How To Test and Replace EVAP Canister Vent Control Valve P0446

Allstar Auto
20 followers
27 Video Views·Oct 22, 2022
Now code 446 deals with this guy right here. This is the EVAP canister vent control valve.
If you take a look it's attached to the canister which is right here. Now this happens to be at
the rear of the vehicle. Here's your rear driver's side wheel and right behind it you'll find the
canister and attached to the canister we have this vent control valve. And real quick I just
want to point out really there should be two bolts here. What happened years ago is this one snapped
right off as you can see and I had a small EVAP leak and to fix it what I did is I just used a
gasket maker here and it just sealed everything up and I was okay. So if you're getting code 446
you need to check a couple things and we'll run through each test. Number one we want to make
sure if power is getting to the harness because if it isn't then obviously this won't work. Number
two is you have a hose here you want to make sure that the hose is free and clear and to do that you
just pull off the hose and just follow it make sure it's clear. What you could do is is just
remove the hose from the vehicle and if you want if you don't have an air compressor just attach a
hose a water hose and just see if water drains through it. If it does great if it doesn't it's
clogged. So that's a very easy thing you can do for the rubber hose. Number three is we'll test
the vent itself and number four is you have a pressure sensor which lives right here in this
case which should be attached to the frame rail which I have to get back on there and actually in
fact I have a video on this showing how to test it so I'll splice in that video at the very end.
But let's go ahead and just run these tests let's make sure number one that power is getting to the
harness. So to do that there's a little tab up here these could be really tough to remove sometimes
these are waterproof connections and they can really get on there but press down hard there's
a tab and then push back and that's it don't pull on the wire itself just pull on the body.
So what you want to do is turn on the ignition key to the on position you don't want to crank
the car just turn it on to the on position. Okay to the on position here don't crank it again just
turn it on and what we'll be using here is just a very basic multimeter and we'll be using the
of course the voltage setting. Now before we test the voltage what I'm going to do first is attach
a good ground point now this is the negative terminal coming from the multimeter and let me
switch hands here this is the spring for your e-brake so I'm just going to insert it like so
this is a very good ground point and then back here at the harness you have two terminals number
one and number two in this case we need number two and just touch with the positive lead coming
from the multimeter touch that terminal and you should have 12 volts worth of power or battery
voltage going to this sensor. Now if you're not getting a reading here first make sure that you
have a good ground because if you don't have a good ground that's this guy right here if you
don't have a good ground then you won't get a reading obviously the other thing is to check
these wires back here if these wires are okay then you have to check the fuse which in this
case is a 15 amp fuse so but usually it's just that these wires back here corrode or there's a
splice somewhere so you just need to repair it now if this is okay in your case then let's go ahead
and test the valve itself. As you can see we have two leads running from this vent now it would be
a heck of a lot easier just to remove the vent from the canister but as I explained earlier I
had to apply this gasket maker because I had a small leak and I just don't want to break the seal
so what we want to do is apply 12 volts worth of power to verify that this valve is working inside
the valve there's a plunger that moves back and forth depending on what the car's computer or the
ECM tells it to do. So I've jerry-rigged a power source if anyone out there is in RC this happens
to be a lipo battery pack usually it's 11.1 I actually checked it's 11.8 volts right now
so this is more than enough power and just be careful you don't want to cross the lines
but as you can hear I'll do it again so now it's off and now it's on off on so we've verified
let me just disconnect these guys we've verified that this valve is working correctly so now we
know power is getting to the valve we know that the valve is working correctly number three as
explained earlier just check the hoses again make sure there are no leaks also good due
diligence would be to replace these hoses as well I actually did a couple years ago I didn't have
any leaks but hosing is inexpensive you just cut the size and and replace them really and it just
it just cuts the confusion out if you ask me just replace all the hoses back here
just for any future problems that's the third thing the fourth thing is you have a pressure
sensor and I do have a video out there showing how to test this sensor so I will splice in the
video right now you do need the multimeter again and you'll also need a vacuum gauge as well so
that's what code 446 is all about if you ran through all four of these tests I'm sure you
diagnosed where the problem was and we'll see you next time
