be such a tight fit.
So now we're going to glue these up.
So what I've found with doing these big panel glue-ups is that it's easier to glue just
one or two panels together at a time.
Because I have five of them, what I'm going to do is just glue two sets of two, and then
I'll probably come back in an hour or so once that glue has set up properly, scrape
away any of the excess, and then glue the third panel to another one, and then come
back an hour later and glue all five of them together.
It's just going to help keep things flat and allow me to control the final output of this
thing and then eventually just avoid having to do a lot of extra cleanup on the end because
I don't have a giant planer that I could run this through or even a drum sander to do it.
All right, so the tabletop has been sanded up to 220 grit.
I started off with 60 and then went up to 120 on the orbital sander, and then used 220
with some hand sanding just to smooth these things out perfectly.
I also sanded up to 60 grit on the bottom side.
The next thing that I want to do is cut this to its final length.
So what we did off-camera was bring the tabletop inside to where it's going to be and figure
out exactly how long we want it to be, and we landed on 6 feet, 72 inches.
So I've marked out exactly how I want to cut this.
I have it flipped over on its bottom side because I'm going to use my circular saw to
cut it, and by having it flipped over on the other side, the way that the circular saw
blade rotates is going to prevent tearout on the top side.
I'm also just going to do a test cut to see if I have to lay down some blue tape.
Just want this to cut as clean as possible, but really excited to see this in its final
size, so we're going to go ahead and do that.
All right, so the tabletop is now sanded up to 220 grit.
I also used a spray bottle, some water to wet the top surface of the table, raised the
fibers in the wood, and then sanded those down again.
That way, because this is a kitchen tabletop, when it gets wet in the future, it's not going
to become rough over time, so that's good to go.
The other thing I did was just use a chamfer bit and add a very small bevel to the top
and bottom edges of the table.
Gives it a little bit of a nicer aesthetic, and it's also just going to be easier on the
wrist.
So the next thing we're going to do is apply finish to this thing, and so for this project,
I'm using Rubio Monocoat in Cotton White.
There are a ton of videos out there on how to apply this finish properly.
I'm not going to go into a ton of detail on it.
If you do want to learn more about it, I'll leave a link to a video from The Wood Whisperer,
Marks Bagnola, in the description.
He has a great video on applying this finish.
For this project specifically, we're going to be using the two-part mix, which has the
accelerator in it, because if you don't use that, it takes about 21 days for it to cure,
and I just don't have that kind of time.
So what we're going to do first is just clean everything off with acetone, mineral spirits,
get rid of all that dust.
Then we're going to apply the finish, buff it in, and then wipe away all the excess of
it.
I'm just going to work here, let you watch.
If you want to learn more about it, again, check out the link in that video description.
All right, so I just finished applying the Rubio Monocoat to the top of the table, and
what you probably noticed was how much whiter it was on the top versus the bottom, and what
I didn't realize, just having never used the finish before, so a little tip, is always
mix the Rubio Monocoat finish before you use it.
I think my product had just sat on the shelf for so long that the different components
of it had started to separate, which meant that the cotton white color wasn't properly
mixed with the other oils, so having done that before, doing it on this top coat, it
came out much better.
It is beautiful.
We are going to let that cure now for a week, and move our attention to the base.
The base is made entirely out of three-inch square steel.
The legs themselves have a seven-and-a-half degree angle to them, so what we're going
to do is break all of those components down using the metal chop saw.
We're going to set the chop saw at seven-and-a-half degrees just using my protractor, cut all
those pieces so that they all have the exact same seven-and-a-half degree angle, then we
can move on to welding everything up.
All right, so all of the steel pieces have been cut.
That includes four legs, two small cross-horizontal supports, one long horizontal support that's
going to connect both of the leg bases, and then the flat three-inch stock that's going
to actually attach to the top of the legs and fasten the legs to the table, and then
I also cut smaller three-by-three-inch pieces that are going to go at the bottom of each
of the legs so that there's a nice flat space to put something underneath those to eventually
protect the floor.
The next thing that we're going to do is take all the pieces that we just cut, use the angle
grinder and a flat disc to clean them up and prepare them for welding, and then we're going
to be ready to start assembling this table.
All right, so the tabletop is completely welded up, and it has been cleaned off with a degreaser,
so that is good to go.
I went back, I marked out, and I drilled out pilot holes that's going to later accept the
screws, which will screw up under into the tabletop.
So what I want to do is bring in the table.
The table's been carrying for about five days, so the oil's about 90% good to go, should
be plenty fine to work with.
What I want to do is sit it on top of the table, measure and mark out exactly where
the flat-plated steel is going to touch the table, and then I'm going to actually route
out an eighth-inch-deep groove that's going to accept that metal.
That way, the base will sit flush with the underside of the tabletop, so we're going
to go ahead and do that.
All right, everything has been routed out.
I also pre-drilled holes, and I used just a piece of tape to mark the depth that I wanted
to drill through, just so I didn't drill through the tabletop.
The last thing I want to do is, because the base of this table is steel and we want to
keep it as a raw steel look, is I'm going to go over the entire piece with my orbital
sander using 80-grit and then 120-grit, and what that's going to do is just give the steel
a nice kind of uniform look and kind of blend together all of the welding places and the
places that I cleaned it off using the angle grinder, and overall, it's just going to give
it a nice, complete look.
So we're going to do that.
Then we're going to follow up, clean the entire thing off with acetone, and then just give
it a clear coat with the rattle can.
That way, the raw steel is protected and it's not going to rust over time, and once that
clear coat dries, we're going to be ready for final assembly.
All right, so that is going to wrap it up for this video.
I am thrilled with how this thing came out.
I just think it came out.
It's so beautiful.
The white oak with that stain is just awesome.
The steel base is just super clean.
Overall, so excited to have it in our kitchen.
If you did enjoy the video, just let me know by hitting that like button.
I would love it if you would subscribe to the channel for any future videos, and I'm
looking forward to seeing you on the next video for whatever it is that I'm building.
Bye.