Installation of a 24v Victron Multi plus ll system.

Cherish the Journey
37 followers
31 Video Views·Sep 2, 2024
[Music]
we are talking about inverters and how I
did my setup this is a how I did it
DIY not necessarily A how-to video so
with that being said just keep that in
mind um always do your research but
let's get into things right now and
let's go so what I did is I mounted the
batteries inside my storage compartment
because I wanted to shift the load of
the batteries further back that were off
of the pin and actually it freed up some
space in here as well and with that
being done I had to move the cables I
had to Route the cables more further
back through the wall here we have two
12vt
200 amp hour batteries we wired them in
series and doing that we actually double
the voltage and the amperage stays the
same so we have 24 volts at 200 amps and
that's what this victron is actually
made for is a 24volt system uh make sure
that when you're doing your designs that
you're actually getting the right
equipment with that being said um um
there's 12vt inverters 24volt inverters
and there's 48 volt inverters um from
victron so let's continue on as we're
seeing right now I'm installing the
shunts and DC load distributor so that
way your 24v comes into the load bar and
that actually will distribute all the
load evenly with these Mega fuses that
get put in place and so those Mega fuses
will blow before um anything else hits
the DC side of the inverter or our solar
charge controller also we put in a shunt
Bluetooth shunt and we have that on the
negative side and then on the positive
side we have the disconnect so since we
are actually doing 24v system we had to
get a DC todc converter this is a
24v step down to 12 volts and you can
adjust the voltage so it actually we
have it set to about 13.2 volts and it
can handle 70 amps and you need that
much because of the Jacks the
stabilizers uh the slides everything
that runs off 12 volts so everything up
to to this point has been DC we've got
our batteries hooked up we got
everything connected to our battery
disconnect that's the main disconnect to
the 24v load distributor here and then
also we have all our outputs going to
our solar controller and to our victron
as well so now all the DC stuff is taken
care of um again I did not touch
anything with our 12vt bus bar I left
that completely intact everything's
already
connected um for your slide mechanisms
your Jacks lights everything to do with
the 12vt side I left alone so now let's
show you what I did with the AC side and
it is very simple what I did here is I
took the breaker box out where our main
breaker box is on the inside of the
RV and I made sure we are not dealing
with live power so make sure always
disconnect your power and you'll make
sure that ensures no load no power is
coming from anywhere we are going to
take our wire that goes from the plug
and that goes to the actual Main
breaker box we're going to take those
wires out and I'm going to run it on the
pull that wire all the way back and then
we're going to run it inside you can see
my uh Watch Dog here so we got a
hardwired
one and we just went right into that I
went to got the same gauge wire and then
we're coming in a little short jumper
from there into the AC and put here on
the victron inverter and then we just
had to get a a little bit longer wire
for AC side and we do a AC output and
this is 50 amp that we're dealing with
then just run those back to your main
panel and hook it up just like it was
and the AC site is done that's really
simple to do and just finding your cable
routes is going to be the hardest part
of this job and I mean that's that's it
we'll talk about solar in another video
here I hope this video helps you out I
hope that it inspires you to maybe save
some
money and go DIY
[Music]
