CNC Plasma Cutting Table Assembly and First Cut

Rainfall Projects
6 followers
3 Video Views·Oct 29, 2022
I really shouldn't be leaving the farm today.
We've got the first break in weather pretty much all winter and we've got a million things
to do, but my CNC table is ready to be picked up and I couldn't be more excited.
So I'm going to take a little trip up to Seattle to go get it.
I did a lot of research on different tables from different companies and I ended up settling
on one from CNC Router Parts.
While they're just getting into the plasma cutting side of things, their routing tables
have a really good reputation and their parts are kind of a standard go-to for people that
are building their own tables.
This table is going to be a big investment for me and I really need to get one that will
hold up over time and be reliable.
I know Frank Howarth uses a CNC Router Parts table and frankly, no pun intended, is it
good enough for Frank?
It's definitely good enough for me.
It was cool when I found out that the company wasn't actually too far away from me.
It's about a four hour drive.
And when I ordered the table, I asked them if I could save a little money on shipping
if I drove up and picked it up myself.
They said sure and said they'd give me a little tour of the warehouse and I get to meet some
of the people as well.
Honestly, I didn't really know what to expect.
I had heard that the company was basically started in a garage and so I guess I wasn't
expecting much more than that.
They had a really nice warehouse and were really organized and had all kinds of parts
for all different kinds of tables.
I was excited to get a demonstration of the torch height control in action.
They propped one side of the metal up and showed how the torch would follow the metal,
reading the voltage and adjusting the height as it needed.
They told me they had been working on their torch height controls for a couple of years
now and they really wanted to make sure they had everything figured out and it was a product
that they could stand behind before they released it to the public.
The back of my mom's Suburban sat quite a bit lower after we got this all loaded up
in it, but it all fit just barely and I headed on home.
It was great meeting those guys and I told them that if they're ever down my way to stop
by the barn for a beer.
I got back home around midnight and it was all I could do to not jump in and start putting
this thing together.
The space wasn't quite ready for the table yet, so I knew I was going to have to hold
off and get the space finished up and then I can jump in on this and do things right.
The water table had about half an inch to spare inside the Suburban.
I brought straps in case I had to tie it down to the top of the roof, which I'm really
glad I didn't have to use.
Alright, the table's in it's new home.
Fresh off a boat from Ireland, I was ready to jump in on this thing.
I thought the first thing to do would be to fill the water table up with water, but apparently
after reading the directions, I guess you start with the legs first.
I knew I shouldn't have read the directions.
It's my first time working with extruded aluminum and I thought that stuff was really cool.
I spent hours and hours as a little kid putting together Legos and K'nex and Erector sets
and this table would have been my ultimate fantasy as a kid.
Actually, what am I saying?
This table was my ultimate fantasy as an adult.
Something so satisfying to me about following along on the instructions as you build something
step-by-step.
I think it's something to do with going from having a million pieces and not knowing how
any of it goes together, and then one page at a time seeing it slowly take form.
It's the same thing with Lego sets, same thing with this table, I think it's even the same
thing when you're cooking a meal, which I'm not very good at, but I still enjoy the step-by-step
process.
I thought about fabricating my own legs for the table, which wouldn't be too hard, but
it's the summer time here and the farmer's taking up a lot of time, of course, it's priority
number one, and I just want to get the table up and running so I can use it.
If it was winter time and slower, I'd definitely think about making my own legs, and the guys
at CNC Router Parts do have some really nice legs.
So I just went ahead and bought a set to go along with the table.
Now that the table frame was done, it was time to slide the rails into the slots in
the extruded aluminum.
A couple blocks are included with the kit, which are used to make sure the rails are
set at the same height.
After attaching the block to the top of the table frame, I used a C-clamp to pull the
rails up tight against them and tighten them down.
It felt like Christmas morning every time I opened a new box, getting to see what shiny
new parts are in there.
I thought the linear bearings were really cool.
They each had a grease fitting on them.
Grease fittings are something I'm very familiar with on the farm, and I know how important
they are for keeping things lubed up and lasting a long time.
The directions were really easy to follow.
There was a PDF I downloaded from their website, and I just followed along on my iPad.
Hey, how are you?
Just like all kids, Drake liked the box just as much as what was in it.
The most common fastener used in the kit were these, I think they're called swivel nuts.
Pretty cool because they have this spring-loaded ball on the backside of them that hold them
in place when they're put into the slots in the extruded aluminum, which makes it a lot
easier for getting them lined up with the holes.
Gantry time?
Oh, it's gantry time.
After tightening down the gantry, the next step was to assemble the rack and pinion drives,
which the motors will be bolted to.
Those are some good-looking motors right there.
Instructions said three turns of tension on the bolt here, and those are good to go.
Okay, now it's time for the water table, finally.
I guess we'll do it your way, instructions.
These pegs hold the removable slats that the piece of metal I'm cutting will sit on top of.
The slats are removable so that after some use, when they're cut up and need to be replaced,
they can come out easy and stick new ones in there.
All right, once is enough with that joke.
But that's definitely how I felt every time opening these boxes.
It was a really hard decision, but I opted to go with the 65-amp plasma cutter over the
smaller 45.
I don't know how often I'll be using the higher amps to cut thicker metal.
I should be able to cut a three-quarter inch with this larger machine.
But I figured it'd be worth spending a little extra money now just to have the option available
to me if I were to need it down the road.
I'm not quite sure why, but I get so much satisfaction out of working on cable management.
I'm super anal about it.
I labeled every end and used a couple hundred zip ties to keep everything up nice and neat.
Super anal.
Sounds like the world's worst superhero.
Super anal, here to ruin the day.
I eventually hope to have some plumbing in the barn, and I'll have to put a faucet over
by the table.
But for now, I'm just going to bucket it over.
I thought this would be a good way to check whether I did a good job leveling the table
or not.
Ball runs to one side.
Probably I didn't do too good.
No leaks yet.
That's good.
Alright, I think it's that time.
I don't think Drake was too sure what was going on with this table.
He decided to play it safe and watch from a distance.
Don't really blame him.
I think, if I did everything right, if I push this button...
Yep!
Nice!
For some reason, I really wasn't expecting it to work like that right away.
I thought I would have made at least a couple mistakes that I had to troubleshoot, but I
guess super anal came through.
Well, I suppose the next logical thing to do is to try cutting something.
After putting some thought into what my first cut piece should be, I decided it might as
well be something practical.
One of the things I needed to do was to square up the gantry.
After drawing up something in SketchUp, I referenced the motors, which tells the machine
where the limits are, and squares up the gantry if the limits are set right.
Then I can move the torch to the corner of the workpiece and zero out the axes.
Axi?
Axises?
And here goes nothing.
FIRE IN THE HOLE!
Man, I'm never going to get tired of watching this thing cut.
I've done things like this the long way and the hard way for so long.
There's just a little bit of cleanup to do, but not much.
It's a lot cleaner than anything I ever cut out by hand.
This one wasn't quite perfect.
It was about a sixteenth of an inch off.
Fail.
So I brought one of the limit switches in, a couple of threads, referenced the machine again.
The two Y-axis motors reference independent of each other, and that's what holds the gantry square.
And I cut it out again.
As best as I could tell, this one was dead on.
Alright, let's put this machine to work.
