Pottery Bowl Trimming Tutorial

Sculpture Work
8 followers
17 Video Views·Feb 15, 2026
It is cold out here today in the studio, aka my garage. So yeah, it's really cold outside,
but I have to trim these bowls that I made yesterday that you saw. So let's get trimming.
All right, so this is one of the bowls that I trimmed yesterday. I left it uncovered overnight.
It actually got a little firmer than I normally like it, but it's still trimmable.
The bottom is still kind of soft. You can see I can make a little divot with my finger. So the
bottom is still soft enough to trim. It's really cold because, of course, it was left out in the
garage, so that's going to be fun. But I'm going to show you how to trim this up today. And whenever
I say trimming, I mean how do I clean up this bottom, make a nice little foot, or whatever
surface is going to be sitting on the counter whenever you set your bowl down. So you can see
the inside and outside all looks good. Now we just need to take off some of this excess clay,
lighten it up a little bit because the bottom is typically kind of heavy before you trim it,
and then make it look all nice. So for example, I have this berry bowl here that I made,
and this is what the bottom looks like trimmed. So there's a nice foot here. This is this raised
section that actually touches the countertop, and then this part is trimmed down a little bit.
So that's exactly what we're going to do with this. Obviously, I'm not going to be cutting
holes into this because it's going to be a cereal bowl. This won't hold much cereal,
so let's get started. All right, so as you saw yesterday, I had the bowl on here, and I cut it
off with a wired cutter tool. So today, I was able to basically just pry it off,
and now I can handle it really well. So now what I'm going to do is teach you how I trim this bad
boy. All right, so starting out, every time I start trimming something, I always have a spray
bottle of water. Spray the surface like one or two times just to wet it. It just helps the piece
stick to the wheel head better. You can experiment with your wheel head, but that's generally been
good for me, and I've been doing that for years. So now I'm going to center the piece, and you can
see what I'm doing. I set it down pretty centered as well as I can, and I'm just holding my finger
here, and then every time the piece touches my finger, I know it's too far in that direction. So
I'll stop the wheel, and whichever side was touching my finger, I'll push it away from my
finger ever so slightly. So I feel it touching right there. Push away slightly, even just like
one millimeter or something. All right, that seems pretty perfectly centered. Okay, and I'm just
going to break them into three little pieces, and I'm pushing down with this hand on top, and then
I press these sort of down and sort of in. If, depending on how like dry or wet your piece is, you
want to make sure not to press into your bowl because you're going to leave little divots. So
normally I just press kind of down on the wheel head and hope that it's enough to hold everything.
So now it should be fairly secure with these, and what I like to do, now we start the trimming
process. So what I like to do, I always like to take my needle tool, and just in case the bottom isn't
completely even or something like that, I like to take my needle tool and gradually
press down and cut the outer skirt or ring off of my piece. That just makes the entire
trimming process from here go so much more smoothly, and it's just a lot easier. So I really
like this, you can't really see it, but it's Kemper tool, R4, R4 Kemper tool. I really like this
trimming tool, it's my favorite one. So I'm going to start by just taking some off the sides.
I'm switching to the slightly wider side, and here you're basically just visualizing what
you want the bottom of your bowl to look like. Do you want to trim off this whole corner so
that you don't see a foot from the outside? Do you want to have a very distinct foot?
So what I'm going to do, I want a distinct foot. So what I'm going to do is sort of trim inward a
little bit, and then here I'm going to press down because I want it to be a nice sort of rigid
foot, and then I got to start smoothing out that curve right there. So that looks pretty good,
now I'm just going to start trimming off this excess part. Okay, and now I want to decide
how wide I want this foot to be. I want it to be about a quarter inch, so while the wheel's spinning
you can do this with a needle tool. So if I did this with a needle tool, I would just sort of mark
where I want it to go, and then I would trim within there. I also just use the pointy part
of this tool to sort of make that line, and it's very helpful to make that line because
it helps stop you from going all the way over the foot and messing up that way.
So now I'm just going to start from the middle, and while holding the trimming tool evenly,
you're going to just gradually move over. Okay, you're going to hold it evenly,
you're not going to press down more, you're going to hold an even pressure, and then move over. It's
almost like a record player playing your record, the needle is moving to play your song. Gradually
going deeper, and you want to remember about how much or how thick your base is. So even if you need
to feel how thick your base is before turning this over to trim, you can do that before you center it
on the wheel. Now I'm sort of going to press down to see if I feel any give. I don't really feel
anything, so I can go a little bit, a little bit more, but that looks pretty good. I'm probably
going to start cleaning it up at this point. So what I'm doing, basically just going over all of
the different curves or corners and smoothing them out, and then smoothing this part out.
Okay, that's looking pretty good. Okay, at this stage you don't want to use your finger to like
take off any of those little dirt noodles that were on here, because that's just going to press
those dirt shavings or clay shavings back into the clay, and it's not going to be very even. So
at this point I'm actually done. I'm going to use my little Maker's Mark stamp to stamp into the
bottom. So you can either sign your name or your signature, or if you have a stamp you can stamp it
that way. Just something to mark it that you made it, and I'll show you exactly what that looks like
in a second. So there's the little stamp you can see, and we are good to go. So now I have my bowl
finished here, and what I'm going to do to dry it is I'm actually going to put it upside down to dry,
just because the bottom is more wet or more moist. It has more water content in it than this top rim
does, so by putting it upside down to dry, it actually will be able to drive more evenly. So
let's do that. So I'm going to put it up here. All right, and now it can dry, and then it'll be ready for
bisque in a few days. Thank you so much for watching this video. If you liked it, please give it a
thumbs up, and be sure to subscribe for more pottery content, either teaching, vlogs, anything
like that. If you have any questions or other comments and ideas of how to make a bowl, trim a
bowl, anything like that, feel free to leave those in the comments as well. I hope you have a great
day, and stay tuned for whenever I glaze everything and show you the finished product. See ya!
