This video tutorial guides you through three effective methods to remove a stuck harmonic balancer bolt, using a Honda V6 (J35 | J35A7) engine as a demonstration. It starts with the most accessible approach, using a socket and breaker bar, ideal for those with basic tools, then explores two additional methods, including tips for both with and without special tools. Specifically, 1) an impact wrench rated 500 lb-ft or above with a heavy impact socket (3 times mass of a regular socket) will break the bolt free, and 2) if without impact tools, use the engine starter (as if an impact wrench) to crank the engine while hold the bolt in place to loosen the bolt. A bonus tip covers how to pull out the harmonic balancer if it’s seized.
Be prepared with these three methods and don't let a stubborn bolt derail your project. One of these will work. Professor has done it so he knows you can do it too. Stay safe!
This looks like just another bolt.
It secures the harmonic balancer to the crankshaft
and is perhaps similar in size to a lock nut's.
But don't be fooled by the size.
It can be a real challenge to remove.
If you are tackling jobs like replacing the timing belt,
crankshaft seal or water pump,
you will need to take it off.
Be prepared with the right tools and know-how
or you might find yourself stuck with a bolt that won't budge.
Welcome to Professor's Garage.
In this video, I will show you how tough the crankshaft pulley bolt can be
and share 3 methods to remove it.
Plus, I will cover a bonus tip for getting the balancer out if it's seized.
If this video helps, don't forget to like and subscribe.
Let's get started.
Harmonic balancer bolts come in various sizes.
A 19mm for Honda,
a 19 or 22mm for Toyota
and even a 27mm for BMW.
These bolts require high torque to secure and can seize over time.
Some, like the 19mm bolts on Honda engines,
are especially tough to remove.
Today, I will demonstrate 3 methods for removing them using a Honda V6 engine.
We'll start with the most common approach,
using a socket and breaker bar
and then explore 2 effective alternatives.
Let's dive into the first method,
which is the default for those with basic tools.
So this is the setup.
The one on the outside is the holder
with a ratchet or breaker bar and certain structure to support it to hold it in place.
The idea is that you make sure that the balancer doesn't turn clockwise
when you try to loosen the bolt.
And then I'm trying to use this 19mm socket
with a long extension and a long breaker bar.
And now you can try to see if you can break it loose.
If I lean my whole body on the breaker bar,
it's still not enough to break loose the bolt.
With a breaker bar, you will never be able to remove it.
You will need a cheater bar.
It's a longer extension of the breaker bar to break it loose.
But as you can see, it's tricky.
Many people tried it.
You may be able to get it done.
You may not.
You need a backup plan.
This is the regular 19mm impact socket.
Now this is the heavy duty one.
Now if you compare, it's the same 19mm socket.
But look at how thick this is.
This is a very thick socket.
At least 3 times of the mass of this regular socket.
We're going to try this to remove the bolt.
You can spray some penetrating oil on the bolt.
And then let it sit for 10 minutes or 20 minutes.
Okay.
We are going to give this very thick 19mm impact socket a try.
This impact wrench is rated 400 something,
less than 500 pound-feet of torque.
Usually this is not enough to take the bolt off,
which normally requires over a thousand pound-feet of torque.
But with this heavy duty socket, lots of mass in there,
we will be able to take it off.
Moment of truth.
Again, counterclockwise.
So reverse to take it off.
Super easy.
Within seconds, this is loose.
It took the bolt off within two seconds.
Amazing.
Now take a step back.
If you do not have an impact wrench and the heavy socket,
maybe you only have basic tools,
like a breaker bar and the regular socket here.
What can you do?
Here is the final result.
To use the car starter as your impact wrench.
But you need to know exactly what you are doing here
and know the risks.
And that your engine design supports this method.
Aside from the risk that things can spin out of control,
make sure you have the right hand bolt
and the balancer actually spins clockwise
so that when the starter turns the engine,
it's going to loosen the nut.
So let's say we can secure this bolt with the socket,
make it lock in this place.
And then we are going to turn the engine with the starter.
When the balancer spins, it spins in the clockwise direction.
And so if you hold this in place and lock it,
there's a counter force to turn counterclockwise to loosen it.
I hope this makes sense.
The first thing we need to do is to secure the bolt with the breaker bar.
Do not use this.
This does not belong here for this method
because what we want to secure here is the bolt.
So keep the bolt in place with this setup.
And then this breaker bar is touching the ground
so that when the balancer spins clockwise,
this is not going to spin in the same way.
It will prevent the bolt from spinning alongside the balancer.
And so the counter force is going to force it to go the other direction.
The idea is to use the battery
and hopefully you have a strong battery to drive the starter,
which is down there, to turn the engine,
which essentially crankshaft the balancer to spin.
You need to make sure that the engine will actually not start.
One simple thing you can do to stop to prevent the engine from actually starting
is to remove the power supply to the ignition coil packs.
This is not going to provide power supply to the ignition coil and to the spark plug.
So it's not going to spark and without spark,
you're not going to have a running engine.
These are the three cylinders in the front.
Also do the same for the three in the back.
Remove the power supply to the coil packs in the back as well.
Double check your setup before you go inside the car to crank the engine.
Now, moment of truth.
Now inside the car, I'm going to start the engine.
It's loose.
So the starter method works.
No problem.
It requires a really high torque to install it.
When you tighten the bolt and torque it to spec,
you do need this holder tool to hold it in place.
So when you turn, when you try to tighten it, it doesn't spin.
It doesn't turn.
So this is required for this job.
Two methods to torque this to spec.
It's either 46 pound-feet of torque first and then 60 degrees turn.
Or after the 60 degrees turn, the torque should be somewhere near 181 pound-feet.
And if you have a torque wrench like this,
I think it starts from 25 all the way to 250 pound-feet of torque.
Okay, 160.
See if we can go there.
Okay, this is 160.
And finally, 181.
Yeah, good.
181.
Great.
It's a good exercise.
Let me tell you.
And then over time, because of corrosion, it can seize.
And that makes it even more challenging to remove.
But in this tutorial, we have covered major methods for this removal.
This big socket is what I highly recommend for this job.
This will make your job so much easier with an impact wrench.
I have to say that impact wrench, you need to at least have like about 500 pound-feet of torque.
So I just checked the product description for this impact wrench.
It's rated 450 pound-feet of torque.
Many people said online that you need at least 600 pound-feet
to deliver the torque required to remove the bolt.
I was able to do it on this engine,
partly because this was not my first time.
Because I did remove this five years ago for the timing belt project.
It might not be as tight from the factory up to so many years.
So the second time you remove it, it may be easier.
So once the bolt is removed, and you also remove the serpentine belt,
the drive belt on the Honda engine,
this balancer can be easily removed.
Just pull it out.
You do not need the puller tool to remove the balancer itself.
On other engines, such as on Toyota or BMW, you will need a puller set like this.
First, take off this bolt, and then you can start to remove the balancer.
The balancer may get stuck, and this is where the puller comes in.
You thread them on to the balancer so they are attached.
Put a 14 socket on it, and then use a ratchet to turn it clockwise.
It's going to push against the engine and to push the whole balancer out.
But you know, you can also use an impact wrench.
By doing so, you also make sure that it's going out straight.
So on the Honda, the challenge is to remove the bolt, and the balancer is easier.
On BMW or Toyota, among others, you may need this puller.
And there you have it.
Now you know how to remove the balancer and get your job done.
If you found this video helpful, consider giving us a thumbs up
and subscribing to Professor's Garage.
If Professor can do it, you can do it.
Stay dirty, stay safe.
Until next time, may the Lord bless you and give you peace.
平安