Free 410 lee loader type device pt 1

The Skill Tutor
20 followers
1 Video View·Oct 30, 2022
Hello everyone and welcome. With the popularity of the 410-45 combo guns being more popular now
than they ever have, I can't understand why the 410 shotgun shells still cost more than
the 12-gauge shells. And if you try to find a 410 reloading apparatus or even a 410
reloader type device, they run a hundred dollars or more. Now I have guns that back in the day I
didn't pay a hundred dollars for, so there's no way that I'm gonna pay a hundred dollars for a
device to reload the shotgun shells. So that's what I'm gonna do today. I'm gonna build a
reloader type reloading device for the 410 shot shell that will take up to three inch shells.
And in building this little kit, I want it to be able to size both brass and plastic shells,
deprime brass and plastic shells, and load brass and plastic shells, as well as something I could
use to cut wads to put in the 410 shells. And I plan on doing this with little to no machining
of any of the parts, and even if you go to buy the components that I'm going to use to make this
little kit, it shouldn't cost you more than ten dollars. So let's go in my little shop and see if
we can scrounge up some parts to make this little 410 reloader. To figure out what parts I'm going
to need for this build, I've got a rifle reloader, then I've got the semi-spec sheet that has both
the cartridge and the bore dimensions on it. So the first one is I've got to have a sizing die,
and because I'm going to do both brass and plastic shells, I've got to have two of those.
Then I need a primer seating tool, I need a primer removing tool, a decapping base,
and I'm going to need some type of shell holder. Now that I have my parts list, I can start digging
through my small parts containers and see what I can come up with. See what we can find in this one.
I think that bolt's going to be too big. This one may work. Let's see, and this spike may work as
well. They're good to bolt. All right, there's one container down. I believe that I've assembled
all the parts I'm going to need for this no-cost 410 reloader. Starting off with the two sizing
dies, I believe I can use this pipe nipple and a piece of half-inch PVC pipe to size the plastic
shells, particularly the brass part of the plastic shells. Then I've got like a seven-sixteenths nut
that I can drill out and use that to size my brass shells. I'm going to slide all those over there.
I've got two nine-sixteenths nuts that I believe I could drill out and use to make a shell holder.
Then I've got various bolts and a spike that I could use for my decapper, and I think that I'm
going to go with the spike and just cut it down and grind a tip on it. So I'll put those over to
the side. For my re-priming tool, I'm going to use a piece of bamboo, and I know that's kind of weird,
but I'll show you why. The primer fits in there just perfectly, and I can use the other end of
this to pack the wad into the shell, and I'm going to use a wad from a 12 gauge to act as kind of a
buffer as I hammer the primer into the shell. Now that I have my little piece of PVC pipe sanded
and starting to fit into the pipe nipple, I'm going to mark it and cut it off to the length of
the pipe nipple. I'm just going to take a file and clean it off a little bit. Then I'm going to take
and drive it into the pipe nipple. Let's see how this is going to fit. Yeah, I think that's going
to work pretty good. That's what I was hoping for by using this piece of PVC pipe and driving it
into this nipple, was that it would compress it down and give me the dimension I needed to size
the brass on a plastic shell. So there's one sizing die complete. Next I'm going to make my
second sizing die and my shell holder, and to do that I'm going to take the 7 16ths nut and I'm
going to drill through it with a 15 30 seconds drill bit. Then I'm going to take my half inch
nut, which I thought was 9 16ths, but it is half, and I'm going to drill through it with a half inch
bit about halfway through to make my shell holder. I think that's going to work pretty well as my
shell holder. Now that I have my brass shell sizing die complete, I'm just going to test one of my
brass shells in it, and as you can see that's pretty dang tight, so that's what I want.
So now I'm just going to take a file and knock some of the sharp edges off of it. Now that I have
both of my sizing dies complete, I'm going to move on to my shell decapper, and I decided to go with
this long spike, and what I'm going to do is I'm going to cut this down about four inches long,
and then I'm going to grind this down to where I have like a 1 8th diameter nipple in the center
of it. Now that I have my decapping pen ground down, I'm just going to take and file it until
it fits the flash hole in the primer pocket. When getting this decapping pen down to the
dimension where it would fit through the solid brass shells, I found that it was too small to
do a regular 209 type primer, so to remedy that situation I found a little piece of steel, and
that's what I'm going to use to actually deprime the 209 primers. So this is going to be a little
added piece to the kit. This video ran a little bit longer than I had anticipated, as they sometimes
do, so I'm going to have to split it into two parts, and I will upload the second part of
building this little kit and actually reloading the shotgun shells next week. So until then,
I'll see y'all next time. Thank y'all for watching.
