I recently bought the DeWalt® 735 13” (33 cm) planer. I have wanted one for a long time and have been saving up over the last few years. It’s a beautiful machine and is one of the most popular planers ever made. And - for good reason! With a larger capacity, 4 support posts, 3 knife head, assisted fan chip ejection system, robust construction, and easy-to-access controls, the DeWalt® 735 has become the de facto “bridge” machine between smaller “breadbox” type planers and larger stationary commercial machines.
With the accessories available for the DeWalt® 735, this machine is even better. Add the infeed and outfeed tables, stand, and even a digital thickness gauge and a helix cutter head, and WOW! In other episodes, we’ll show you the setup of the machine and we’ll put it through the paces and let you see how well it performs. We’ve also purchased a Byrd Tools Shelix cutter head, and in another video, we’ll show you the installation of the head and the difference in sound levels between the standard and helical heads.
For today, we’ll show you the unboxing and assembly of the DeWalt® DW7350 Mobile Planer Stand as well as give you the dimensions of the stand, including the space under the top that could be used to install a shop-made drawer set. We’ll also show you the installation of the planer onto the stand.
To complete the assembly of this unit, you’ll need a 13 mm open-end wrench, a 13 mm socket and ratchet, a medium crosshead screwdriver, and safety glasses. To assure you don’t scratch the pieces as you assemble them, you can place a packing blanket on your work surface. Additionally, you can use a silver marking pen to designate the top and bottom surfaces of the pieces, as we as having a mechanic’s magnetic bowl on hand to keep bolts, washers, and nuts together as you use them. There are NO spares supplied with the unit, so be careful not to lose any of the fasteners as you proceed with assembly.
The DeWalt® DW7350 mobile stand has the top pre-drilled to allow installation of 3 different DeWalt® planers: DW733, DW734, and DW735.
STAND DIMENSIONS
The dimensions of the stand are 27-¼” (69 cm) deep, 21-¼” (54 cm) wide, and 29-¼” (74 cm) tall. The wheels add a bit of width to the base, with the dimension from the outer wheel to the opposite outer wheel being 25-¼” (64 cm). The top itself is 24” (61 cm) deep by 21”(53 cm) wide.
How you install the pivot wheel assembly also affects the “footprint” of the unit. If you assemble it the way we did, the pedal doesn’t extend outside the bottom frame of the unit. This reduces the risk of a trip or a stubbed toe, but it does make it a bit more inconvenient to raise and lower the unit for rolling around or making the unit stationary. That’s because the pedal can’t be easily reached directly “head-on”, but rather from the side.
As it turned out when the stand was put to use, and a home for the tool was set in the shop, we changed the pedal to be outside the bottom frame. It is much easier to use, and it didn't turn out to be in the aisle.
Here’s another feature you may like about this mobile stand. There is a medium gauge shelf about 10” below the under edges of the top frame rails. This can be used as open storage as is or could be further utilized with a shop-made drawer or toolbox setup. The opening to place it all in is 24” (61 cm) deep, 10-½” (27 cm) high, and 14-¾” (37 cm) wide.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We finally did it.
We bought the DeWalt DW735 planer,
wanted to have this for a long time.
We'll review this another time.
Today, we're gonna talk about the planer stand
that's from DeWalt,
and we're gonna walk you through the assembly of it
and some of the critical dimensions on it.
Stay tuned.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We're excited to have this planer,
but before we get into this planer,
I really wanna talk to you about the stand that it came on.
This planer stand is designed to play well
with three of the planers that DeWalt offers,
the DW733, the 734, and the 735.
Now, the 735 is this style planer right here,
four post, has a 13-inch path through it.
The 733 and the 734 are commonly known as breadbox type.
They're the more shape with just two posts
and probably a more common planer in many, many shops,
but this stand is pre-drilled on the top
to accept all three of those planers,
and because it has an MDF top,
you could apply other planers as well,
whether it's rigid or somebody else
that's got another thickness planer.
Now, let's walk you through assembling this down below,
because it can be a little bit tricky,
but we're gonna just hit a high-speed tour
of what to expect.
So the box that it comes in, pretty straightforward,
broken down pieces inside of it.
You're just gonna unpack it,
unsleeve it out of some of the packaging here.
It all came in form foam, packed very well.
The top, which you see right here under the planer,
it was on the underside of the foam,
so at first you're going, where's the top?
But it's tucked in nicely and kept safe there,
and you're gonna pop that out.
Now, here's the tools you're gonna need to assemble this.
Number one, the instruction manual.
You'll also need a 13-millimeter open-end wrench,
a socket, and an open-end wrench that's 13-millimeter,
and a large Phillips screwdriver
for some of the fasteners you're gonna be putting in here.
So those are the tooling that you need.
A magnetic bowl is really handy too, a mechanic bowl.
So as you're in each section,
go ahead and throw your parts in that.
And then DeWalt did a really nice touch here.
Each of the part bags that go with the particular step
or sub-assembly are labeled.
So you can see that right there.
That makes it really easy to know
that you're using the right fasteners
for the right stage of assembly.
Now, you're gonna begin with the bottom rails.
And what you can see here is the bottom side.
And here is the top side.
Notice that the cutout for the upright
that will be installed shortly,
but it'll be bolted all together loosely.
Don't tighten it down at this point.
And now, next comes the wheels and the wheel brackets.
The thing to remember on the wheel bracket
is you only install one bolt at this point,
the one that's furthest away from the corner.
The reason is the second bolt will be actually used
to attach to the upright on the table itself.
So don't do the mistake I did.
Did I say that?
Don't do the thing that I heard somebody else did
of putting in the bolt and then coming back
and going, oops, I gotta take that out.
Once you've installed the wheels,
then you're gonna fasten the rubber leveling feet
on the opposite side of the frame.
And that is where the table sets
whenever you lower down the roller system.
You can now mount the pivot wheel
and you have a choice of whether
to put it inbound or outbound.
Now, I chose to put it inbound
so that it didn't encroach into the workspace
or into the work aisle.
But what I found out in practice,
I'm gonna change that even though this is set up right now
with it inbound because it's really difficult
to get your foot in there.
And if you put it out on the front area,
it's just really right, ready to step on.
And it kind of broadens the footprint of the machine a bit.
And where we're gonna place this machine in here,
about right where you're standing now,
right in this area,
it's not gonna be in a place
where I'm gonna come by and kick it.
So we're gonna go ahead and change that pedal up.
Now, it's time to install the frame uprights after that.
Notice the difference between the top and the bottom.
The top of the uprights have much more holes on it.
And you'll use the remaining hole in each wheel bracket now
to affix those uprights to the bottom frame.
And now with all the stand upright secured,
it's time to install the top frame portions.
When you do that,
you're going to align the holes properly at the top.
And notice there's little nibs on some of the parts
and detents that make those parts fit together.
Line that all up.
Now that you have all the main stand parts,
the detents and the nibs are all in the right place,
everything's aligned,
go ahead and tighten everything up.
And now it is time at that point
to put in the shelf support sides.
There's a middle shelf in the stand right here.
As you can see, I already have something sitting in here.
It's a moderate duty shelf stand.
And you can go ahead and put those side shelf supports,
then put the shelf in, tighten it in place.
Now it's time to install the stand top
with the provided bolts, lock washers, and nuts.
You're going to use a fairly sizable Phillips screwdriver
and box end wrench to secure the top,
and then take the time to align all the screw heads,
make it look nice so it wasn't just slopped together.
Now I've jotted down the stand dimensions on the top here.
You can see here that give you the width, the depth,
the height, how far off the floor it is.
And they're in the description below as well.
That's good to know so you know how high a machine
or where the path's going to be
in relation to other machines,
or perhaps to set it so that the work surface
is the same heights of others,
so you can use them as outfeed tables
or workpiece supports.
The only thing to do at this point then
is to go ahead and install the planer of your choice.
This case, as I said, the DW735.
Now there's a couple things you may want to know
just for those of you who do want to know
working surface heights.
One is the feed tables right here,
both the infeed and the outfeed.
Here's the infeed table and the outfeed table.
When it is set on the floor like this,
it's 32 and a 16 inches above finish floor,
or about 81 centimeters.
If you're looking at the height of the rest
across the top for handling stock
or resting stock back and forth,
this is 42 and a quarter inches above finish floor,
or 107 centimeters.
If you look in the description below also,
I'm going to give you some critical dimensions
of the cavity down below in here.
So if you want to build an auxiliary cabinet
or something like that, you know what size this would take,
or maybe you already have a drawer set
and you want to know if it'll fit in there.
All that'll be in there for you.
Well, if you really like this tool,
you might be an aficionado of other DeWalt tools,
like their very popular miter saw stand
and accompanying like a sliding miter saw.
Well, those are great systems that DeWalt has done,
but they all have an inherent weakness,
and that's the latching system
that affixes the saw to the rails of the stand.
We have a great solution.
Check out this video where we show you a great solution
from FixMyStand.com.
You'll fix it once, one and done.
You'll love it.
And you can do the whole refurb for under 50 bucks.
And while you're at it,
check out this other video
that YouTube thinks is perfect for your interests.
Until the next time,
this is Dirt Farmer Jay from DirtFarmerJay.com.