How To Change The Brakes on Your RV | RV Maintenance!!!

Cherish the Journey
37 followers
56 Video Views·Jun 10, 2024
so hey everyone we are doing a project
today we are under the rig which means
probably maintenance yes so we're doing
some Tire maintenance and specifically
we
are get this out this heavy this bad boy
here um it is for our brakes so when I
replace the seals the seals on here when
I replace the axle seals on here um I
noticed that my brakes were not that
good so I went ahead and on E trailer
and ordered me the whole kit because
that is pretty much what you need to do
and these are the self adjusting so
there's a little actuator here this job
is going to be super easy it's just a
little bit tedious because we have to
take the tire off and then we have to
take the the hub off and then we pull
there's five bolts on here um which will
go through and we have to cut the wire
and these two wires will splice back in
so that's what we're doing today so
let's get to it and it shouldn't take
that long
[Music]
[Applause]
[Music]
go
[Music]
[Music]
[Music]
[Music]
[Music]
important thing to note is when you're
taking your hub off put it in a box put
it somewhere nice where it's not going
to get dirt dust and you don't want to
do it on on a windy
day um so that way you don't get grease
you don't get dust and crap inside
inside the axle and inside the spindle
when you put everything back on um so
you got your inner and outer what you
saw me taking off was that was the outer
seal the outer bearing rather um and it
it's just a little flat washer and and a
lock a retaining nut that goes on there
um so we want to make sure we do keep it
nice and clean as clean as possible from
dust and debris so next um we have on
here is there's
four five bolts five nuts and those are
those bolts are attached to the actual
axle itself so um there's two wires
right here uh um so that if you ever
need to know what your part number is
it's on that sticker this white sticker
here these are the two wires you you're
going to cut the wires and again it
doesn't matter which one goes to which
they're not um conducive to going back
to the same wire um it's just for um
Power and send so let's go ahead and
take those five bolts off or bolts
nuts and we'll pull that off and then
cut the wires and we'll splice those two
wires on put the new one on throw
everything back on and we're good to go
[Music]
oh
[Music]
oh
[Music]
[Music]
[Music]
[Music]
match up the holes make sure you don't
pinch the wires in the back and they
[Music]
give they give you new new nuts to put
on so we're going to go ahead and use
those and put it back on then we'll put
our Hub back on and get everything
buttoned back up
[Music]
[Applause]
[Music]
all right so now we have our bearing
which we've I've already redone the
bearings so we're just going to put them
back in we'll put a little bit of uh
these are the E Lube so we're going to
put a little squirt of extra lube after
the end so we'll go ahead
and seat that
[Music]
in and make sure you put it in the right
way then there's a little
flat it's a little flat piece and
there's flat on here
[Music]
so and so with this you want it just
hand tight so this can freely spin still
[Music]
now we'll take our retainer clip
[Music]
[Music]
that's
it and again these are the easy Lube so
this little plastic cap we can pull this
cap off and we can Lube up the spindle
and everything get a little more grease
inside there and we want to make sure
we're using the high temp grease in this
[Music]
give it that tap all you got to do is
just tap it in just tap it in
[Music]
now and there we go now we're ready to
put the tire back on
and we're all done I hope this video
helps you out and I hope you learned a
little bit of what to do what not to do
[Music]
