How to measure a Camshaft: lift, journal OOR and Taper +more

Charley’s Garage
78 followers
25 Video Views·Oct 14, 2026
For new engine builders an overview of how to properly measure a camshaft for warpage, journal out of round and taper, and of course line lift!
You can help my efforts to create free technician education videos by becoming a channel member!
AI Generated·May contain errors
Video Summary
AI GeneratedThis video provides a comprehensive guide on how to properly measure a camshaft to ensure it is straight, within wear specifications, and meets the required lift standards. The instructor demonstrates the use of dial indicators and micrometers to verify the health of both new and used camshafts before engine installation.
Alright, so I told you guys before
that I would show you guys how to properly measure a camshaft,
and that's what I'm going to do today.
So, most of the stuff that you want
to do on a camshaft can be done with a micrometer,
but we are going to talk about first one thing
that you might want a dial indicator for.
So, that would be with the camshaft sitting
in the head with the caps off of it,
or better yet in some V blocks,
putting a dial indicator on the shaft that the caps go on,
on this journal right here.
And then what we would do is just slowly rotate this cam on those V
blocks and watch that dial indicator gauge.
If that gauge moves off of zero, it means that this
thing has some imperfection and run out.
And we don't want that, right? We want a nice straight
camshaft so that's the one thing you might want
to do a dial indicator with now one thing you
might also want to measure if your engine manual calls
for it is going to be your oil clearance
between this journal right here and the bushing
or the cap and bore that go around it in which
case you might also need a t gauge
but if you were going to measure this camshaft the first
thing that we're going to be wondering about is the lift
so here you got the nose or the heel of
the cam lobe. And this is part of what we call
the base circle right here, or sometimes called
the inner base circle. Up here,
you got the nose or the actual lobe that lifts up on a push rod
or pushes down on a lifter.
And what we want to know is what is the difference between the base
circle right here and the lift, right?
So we configure our lift by subtracting this measurement
from this measurement all right making sense
so far all right so the tool that i would use to do
that with is a micrometer
and so i know there's a lot of new technicians or new people that don't
know what a micrometer is so real quick
this is an outside micrometer it can measure the diameter
of things and if you look at this one it says one
to two if i can get it in the camera one to two
right there what that basically means
is that everything i measure with this micrometer is
going to be between one and two inches
so all my measurements are going to be one point something
right if i had something bigger than this guy
to measure i would have to go up a step so these guys
come in different sizes this one is a two to three inch micrometer
so everything i measured with this
one would be two point something inches all
your point somethings that i keep talking about are
going to be coming from up here on this measurement scale
and we'll talk about that in a minute all right
so if i'm measuring the cam lobe let me adjust the camera angle
so you guys can see it a little
bit better all right if i'm measuring
the cam lobe we got the high point right here
so if i measured this with this guy
and put it on here get it centered up and then what i would do
is i would kind of run it in with the one finger until i get it kind
of snug and then once i get
it kind of snug on there
then what i want to do is use my little clip here at the end until it
clicks on me and then i lock in my measurement in place pull it out
and take a reading right
so when you're looking at one of these micrometers all
of these big numbers right here are a tenth
of an inch and every little dash between
the big numbers right here are 0.025 inches so what you
got to read is where you are as far as the tenths
and the 0.025s get those all added up together
then you're looking at this guy right here every single line
on this barrel right here
is 0.001 inches so in the case of the measurement
that i have right here i am just past 0.550 and
i can tell that because i got past the five right
and when i got past the five i see two hash marks
and i can see on here let me see if i can get it
to where there's no glare i just passed the zero
so what that means is that i got my 0.550 read right here
then i got to take what i see here
and add on to it so here i'm taking this line runs right across here
and lining it up with this guy
and on this guy i'm right dead on uh three marks past the zero
which is 0.003 so i would take my
0.550 add 0.003 that gives me one
because it's a one to two inch micrometer 1.553 inches so
that's how i would measure this part
and then all i would simply do is rotate my cam and measure that
uh the base circle which is going to be much smaller than
the uh the other part that we just
measured. So we'll take this measurement.
And once we get this measurement,
so on this one,
I have 1.325 plus 14.
So 25 plus 14 is 19.
So that would be 39.
So that would be 1.339.
So I can do the math now and subtract those two numbers,
that 1.553 plus the number I just said
that i already forgot and that would give me my total lift
and it's important to note that when
the camshaft is rotating
and you get this lift that sometimes there's going to be something else
that helps with valve duration
so the ramps here play a part in duration how wide they are how long
it takes them to go up and back down things like
that play a role in duration and then also another
thing is rocker ratio so even
though we might say 0.246 inches of lift or 0.191 or
whatever your spec is for your camshaft
or lift your rocker is going to increase that a little
bit the rocker ratio is going to add to that so uh
that is how you measure the cam lobe measure
the base circle measure this subtract them
from each other that's how you get your lift
and then of course you want to make sure
that just this guy right here the journal itself
we already put talked about putting a dial indicator
on it to check to see if the camshaft
is warped or bent but we also want to kind of measure
these just to see if there's any excessive
wear on the journal itself.
If there was, I would probably want to get a new camshaft. So
same method. I would take this guy
and I would just put it around this and take a measurement.
And then I could also do a measurement from end
to end to see if there's any taper. And I can do
measurement here, measurement here, measurement here,
and check for out of round. But all those
different measurements will help ensure
that you've got a camshaft that's healthy enough to
put back in your engine? Or if you bought a new camshaft,
does it meet the standards that you
bought it because there are some shady dealers out there
that will sell you camshafts and make a
claim and you take it home and measure it and they are not the same.
So new camshafts, old
camshafts, measurements are always the same.
The thing about camshafts though, is that they can be
a lot bigger than this one.
So you may not be able to get away unless you're just always rebuilding
the same size engine with just one of these so you might want
a kit that comes in multiple sizes
which i will put in as a product link just
in case you guys are interested don't have to buy it just
for you know just so you can see it
um if you have any questions let me know in the comments
sorry if the audio on this one isn't quite
as good i lost my microphone somewhere and haven't
been able to find it uh but thank you
for watching charlie's garage please like uh please share this
with anybody else that's learning how to work on engines.
And I'll see you in the next video. Thanks. Bye.
