I Built a Mini Gaming PC from a Broken Laptop!

Tech Care
3 followers
Nov 15, 2026
AI Generated·May contain errors
I turned this completely broken laptop into a mini-gaming PC,
and trust me this thing was a
total disaster. I upgraded almost everything
from the CPU to the storage and even found a
way to connect a desktop GPU
and the FPS.
This is an HP ProBook 4430S.
Let's just say I was not
And believe it or not, this thing is over 15 years old.
I picked it up on eBay for ridiculously cheap, just $1.
expecting these results.
But there's a problem,
I can't really use it like a normal laptop
because the screen is seriously messed up.
And to make matters worse,
it took a pretty nasty fall and got completely wrecked.
Luckily though, the components inside seem
to have survived. I tried powering it on,
and surprisingly it still worked.
But at this point, there's no way I can keep using it like
Uh, I mean just look at this thing.
It looks like it's been through both world wars.
So I figured I'd pull out all the components
and see what I could do with them.
And I actually did that in a previous video.
You can go check that out if you want
to see how I took this whole thing apart.
Alright, so here's the motherboard.
Now it worked just fine in my previous projects,
but that doesn't necessarily mean it's still working today.
So let's give it a quick test. Oh, there we go.
We've got a display. Uh, looks like everything's working just fine.
But then I look at the CPU, and yeah,
the disappointment kicks in all over again.
And the integrated graphics? Not much better.
But is it actually any good for gaming?
Well, let's find out by testing a few games.
First up, Minecraft.
I'm sticking with the older 1.8.9 version,
with some pretty basic textures.
Honestly, I don't think this laptop
could handle any of the newer versions.
Oh my god, just as I expected. This thing is lagging like crazy.
2 FPS? Oh wait, it's still loading the world.
The FPS is starting to climb, but yeah, that doesn't
really change much. Every time I move around,
the frame rate takes a massive hit, dropping to around
20 FPS. So I turn the settings all the way down, and...
Okay, that's not too bad,
but we're still a long way from calling this thing a gaming PC.
I mean, we're not even hitting triple-digit FPS.
Next up, Tomb Raider, one of my all-time
favorite games. I'm running it
at HD resolution with everything set to low.
Oh, come on. Barely 10 FPS?
That's absolutely terrible for a game like this. And the CPU?
It's pretty much running at full load.
The temperature is shooting up too,
already over 80 degrees Celsius. Holy crap.
I'm literally straining my eyes trying to play one
of my favorite games. At this point,
I swear I could flip through a book faster than this
thing can render frames. I mean, come on.
There's no way I'm building a gaming PC
with hardware that's painfully slow. So that got me thinking,
What if I could actually do something
to make this old laptop more powerful?
Choose the right civilization and get 50 million power?
I'm just kidding.
Maybe swap in a much faster CPU?
Or better yet, add a dedicated graphics card?
Now that sounds like a pretty fun idea.
So I started digging through a few online marketplaces,
looking for a more powerful CPU that would work with this machine.
Now, as some of you might know, this HP laptop uses Socket G2.
And that means the CPU is actually removable,
so we can swap it out for something better.
Unlike those laptops where the CPU
is soldered directly to the motherboard,
and you're pretty much stuck with whatever you get.
After doing some digging, I finally found a pretty good option.
An Intel Core i7-2820QM for just $18.
It's a quad-core,
8-thread CPU with a maximum turbo clock speed of 3.4 GHz.
That's about a 48% increase
in maximum clock speed compared to the old i3-2350M.
And in terms of overall performance,
this i7 absolutely blows the old i3 out of the water.
So this should give the machine a pretty significant performance boost.
And here it is.
However, here's the thing.
I couldn't find any documentation confirming
that this i7-2820QM actually works with my laptop.
Even HP's official documentation...
Only lists support for up to the i7-2620M,
but in terms of architecture and physical compatibility,
it should theoretically work,
so I figured it was worth taking the risk. I mean, if there's
even a chance I could turn this old laptop into an absolute beast,
why the heck not give it a shot?
Now, let's pop this thing in and see
if it'll actually work with our motherboard.
I also swapped out these 2 gigabyte RAM sticks
for a pair of 4 gigabyte sticks,
bringing the total up to 8 gigabytes.
I actually wanted to go all the way up to 16 gigabytes, but
unfortunately this laptop only supports
a maximum of 8 gigabytes. But hey,
8 gigabytes is still a pretty nice upgrade.
Alright, let's fire this thing up.
Oh my god, it actually works!
I honestly didn't expect it to be that easy.
I thought I'd at least have to update
the BIOS to get this thing running.
Looks like luck is on my side again today,
so I opened up CPU-Z and there it is, the i7-2820QM.
I mean, just look at these specs.
This thing is so much better than the old CPU.
With all those extra cores, threads, and higher clock speeds,
I should be able to handle heavier workloads
and run games a whole lot smoother.
And the benchmark score? It came in at 275 points.
That's a pretty significant upgrade. Now I'm the
kind of guy who likes to play it safe,
so before I cram all these components into some kind of PC
case, I want to run a few more tests
to make sure everything's working properly. But there's one
thing I noticed. As soon as I opened Steam,
this tiny little fan started getting really loud,
making this annoying high-pitched whining noise.
And I've got a bad feeling about this.
Yep, I knew it.
The CPU temperature is climbing like crazy.
And this poor little fan is absolutely screaming for its life.
Yeah, there's no way I'm putting up with that noise all day.
We gotta do something about this.
Now, as you can see, this original cooling system
was designed for a 35-watt CPU, but
our new i7 has a TDP of 45 watts,
and clearly this tiny cooler is struggling to keep up
with the extra heat, so I need to replace it
with something a whole lot bigger.
Something like this desktop PC cooler.
I mean, just look at all those copper heat pipes and aluminum fins.
This thing should do a much better job
of keeping our CPU cool, and more importantly,
I won't have to listen to this little
guy screaming his head off anymore.
Now, let's put this new cooler
on and see how much it improves the temperatures.
Um, okay, I've got it in place, but there's a problem.
This laptop doesn't have a compatible fan connector,
and I don't plan on using any of them anyway.
See, the original laptop fan runs on 5 volts,
while this new fan needs 12 volts.
So I'll have to power it using a separate power supply.
Then I hooked up the power to both the fan and the power supply,
and it fired right up!
So I tried turning on the laptop too, but nothing. No response at all,
even though the power light was still on.
Oh, and after a little while it just shut itself off.
My guess is, since I didn't plug in the original fan,
the BIOS detected that it was disconnected
and either stopped the boot process or shut the system down.
So I tried booting it up again.
Nice. It actually booted successfully with the new setup.
And the temperatures? Way better than before.
They're now hovering around 40 to 50 degrees Celsius.
But now I've got another problem.
How the heck am I supposed to mount this cooler?
I mean, this thing was never designed for a setup like this.
The mounting points don't line up with the holes
on the motherboard at all, but don't worry.
I've got an idea.
I'm going to use the mounting bracket that came with this cooler.
First, I'll drill some new holes in the bracket
to line up with the mounting holes on the motherboard.
Then, I'll cut off the extra bits.
Finally, I'll tighten down the screws and...
There we go. My custom cooler upgrade is officially done.
This thing is rock solid,
and it should keep the CPU pretty cool too.
I'm also going to use this little fan and wire
it up to the original fan connector on the motherboard.
That way, the motherboard can
detect a fan like it's supposed to,
and I'll have an extra fan to help improve airflow.
Next up, we're going to need a graphics card.
But take a look at this motherboard. There's
no full-size PCIe slot, not even an NVMe slot.
So how the heck am I supposed to connect a GPU
you to this thing? Well, this right here.
See that tiny slot? That's a mini PCIe slot,
and I'm going to use this mPCIe to PCIe x16 riser
to connect a desktop graphics card to our laptop. First,
I'll remove the Wi-Fi card and plug this riser into its place.
Then, I'll hook up all the cables to the adapter.
For now, I'm just gonna use this small graphics card
to see if the whole setup actually works.
Alright, I've got everything hooked up,
but will this thing actually work?
Well, there's only one way to find out. Let's fire it up, and...
Oh my god, it actually works!
Even with everything connected, the system is still running just fine.
And look at that, the GPU is actually being detected by the system.
This is a huge step forward compared
to where we started with this project.
But there's one pretty big downside.
This connection is limited to PCIe x1 instead of x8
or x16 like you'd find on most modern
desktop motherboards.
This is mainly because the USB 3.0 cable only has enough bandwidth
for a PCIe x1 connection.
But hey, at least we've got a dedicated GPU now,
and that should take some of the load off the CPU,
especially when it comes to gaming.
This whole setup looks pretty messy, and you know what?
It really needs a proper case, but instead of designing
a completely new one, I'm going to reuse this case.
I actually really like it, and I don't want
to just leave it sitting in a corner collecting dust.
So I'm just going to 3D print a new I.O. panel
and add a bunch more ventilation holes.
That should make it look a lot more refined than
my previous design. I mean, come on.
Doesn't this look better?
I don't know about you guys, or maybe I'm just biased
because I designed it myself,
but I think it looks absolutely amazing. Perfect!
Alright, let's start putting everything together.
First up, the motherboard. I'll drop it into the case
and secure it using the screws already in
place. Then, I'll tidy up the rest
of the components connected to the motherboard.
Next, I'll put the power supply in and extend
the power cable to the female connector on the case.
I'm also adding a power switch to make turning
the power on and off a whole lot easier.
Next up, the M.2 PCIe riser.
I'll plug it in and secure it with a couple of screws so it doesn't
come loose. Finally, the GPU I picked for this project.
A GTX 1050 Ti low profile. It's powerful
enough to be a pretty good match for our CPU.
And more importantly, it's super compact. I mean,
look at this. This case wasn't even designed
for this graphics card, but somehow, it fits
almost perfectly. And it's surprisingly secure,
even without adding any extra screws.
Now it's finally time to put
the CPU cooler fan where it should have been all along.
Power will be supplied through a Molex connector
from the external power supply.
Of course, we can't forget the power button.
Okay, everything's finally in place.
Now, put the case panels back on.
And this time, I actually get to use
that black panel I printed earlier.
I swear, I didn't plan any of this.
Mission passed!
Now, who's gonna call this thing a weak, outdated laptop anymore?
I basically sent this little guy to the gym,
and man, the results are way better than I expected.
I'm pretty happy with how it turned out,
and I think this is actually a great way to give an
old laptop a second life.
Just turn it into a mini PC, kind of like what I've done here.
But now I'm really curious
to see how much performance we can actually squeeze out of
this thing. Let's move! Alright,
let's jump back into Minecraft and see how much of a difference
we've made. This time, thanks to the dedicated GPU,
I can actually play the latest version of
the game. And with the default graphics settings,
I'm getting a pretty consistent 100 plus FPS.
However, the CPU is now becoming a bottleneck,
so I do get some occasional frame drops here and
there. But what about Tomb Raider?
Well, I'm not going easy on this little guy. This time,
I'm cranking the graphics all the way up to high.
Oh my god, I honestly can't believe this. This
thing is actually pushing over 60 FPS,
and throughout the entire test, there are barely
any noticeable frame drops.
But now, let's take things up a notch with something way more
more demanding. Cyberpunk, and yeah.
With a CPU this old, it takes forever just to get into the game.
Alright, so I'm running it at medium settings.
And as you can see, the CPU is pretty much maxed out the entire time.
And it's not just the CPU.
Even the RAM is getting dangerously close to its limit.
The frame rate is sitting at around 30 frames per second.
Which, honestly, is pretty surprising for a machine like this.
So, there you have it.
I just turned a practically useless old laptop
into a pretty unique little gaming PC.
And I hope you guys had as much fun watching
this transformation as I had building it.
Thanks for watching, and I'll see you in the next one.
