Dining Room Table from CNC Milled Logs - pt. 3_3

Rainfall Projects
6 followers
5 Video Views·Oct 29, 2022
Now that I had the top side done, I needed to flip it over to work on the underside.
I had no idea how I was going to do this.
Luckily, Kelly was home and was able to give me a hand.
I asked Drake if he would, but he said he was too busy chasing tennis balls.
You don't need to flip that over again, do you?
Thank you!
I first gave the underside a light surfacing.
Next, I wanted to finish squaring up the ends, so I set up a backstop that I could butt the tabletop up against.
Looking back at the video now, I see I didn't quite have it fully up against the board on one side.
It was all I could do to move it, which is why there was a faint line left on the end.
But I was pretty sure it would stand out.
The last thing to route, which I was a little bit nervous about, was the mortises in the underside of the tabletop for the legs.
I wasn't sure if I should measure the actual tenon spacing on the now glued up legs,
which I knew would be slightly off from the computer model,
or just stick with the computer model measurements and hope to be able to force it in.
I eventually decided to stick with the computer model,
thinking that it might square everything up and be a nice tight fit for it, if I was able to make it go.
I zeroed off the right side, since the left side has the unfinished and uneven edge.
On something really important like this, I usually send it to zero-zero afterwards to make sure I didn't mess something up.
It looked dead on, so the only thing left to do was hit run.
When I was designing the table, I made sure the leg mortises were spaced a little ways away from the metal rods that held the tabletop together.
I figured if they were too close, it would be a weak point.
I gave everything a quick test fit, and it seemed like it was going to work.
Spoiler, I thought I had given everything a test fit.
My idea for the glue up was to glue up one side of the middle runner and arches to the end piece,
and hold it up with a strap around the rafter above, so I could glue it to the second end piece,
and then slide the whole thing into place and drop it into the mortises on the underside of the tabletop.
It seemed easy and straightforward in my mind.
I realized right away that I had forgotten to test fit one joint.
It was a very tight fit, and I wasn't getting anywhere.
I pulled it back out and gave it a light sanding before I reapplied some glue and tried it again.
I still didn't have any luck.
I came to the conclusion that I must have forgotten to give the mortise a pocket allowance.
I finally got the pieces together though, after a lot of sweat and cussing.
I gave the opposite side a good sanding down to make sure it would fit nicer.
It was so satisfying when one side dropped into the tabletop.
The other side was about an eighth of an inch too wide,
so I pulled it together with the strap and it fell in nicely as well.
I strapped it down to the table for a day while the glue dried.
It was raining outside, so I tried to quickly, but carefully, move the table back to the barn.
I had to recruit Kelly's help again to put the table back over.
She's the one that has the muscles in this relationship.
I wanted to give the wood a little bit of color, but I didn't want it getting too dark,
so I wiped the stain off pretty quickly after applying it.
I just did one piece at a time.
I had just enough in the court to give the underside a coat too.
I figured that with the table being so tall, that it was a little more likely for people to see the underside.
So, might as well.
I know at least Drake will be looking up at it.
I moved the table down to my grandpa's shop, which is heated, to apply the polyurethane.
We gave the underside two coats, and the tabletop four coats, with a light sanding in between each.
It probably looked a little weird going down the road with this thing,
but luckily we all look a little weird out here in the country, and we don't seem to mind it too much.
It was now time for the thing I was most unsure about on this whole project.
How the heck were we going to get this thing into the house?
With the help of my parents, sister, brother-in-law, and Daniel, who works on our farm,
we were just able to hoist the table up onto the deck, through the double doors, and into place in the dining room.
It looked so different being in the house. It looked massive compared to our last table.
But I thought it fit the space well.
The dining room was the right shape for the table.
The last thing I wanted to do was to stick some large felt pads under the legs,
so it would be easy on the hardwood floors.
Like I said earlier, there are definitely some things I would have done differently
if I knew this was going to be a dining room table, and not just a workbench.
The overhangs are too small, which means it's going to be kind of awkward for people to sit on the ends of the table.
The horizontal arches underneath interfere with the chairs a little bit when they are slid in.
And it's just crazy heavy.
But the table is unique, and a little bit quirky,
which I think is a good representation of Kelly and I's personality.
I also liked how the wood came from timbers that supported the floor of the barn outside.
That's a cool origin story.
And I'm fairly confident this table should stand the test of time.
I predict the floor underneath it will cave in long before anything on the table falls apart.
Hopefully my great great grandkids will one day find themselves wondering
how the heck they're going to move this crazy heavy table into their house.
