In this episode, we install a massive 130,000L Kingspan Heritage water tank beside our new shed, plus a slimline urban tank beside the garage, as part of our bigger plan to future-proof the water supply at our Johanna cabin. We go through the planning, rainfall calculations, tank sizing, site prep, crusher dust pad, downpipes, colour matching, installation day and the final setup, including how we’ll eventually connect it all back to the house.
Thanks to Kingspan Water Tanks for partnering with us on this project! If you are looking for a new water tank check them out below.
Do you have a product you want us to review? 👉 SEND TO: Attn: Jonno Rodd Hunting for George Parcel Collect 10103 33142 350 Orrong Road Caulfield North 3161 Victoria, Australia
Here's something that I had no idea about when we moved away from the city.
The fact that our livelihood and general well-being would rely on one thing on our property.
You want to see it?
Our water tank.
And it's cooked.
When I was a city slicker, I had no idea how much water I consumed because I kind of didn't need to.
But since living here, we've run out of water twice.
Twice!
Because our gutters and our water tank suck.
So that's been our biggest problem living here that no one really knows about.
We've been doing a ton of research and geeking out over water consumption
and analysing the best possible water tank solutions to future-proof our home.
And today is the day all of that time and energy finally pays off.
But we mustn't dwell.
No, not today.
We can't.
Not on water tank installation day.
Not bad.
Did you know that the average person uses around 150 litres of water a day?
We estimate our family will use about 450 litres in a day.
That's about the volume of two wheelie bins.
In a month, we'll need 13,500 litres.
That's about the size of 90 bathtubs or 40% of a 20-foot shipping container.
So that's how much water we need per month at a minimum.
But how much water can we actually collect?
The roof and the gutters on the house are cooked.
That is definitely a project on the cards, but not something we're going to tackle right now.
We don't have the budget or time.
Right now, I have to work out exactly how much water we can collect off the new shed roof
and that small garage roof.
So to do that, I'm going to use the Kingspan Rainwater Calculator.
Very simple little calculation you can do on your own, but these guys make it even easier.
You just plug in your roof area, which for the shed is 200 square metres,
and then your annual rainfall for your area,
which you can find on the BOM website or somewhere online.
I know that ours is average 950 millimetres a year,
which gets us 190,000 litres collected every year off the shed.
For the smaller garage, 36 square metres and 950, the annual rainfall stays the same.
So we'll be able to collect 34,200 litres off that roof as well.
So based on how much water we can collect from the available roof space that we have,
I've chosen 130,000 litre Kingspan Heritage Tank to go next to the shed.
And an 8,500 litre Slimline Tank to go next to the garage.
Collecting water off the house is a project we'll tackle on another day.
I do want to work with a three tank system.
We will install another tank when we get to the replacing of the roof and new gutters on the house.
You do want to calculate in some sort of headway and room in case you don't get rain,
like we didn't get two summers ago.
You want to have at least three months worth of capacity in your tank to use at any time.
Those calculations are average rainfall on high rainfall years.
We'll be able to fill that tank three times, maybe more.
Okay, so that's the functional side of things.
Now let's talk about form.
The water tank is actually going to take up quite a lot of surface area,
much like our shed.
And one of the reasons why we chose Kingspan
is because you can choose from the Colourbond steel colours.
And I spent a lot of time specifying the exact perfect colour for our shed.
So I wasn't just going to put any old water tank on our property.
No, I specified woodland grey.
So this is going to match the shed
and it's also going to work really well with our environment.
And it's all Australian made certified bluescope steel.
We have a concrete pad next to our garage,
which Jono did when we had our garage floor poured.
And this is going to be where we put our slimline water tank.
The main thing with this space is I don't just want it to be for the water tank.
I also want it to be a space to house all of our bins.
My plan is to design the water tank to be as large as possible,
but also leave quite a lot of room for the bins to fit
and then eventually have Jono build a really nice structure to conceal the bins.
He just doesn't know about that one yet.
So I've got to work out how big I can make this water tank
whilst also fitting in those bins.
And I'm just actually using a resource that Kingspan have.
It's their 3D water tank builder specifically for their urban tanks.
So we're going with the slimline urban tank,
but you can also choose from lots of different shapes.
And then you get to specify your dimensions.
You get to choose your color.
So you can spec it up to fit your exact needs.
I really like the look of these slimline urban tanks.
These are very common, obviously, in the city, hence the name.
Usually tucked beside, you know, the house in between the fence.
But for us, it's going to be much more on display.
So what I actually want to do is plant out a bit of a garden in front of it.
I want to put in lots of beautiful Australian natives.
So it's actually going to be a bit more of a feature
and it will be a backdrop to hopefully a luscious garden.
New water tanks are on the way.
So time to do a bit of prep and sort out the problem
everyone's been pointing out in the YouTube comments.
And that's that I didn't paint the downpipes.
And there's a good reason for that,
because they're not connected to anything yet.
Today, we're going to sort out our downpipe issue
and make sure we've got enough space for one,
because the tank that we're getting is very big.
Then on Monday, we've got our crusher dust coming.
We need to get a good solid 150 mil compacted pad down
before the installers turn up and start putting this thing together.
So let's get cracking.
Well, before we built the shed, we did do a big site cut.
And from memory, that far corner to this corner was a 900 mil difference.
So there was a fair bit of cut out there.
And then all of the material that was cut out was pushed out the front
because you don't want to build on the topsoil.
You want to get down to the solid clay like we are here.
And then the same thing here, the site was sloping a bit.
So we cut into here and we've ended up with a bit of a drop
down from the height of the shed, which is not a problem.
I cut back into here to put this wall in,
and it was rock solid, the base of that thing.
And now I put crushed rock back in behind it,
and I'll give it a whack over with the compactor later.
But I didn't want to cut any further towards here for two reasons.
A lot of material to take out.
Then I just have to sort out another drainage issue.
And I had also put my big aggie pipe all the way through here,
and it just sort of nicks off the end of that retaining wall.
And then I've got a plan for this 900 mil by sort of four, five meter section,
a bit of an outdoor cleaning station with a tap and a little sink and stuff.
So I'll fill this in when I'm all done,
but I'm going to work out the center point of the tank first.
Make sure I've got enough space that way.
I have to scrape off a little bit more there.
And then when the rock comes on Monday,
I'll get them to dump it straight here, spread it out, compact it.
It'll be good to go.
So I've got it almost exact.
I wanted to have that set back 900 or a meter.
And I've just measured, that's a meter exactly.
I want it to have 900 usable space.
That's good.
Will be the center.
That's the center of the tank.
We actually finally got some rain the other day,
which is good because we didn't get rain through January, February, most of March.
That's the biggest reason why we're doing all this
because last summer we ran out of water twice,
which wasn't that fun.
Because if you run out of water, you have to pay for it.
I'm gonna have to re-screw that on, aren't I?
Get some longer screws.
So this is quite a big job.
Quite a big and expensive job.
I only want to do it once.
And I don't want to have to think about water again.
I want to have more than I need.
Set this bad boy up somewhere.
I won't run over it with the tractor.
Is it level enough?
Come on, buddy.
Start spinning.
Spot right here in the center.
Quite low.
So if that's the height we want,
I think I went on a little bit of a low spot.
Low already.
Good.
Low.
So this bit's really wet here,
only because this downpipe's just discharging everything from here down when it rains.
But there will be a little bit of a fall,
and I'll cut a bit out there so the water can run off.
But the only bit, this is all good
because I did all this the other day before I did the retaining wall here.
It's pretty good.
Barely have to do anything.
It's just this little corner here.
I'll just have to scrape out this tiny bit here,
and then I'll fill the tiny spots.
Needs to be within 10 mil once the crusher dust is down,
but that's easy to fix.
But yeah, let's just scrape that tiny bit,
and we might draw a circle.
See how big it's going to be.
Close enough.
Doesn't look level, does it?
It's level enough.
I'll get it level when I put the stone down.
All right, here's the center.
I marked it before.
That's the center of the tank,
so it's offset.
So if you hold it on the thing,
it's 8.6, so it's 4.3 half.
I might be a bit close here.
Mixed up.
It's all right, we can shift it a bit.
It's approximate.
It's all right, we'll shift it.
My pad is going to be bigger anyway.
It's going to be oversized.
I'm bringing the pad out an extra meter.
Big tank.
It is a big tank.
Not really looking forward to this,
and I want to work out a solution
where I don't have to do it all the time.
But I'm going to have to clean out the gutters,
and I've got to pull these downpipes down.
And I got sent this thing.
Lock Jaw Ladder Grip.
Perfect time to work out how to use it.
She just clamps over the gutter,
and then that bit goes over your ladder.
Oh, that's actually very good.
How's that?
Straight on.
Just clips in.
It actually stops it wobbling a bit.
All right, I've only put one screw in this,
which is not even...
Oh no, I put two screws in it.
While I'm up here, I might as well get these gutters cleaned.
This is going to be an absolute nightmare.
There's so much in here.
Just put a couple of temporary screws in it.
It'll be easy to get out.
Oh, there they go.
Just need a little helper.
I've got threads the whole way.
I don't know why that was spinning.
Anyway, they're out.
On to the next one.
Look at that.
You know what would make it even better?
If you could put it on and take it off from down here.
It does actually stop the ladder from wobbling while you're up there.
I'm just going to get the down pipes off first.
All right, there it goes.
Look at that.
Full of leaves.
One down.
And yes, I'm going to recycle all these.
I'm going to design it.
I'm going to work out my length, my joins and everything.
I'm going to make little sections.
I'll paint them before I put them up there,
because there's no way I'm painting them up there
and then trying not to paint the shed.
All right, let's go.
Oh, that gutter bracket's popped out.
Can we get it back in?
Probably not.
Oh, that gutter bracket's popped out as well.
Oh, and that one.
More problems.
Why do you have to make it so difficult?
Look at all this.
Disaster.
Problem with getting crap in your gutters is it actually holds water.
This is whole sticks.
Look at the size of that stick.
All right, number two.
Come on, get off.
Oh, the other one came off easier than this.
There it goes.
Off.
And twisty, twisty.
There she blows.
And down.
Just got to wait for a truck now.
Well, that's about 14 cubes of crusher dust.
Probably need to start spreading it now.
Could take a bit.
The other day when I was scraping back everything,
I left this little marker with a datum point for my height,
which is going to help me for the next couple of days.
So I don't have to keep finding a reference point.
That is my reference point.
That is the cut level.
And then that is my 150 mil thick base.
I might draw it on the retaining wall.
So when I throw it in here, I've got somewhere to know where it's got to go to.
I've got to be able to see that first board.
I'm not going to be able to see that because the pile of dirt's too tall.
Just below that second retaining wall block.
That's going to roll away.
I'm just going to cut all my bits and pieces on the drop saw because it's quicker and easier.
Time to paint some downpipes.
So we're going to hit it with a bit of plastic primer.
Little Dulux number.
At lawn, we didn't actually do this.
We just painted it with the weather shield and it's holding up fine.
But I thought, I've got it.
And it's easier to paint this stuff now before I get up there five meters in the air
and then try and tackle painting it up there.
So I will paint all these bits and pieces.
I've taped off the ends that need to be glued.
And then when I get it up there,
I can get up there with a touch-up brush and just touch it up.
I do have to paint the very top of the pop through the downpipe
because that's not the right color.
We're in my little makeshift paint booth.
This is literally going to be my office soon.
But for the moment, use it as a paint booth.
All right.
Get some primer on.
How long does this stuff take to go off?
Clean.
I have actually sanded it with a little Scotch Brite pad.
800 grit something.
30 minutes.
Touch dry in 20 minutes.
30 minutes.
So we'll hit it with this plastic primer.
And then I've got a little mini spray gun and I'll just water it down just a tiny bit.
And hopefully it doesn't make too much of a mess.
This stuff's really hard to see because it's clear on white.
One dry and we'll get the main paint mixed up.
We might have had a little false start with the spray gun
because this spray gun pumps out a lot of air when you turn it on.
And it blew all my pipes over.
But we've shimmied up a little system which I hope will hold them.
Let's go again.
Let's see if we can't knock all these out
because the weather is actually really nice and they'll probably dry.
All right.
Let's go.
All right.
Paint's dry.
Time to get these down pipes fitted up.
They look good.
Funny thing about this woodland grey.
When you paint it, it looks really green when it goes on wet.
But then it dries and it's like a perfect match.
A few spidey webs.
A bit of water in here still.
Which is annoying.
But let's let it drain out.
And it blocked off.
Oh try not to scratch the new paint.
All right.
Go to the other side.
Spiders everywhere.
Sun's out now.
You're doing something to me.
And I wanna be the one.
I wanna wanna be the one for you.
Standing there.
Music like a flower.
Your hair.
I won't let your power in.
All night.
Baby you move me like a movie.
You groove me like a groove.
You're doing something to me.
And I wanna be the one.
I wanna wanna be the one for you.
Standing there.
Music like a flower.
In your hair.
I won't let your power in.
All night.
All night long.
Baby you move me like a movie.
You groove me like a groove.
You're doing something to me.
And I wanna be the one.
I wanna wanna be the one for you.
Standing there.
Music like a flower.
In your hair.
I won't let your power in.
All night.
Say kiss me and she'll be in.
All night long.
Baby you move me like a movie.
You groove me like a groove.
You're doing something to me.
And I wanna be the one.
I wanna wanna be the one for you.
How good is that tank looking?
I'm so stoked with how it looks.
So stoked that we went colour matched.
Colour matched downpipes.
Colour matched roof.
Works in good with the rock colour.
Really just want it to blend in.
So I've left my brackets on the walls.
I still have to make and paint this last section of the charge pipe.
So I'm just gonna press fit it for the time being.
I'm gonna have to grab another ladder.
It's a bit of a jigsaw puzzle of multiple ladders.
Get the glue.
Don't get the glue on you.
I'm gonna need that.
I wanna make sure that I've got everything I need to start.
So I've painted everything.
I've colour coded everything.
Even these brackets look so much better.
Colour coded screws.
It works.
It's actually quite warm today.
Even though it looks terrible.
It's dead northerly.
Have to ditch the jumper.
And I did something smart that I don't normally do.
Actually labelled which one's which.
Because they might have been slightly, slightly different sizes.
Is that all the way?
All right.
Got a bit of paint touch up to be done.
And I don't know how I'm gonna pop them off and glue them.
But anyway, let that glue go for a bit.
All right.
I need somewhere to put this.
Bloody cobwebs everywhere already.
Can't see what I'm doing.
Oh, how do I hold it?
Oh, s**t.
Um, yeah.
You're gonna have to.
Can you just get up that orange ladder?
Sorry.
Yes, quick.
Sorry.
Otherwise I'm gonna have to drop it.
I'm gonna break it all.
Quick.
Can you just hold it up?
I can't hold it up.
Oh, no.
Good save.
Well, it's a little bit complicated by yourself with just a ladder and no scissor lift.
And it's more of a three-man job.
Leo, did you help?
At least he didn't scream.
I don't want this one to leak.
That's the important one.
That one at the corner.
It's not really, it's not going to fill up with water.
Water's just going to pass through it.
So in the end, I just got to touch up the paint.
We'll have to do it on all of them.
So I might glue these ones now.
Actually, what have I done?
That's the only one I can't get a ladder to.
And it's the only one, it's the last one I'm going to glue.
That's literally the only connection I can't get a ladder to.
I'll have to put a ladder on top of the tank.
I've got to glue these two at the same time.
So I just need you to hold these ones away from the wall
so I can get glue around them and hold these up.
Just a little bit of touch-up paint and then we're done.
It's all finished.
Yay!
What do you reckon?
I think you did the best job ever, Jono.
Not to be dramatic, but this is like probably one of the best things you've ever done.
Well, I only did the prep work.
I only did the prep work?
Yeah, the Kingspan guys rocked up before the sun even came up
and smashed it out by about 11, 11.15, which was excellent.
But made very hard filming in the dark.
But I reckon it still looks good.
It looks amazing.
End result looks epic.
Colour matched to the shed.
Colour matched downpipes.
Yeah.
No more YouTube comments about not painting the downpipes.
They're painted and I reckon they look good.
What do you reckon?
I think they look good.
Can I just say, after having done all of this,
I can only see downpipes now every time I go for a drive.
I just notice people's downpipes on sheds.
Yeah, but even on houses, people just don't finish it and don't paint them.
But I notice it now more than anything ever before.
And can I just say, no one's looked like that.
That is seamless, Jono Rodge.
Yeah, they're quite neat.
Absolutely seamless.
For someone who's not a plumber.
Yeah, I know.
Like what, YouTube?
Yeah, no, not even.
It's just gluing, I don't know, just gluing plastic together.
It's like the simplest job in the world.
But if you take your time and ever think about where they're going to go,
make it neat and then paint them.
Yeah.
And don't damage them when you put them up.
And don't drop them when you're trying to put them up.
Yeah.
Like what happened.
We had a few, a few snaps.
Luckily, I was able to help on that one.
One of the most satisfying parts of this water tank is actually this rain gauge.
So we can track how much water we have in the tank.
Pretty fun watching it go up very slowly,
because obviously when we first had it installed,
it was sitting on the ground.
Yeah.
Because the tank does go about 200 mil into the ground
because we had to get a bit of crushed rock pushed up against it
after it was installed.
So it doesn't blow away.
So rabbits and things don't crawl under it.
And there's little marks because we obviously had long periods
where there was no rain.
But yeah, it started down there.
It spun around on itself for about two weeks
and then it jumped to there,
which is probably what, 10%?
Then it jumped.
And then we were sitting there only a week ago.
Yeah.
And then in 24 hours, we got 100 mil of rain.
Knocked it all the way up to that and it went really quick.
So now it's half full.
Still got plenty of space, don't we?
Lucy thought my circle was too small or too close to the walls
when I was doing the setup,
but I think it worked out perfectly.
You can still walk down there.
No one's going to get stuck or trapped.
It's not dangerous.
Far enough off the shed, but it's close enough.
It's around this side.
Pretty simple.
We've got our main outlet.
That'll hook straight into our pump station,
into the pump, through the water filter, back to the house.
Then we did put in a CFA fitting.
Bush fires, if the fire is ever turned up
and they're looking for water,
they can hook up there, drain the whole thing.
We don't care as long as they're doing their job.
So I kind of hid all the utility side of the tank
down the bottom end where you don't really see it every day.
Obviously fittings, access ladder.
There is a hatch there.
You can get in there if you need.
Not for me, but if they ever need to repair the lining or anything.
And then the mega, mega overflow,
which I didn't think we were going to see in effect this year,
but the tank's already half full.
So I reckon it's probably going to overflow at some stage.
I'm going to have to keep an eye on the runoff
and make sure that I get some grass in here.
But I think this is like a 200 mil overflow,
because if you can imagine, this is an 8.6 meter tank.
That's a lot of water that can eventually start
flowing out all at one time.
But it does have a big sort of bell mouth fitting in there.
So that goes in, goes up,
and then it sort of pools over like a pond
and then starts overflowing once it's full.
So we'll see later in winter if it actually overflows.
So obviously after the Kingspan crew left,
there was a little bit more work to be finished.
We had to dump a heap of crushed rock around the base of it.
So rabbits, animals, things don't crawl under
and chew through that liner.
I also had to backfill all the gravel here.
And I've done a bit more work on the driveway,
a little bit more work to do,
but at least it's level, it's compacted.
It drains pretty well when it rains.
I also built a little pump tank station.
I don't know what to call it.
Where the water pump's going to go,
the water filter system's going to go.
And then as soon as I get a line hooked up into there
and then the line back out, we'll run it back to the house
and we can sort of decommission that old concrete tank
and that'll be a great day.
Yes, it will.
But I really like this.
It's really neat.
And again, it's just very seamless,
all with the woodland grey.
You had some offcuts from the shed.
Yeah, a little mini roof.
All matchy-matchy.
And what's that?
Is that the leftover concrete sheet?
Yeah, that's the James Hardy fine texture.
Cladding sheets that I've used on a number of things.
That's what the garage is built out of.
One request.
I like it.
It's easy.
Can you put a padlock on this?
Because I'm always already trying to open it.
So that'll be good.
Don't want small children climbing in there
and messing with everything.
And the retaining wall looks really good.
I think once this greys off, it'll look really nice.
Like this.
This one's greyed off already.
I've got to get my little outdoor tap in,
get a hose reel in.
Got another little plan for some stuff going in here.
Work in progress as always.
But the tank's done.
It holds water.
It holds a lot of water.
And I think we've solved all of our water storage problems
because we've got the other little tank
that we need to look at as well.
Yeah.
That's overflowing.
Grab a look at that.
This is our slimline urban tank.
This was the very easy part of install.
They literally, what, dropped it off.
It took a couple of minutes, don't it?
Yeah, I gave them a hand sliding it into place.
But I think it looks really good.
And this is also, might I add, my emotional support garden.
Basically because I planted this when I was having an extremely bad day.
And I took out my frustrations on the plant so they know all my secrets.
But the idea here is that I've got lots of Australian natives.
I've got grasses, some low-lying shrubs, a few kind of taller ones as well.
I think they'll get to about a metre.
Like some of them might get to two metres max.
But I think it's probably going to be more like a metre, a metre and a half.
So this is then going to be a really nice backdrop to this beautiful garden once it all grows up.
So this is for watering the garden, you know, making sure we can water,
you know, any veggies and herbs, that sort of thing.
It's also already full, I'm pretty sure.
It is full.
I might hook up a temporary little transfer and start dumping it into the big one.
Oh, very clever.
Just so we've got the option to do it in case we ever run out of water again as well.
And can I show you probably the most satisfying thing when you look at this tank?
Can you show the old tank side by side?
Compared to this one, that's going to be a very, very good day
when we can say goodbye to that old water tank.
Because the plan here, once that goes, then we can really have fun with landscaping.
So this is just the start of a garden.
We'll put in some retaining walls.
We'll be able to create pathways, a lot more lush plants.
I know that's going to come much, much later, but that's the part that really excites me.
So cleaning up and getting rid of the old junky looking stuff.
Yes, yes, absolutely.
We just put a normal ball valve outlet on the bottom
so I can run a poly pipe and dump it into the big tank.
This one also comes with an internal submersible pump.
It's a garden pump.
So it's already got pressure.
And the pump kicks on.
It's actually really quiet.
I'm quite surprised.
The pump's really quiet and you get a lot of pressure out of this.
More so than our house setup at the moment, which I'm quite happy about.
I had a tap hooked up to it the other day
and actually washed the car and used this water
so I didn't have to use the water out of the other tank.
And where you're standing now, by the way, this is where our bins are going to go.
Is that okay?
Yeah, they will, but we'll get a PowerPoint moved.
We will build a little thing with a little gate so I can wheel the bins in and out.
We collect a lot of bins here because we don't have a trash run.
We don't.
That's the joys of living.
That was one thing I had no idea about when we moved here either.
You don't get a bin pickup.
No, no bin collection.
Jono has to do it.
Yeah, Jono has to do everything.
Can we just say a very big thank you to Kingspan?
Because we really, really, really, really wanted a Kingspan water tank.
When they said that they wanted to come on board, partner with us, work with us,
we were like high five, yes.
Yeah, bloody excellent.
Thank you so much.
The guys smashed it out as well.
Yeah, they were such good crew.
I was amazed at how quickly they could set it up.
I'd had no idea I'd be this excited by a water tank.
But hey.
We're here.
And it's done.
I'm excited.
It's done.
Thank you Kingspan.
Watch your feet.
Don't, don't, don't.
You're silly.
Do you want it to go bigger?
Watch your foot.
No, don't.
Got water in it.
We've got water to burn these days.
Oh my goodness.