Remodeling Kitchen Cabinets with a CNC Router

Rainfall Projects
6 followers
3 Video Views·Oct 29, 2022
Big thanks to Squarespace for sponsoring this video. I'll talk a little bit more about them
later. We've got some dark dingy cabinets in the kitchen. They might pass in a rusted cabin up in
the woods but here at our house it's definitely the biggest eyesore on the property. I promised
Kelly when she moved in that we would get on painting them right away. It's taken us 10 months
but we're finally getting to it. I had the idea that before painting we could pull the doors off
and use a CNC table to route a design into them, possibly faking our way into looking like we had
a fancier cabinet door than we did. I thought it was at least worth trying on two of the doors as
a test. Kelly and I both like the look of cabinet doors that are a frame around inlaid slats which
I thought would be a design that would work well on the CNC table. In v-carve I drew a rectangle
to match the dimensions of the door and made a copy that was offset inwards two and a half inches.
Kelly had the idea to add radiuses to the inner corners and lastly I centered one and three
quarter inch slats within the outer frame. I'm not sure how it's usually done but I decided that if
the partial slats on the outsides are less than half then I deleted one and re-centered them all
straddling the center point instead. Switching over to the toolpath side of v-carve I first set
up a pass with the 90 degree v-bit on all the lines with the depth of 3 16ths. Then I pocketed
out the inner slide area to half the depth of the previous v-bit which was 3 32nds so this area will
look recessed within the door slightly. And lastly I set up a profile pass around the outside of the
door to cut it out and ran a preview to see how it all looked. I quickly learned that my idea wasn't
going to work because there were big voids in the plywood. I should have known I think it's pretty
cheap stuff but I liked how the design on the door looked so I grabbed a piece of baltic birch I had
and ran the program again. This machined really nicely. I used some locating dowels to flip the
door over and mark the hinge screw hole locations and routing the notch around the perimeter of the
inner side before lastly profiling around the outside of the doors and cutting them free.
After a quick sanding I went ahead and mounted the doors and gave them some paint to see what
the project manager thought when she got home from work. The project manager approved so I
got to work drawing the rest of the cabinet doors in the kitchen. I learned these 5x5 sheets
are really awkward to move. I could just barely get my arms around them.
But I got the first one loaded up on the table. One thing I wanted to do on this project was to
mark the safe areas to screw the plywood down to the work surface. I placed small circles between
the doors and lightly marked them in the wood with a v-bit. Once I had the sheet screwed down well
I ran the program to start milling the cabinet doors. I've come to really like using v-bits.
They cut really nice and I didn't know I'd be using it so much on this and other projects.
I took the risk of not using any tabs which luckily worked just fine and the doors didn't
move when it was cut free. I think in this situation the sawdust kind of filled back
in behind the bit and helped hold the door in place on the last profile pass.
I decided the double-sided machining was overkill for all this and just used a benchtop router to
cut the notch on the back side which was much faster and easier. Not quite as sexy though.
While I was working on cutting the new doors, Kelly was busy inside the house taking down
the old ones. We were especially excited to replace the particle board sliders
with actual doors. Not sure who thought they were a good idea.
We were also really excited to replace this little vent thing under the sink. It was never fastened
and you always would knock it in when you were washing dishes and would have to fix it. Again,
not sure who thought that was a great idea. Kelly had the idea of replacing it with a piece
that had an inlaid design in it which I thought was a really cool idea. I told her the dimensions
and in Procreate on her iPad she set up a canvas of that size and hand drew a design.
Then she exported it and I loaded it up into VCarve where I could bitmap trace it and set
a VCarve toolpath. I exported the KDL file and got it cutting. I thought it was cool to be able
to cut something with the hand drawn feel on the CNC table. It seems like most things you use the
CNC table for are square or geometric. The brush she used in Procreate varies in width depending
on the pencil pressure she used when drawing it which on the CNC table translates to a variance
in the depth of cut with the v-bit because it cuts deep enough to match the width of the line.
With all the doors cut it was now time to move on to priming the cabinet frames.
But first a quick word about the sponsor of this video Squarespace. I think one of the coolest
things about Squarespace is that you can try out all their tools and build your website using their
modern templates all for free. No credit card needed. You can see for yourself just how intuitive
their drag and drop interface is and how even someone without any web design experience can
build a beautiful website to help promote their story or their online store. It really is the way
a free trial should be. Then when you're happy with your website and ready to launch use the
promo code RAINFALLPROJECTS at checkout to get 10% off your first purchase of a website or domain.
This also really helps support this channel. It helps me justify taking the time to step off the
combine and sit down in front of the computer to make these videos. So check them out. There's a
link in the description below squarespace.com slash rainfall projects and use the promo code
RAINFALLPROJECTS at checkout. Thanks Squarespace. The painting party was underway in the kitchen.
We were priming all the drawers and cabinet frames first. There's a little bit in the back corner
over there. We even talked my mom into helping somehow. Justin D Chambers. I think Drake and
Maloney had white tip tails for most of this project. And here's a shot of me painting just
to prove that I painted too. Man I hate painting. But with the group of us all working at it it
wasn't too bad. A couple gin and tonics might have helped as well. Once we got a couple top coats on
I started mounting the doors. This was quite a bit harder than I thought it was going to be
if I'm being honest. The method I ended up using was to mount the first door tied up against the
hinges. Then I could hold the second door in place, set the gap, and then carefully reach through and
mark the screw hole from the back side. Once I had this first screw in I could readjust the door
and mark the bottom hinge screw hole. This worked fairly well but most of them needed a little
tweaking afterwards. I should have said up front that we're really trying to do this project as
cheaply as possible which is why we are reusing all the old hinges. I know the concealed European
ones are good looking but I really didn't want to spend the money. Plus I already have a good
looking European in the house so I'm happy with just that. I kept hanging the doors while the
good looking European cooked dinner. After dinner Kelly came in behind me and started priming the
doors. We debated on whether we should paint the doors before we hung them but in the end decided
to hang them first so we could make sure they fit properly and also this way we were able to paint
both sides at once. We were just careful around the hinges. I think Drake and Maloney were sad
and concerned to lose their open access to the food cabinet. They've definitely been taking
advantage of that over the last couple weeks. It was also good to get all of Kelly's alcohol out
of plain sight. To mount the piece under the sink I sanded off some of the paint around the perimeter
and glued and clamped it in place. We thought about painting the inlay a different color
to offset it more but in the end decided we liked it a little bit more subtle just as a solid color.
I also countersunk a couple screws and flat spots that I could fill in with wood glue and later sand
flush. For the tourney cabinets in the corners I cut some doors that were half as thick that I
could glue onto the face of them. It worked well because it brought the face of the door out to
match the rest of the doors since they were originally flush with the cabinet frame. With
all the doors hung I cut a couple jigs to help mount the knobs and pulls. I put two different
screw hole locations in it depending on whether it was a deep drawer or a shallow one. I spent
probably five minutes trying to accurately measure and mount the first pole just using a tape measure
and it was still crooked. The mounting jig made it so much easier and quicker.
Kelly worked on mounting the knobs. The last thing I wanted to do on this project was to mount some
led lighting under the cabinets. This turned into a bigger job than I thought because I
wanted to run all of them off the same switch. I had to run the wire up into my attic which is a
really fun place to hang out and I try to spend as much time up there as I can. But the lighting
was really nice and we won't be cutting up onions and potatoes in our shadows anymore.
I think Kelly and I put about $500 into this project and it just completely changed how the
kitchen looks. I'm sure it's mostly due to the fresh coat of paint but I think the routed inlays
in the doors dresses it up quite a bit more than the flat plywood doors would have looked.
Two years ago when I was a bachelor I probably would have said that the kitchen would have the
lowest priorities on my list as far as projects went. But now that I'm an old married man I've
come to see the value of a kitchen as a great space to spend time with my gal while we cook
dinner catching up on the day's events. But I'll get back to the barn project soon, don't worry.
