What is a camshaft? Let’s cover the basics!

Charley’s Garage
78 followers
Camshafts are a vital part of engine operation. They help determine how well and engine breathes and timing. In this video we cover basic parts of the camshaft and details about why those parts are important.
Check out where I got this camshaft here:
https://www.mac.bid?r=AA9FE08B
Use this code/link for $5 towards your first auction win!
As always if you decide to purchase from a product link this creator earns a commission and is extremely grateful for you!
#mechanic #diy #automobile #dieselrepair
In today's video, we are going to be talking about the camshaft.
So, what is a camshaft?
A camshaft is responsible for really two things
that are really honestly just one thing said
two different ways, right?
So, the purpose of the camshaft is to open
the valves that let air flow in and out of
your head and into your cylinders, right?
And out of the cylinders.
And it does that with the use of these guys,
which are called cam lobes.
and you can see that the cam lobe if you look
on one side it's pretty flat but then if it rotates
you see that it is on a high side all right
so these things are rotating usually driven by a
chain a belt or a gear by the crankshaft
and they are timed to the crankshaft so that when that
piston is coming up this guy is timed to open
the valves at exactly the right time all right
the spots that we have that are between these are where caps would go
and mount this to the
cylinder head because this one is an overhead cam
not an in-block cam so those are the two
locations that you might find camshafts they could
be sitting on top of the cylinder head
pushing directly down on like lash adjusters
and little rockers or directly on a roller on a rocker
to push that valve open now what causes
the valve to close is when the high point of the
lobe right here is pushing down as it rolls off
of it the spring pulls the valve back up
all right so the middle spots that we have in here
the smaller spots off the cam lobes are what we
would call the cam journals cam journals are going
to be held on by caps or they're going to be
journals are going to be bigger than
the lobes actually for an in-block cam and slide into
bushings and stuff so different ways of mounting them
but these journals are important because
they really tell us two things one i need
to be able to measure the journals and measure the
place that it goes in to find out how much oil clearance i'm going
to get inside that area
your camshaft oil clearance can be a reason
for low oil pressure if that clearance gets too
excessive so proper oiling proper clearance
is really important we would take a mic and measure
this which I'm going to do in a different video show you guys how
to do the measurements but we
would measure this the other thing we could do is put
this in like a v-block and rotate it and put
a dial indicator right here
and then as we rotate this cam it's going to tell us that this cam has
any bendage or warpage to it so this is one of those times
when I'm using a dial indicator on
something I want to see that dial stay still as long
as it doesn't move around as I'm rotating it
It means that I got a nice straight camshaft, all right?
The other thing I'm worried about
is that this is a wear surface on this cam lobe.
So your cam lobe itself is what determines the lift,
and that's kind of how much movement you get to open those valves.
There's other things involved with that,
like rocker ratio, which we'll talk about later,
but this is a significant portion of how far your valve stays open
and how far you're uh uh how long
or duration right the other thing that i told you guys i
said there was two things is really one thing
if the camshaft is determining when the valve opens
that means the camshaft is determining the timing of the engine
or even the i guess i should say the
firing order right so for example if you have
a v8 uh you could have two different camshafts that
could completely change the firing order of the engine
and the best example i know of from personal
experience with that is the difference between
the small block fords like your 289s and your 302s
and then the 351 you can put a 351 type camshaft
into one of those small block fords and it will
completely change the firing order
but the engine will still run right and we'll kind of explain
that more when we start talking about position piston positioning
and timing which is going to
be in a future video. So one of the ways
that I can check to see if my camshaft is still capable
of doing the job of opening, because as this part wears,
you're going to lose that lift.
So what we would want to do is you've got
this short area of the cam right here. We would call
this like the inner base circle,
or sometimes it's just referred to as the base circle. I would put
a micrometer here, and then I would take that micrometer
and measure the nose, you know, the
lift, the lobe part. And then if I subtract those two measurements,
the base circle and the lift,
the lobe, I'm going to find out how much lift I get.
So for example, a 3.04 Duratec, I know it
has a lift of 0.189 inches.
So if I was measuring that on that engine and I got 0.185, 0.184,
I could tell there would be some excessive wear on this lobe.
It's time to replace that camshaft.
all right another way you can do this again
is in the v blocks you can put a dial indicator on this
guy and zero it on the flat spot on the base circle
and then slowly rotate your cam to the
high spot and just watch your dial indicator
and that will tell you lift also so you can mic these
you can use a dial indicator multiple ways of doing that measurement
so these cam shafts like
i'll show you a quick video of one that i took
that's out of a ISX Cummins uh there's no way i
would be able to demo an ISX Cummins by sitting here
and holding it and showing you the parts of
it because it weighs i don't even know how much it weighs
but let's just say that i hurt my back
when i pick them up uh so that's why i went to uh amazon
and got this uh cheap little guy at auction
so i could show you guys this stuff uh one
of the things i do want to point out though is this
channel is growing very fast
and the money I make off this channel helps me do things like buy these
little training aids to show you guys how stuff works
and explain things and one of the ways that
I can make money off this channel is memberships
so if you become a member I don't believe in
making videos that are just for members only I have
a few of my older videos that I've made
members only but I do this for everybody
so my members aren't going to get exclusive videos
what you are going to do is know
that you're supporting me educating people about engines
and trucks and things like
that and as this channel grows i'm planning on putting out a
reward system for memberships
so drawings for tools uh t-shirts uh stuff like that uh so if
you become a member you get involved
and the longer you're a member the more uh entries you're
going to get into those drawings once i start
making enough money off this channel but for now
it's all about just showing you guys this stuff right
so uh this is pretty cool uh if you're
interested in being able to find i got this camshaft
for like five bucks off the MacBids auction
and i'm going to put my MacBids link in the comments
and in the uh description so that you
guys can uh check it out because you can find some pretty good deals
on MacBids and they sell
pretty much everything uh obviously i got a camshaft
and i got a crankshaft that i'm getting
ready to do a video that i paid like five bucks for also
so uh really cool place MacBids check
them out so if you have any questions about camshafts
that i didn't cover in this video
you can see the oiling holes right there i forgot
to point those out that's how oil gets in there
to lubricate so this would be the spot where
your cam is mounted to your let me find it here
this this right here would be where your cam is mounted
so this is where the oil would come into
those clearances so these are the areas you want
to pay specific attention to when you're measuring
these are your journals all right
and then the front of the cam you can see it has a keyway right
here and these keyways are so that when you put like your gear on here
or something like that
that gear is going to make sure that you have timing marks
that you can properly align when
you put your timing chains on or in some cases
a timing belt in the diesel world i deal mostly with
timing gears so you could have a gear on the crank
and then a chain or a belt that comes up to the
cam to rotate it or you could have the the gear on the crank
and then another gear between the crank
and the cam gear and so the timing
though putting the crank in the right position putting the cam
in the right position before you put the chain belt
or gear on all very critical to ensuring
that you have proper engine timing all right
so again this is the camshaft opens the valves
intake and exhaust sometimes you will have one camshaft
on an engine that will have lobes for
both intake and exhaust on them sometimes you'll have two
per cylinder head where one's opening
just the intake valves
and the other one is opening the exhaust valves that Cummins ISX one
that i was talking about that one has two camshafts
on the old version one that was just for the
injectors and the other one had three cam lobes
per cylinder one for the brake one for the intake
and one for the exhaust. The newer Cummins ISXs did away
with one of those camshafts because they
went with high pressure common rail,
which means they didn't need a rocker arm for the injectors
anymore. So now it's a single overhead cam.
So a lot of varieties out there. So again, if you have
any questions about the camshafts,
I'm trying to make this video under 10 minutes so that I keep
everyone's attention span, because I know if you're like me
and you're scrolling pretty quick.
so again questions please put them
in the comments please like share send this to people
you know that might be interested in learning about engines
and as always be careful out there
catch you on the next video
