DIY Clay Incense Holder | Clay Lotus Flower Decor | Tea light Holder Tutorial | Polymer Clay DIY

Cute Clay DIY
9 followers
10 Video ViewsยทFeb 28, 2023
Hey guys, welcome back to my channel and to another DIY
because let's be honest, it's been a while.
And in today's video, I'm going to show you
how to make this cute lotus-inspired
DIY incense holder out of clay.
It's perfect for sticks or cones, whichever you prefer,
and it's a great room decor or gift.
Let's start with a lotus flower first.
Begin by rolling out a piece of air-drying or oven-baked clay.
Here I'm using oven-baked clay by Sculpey.
While you roll out the clay, make sure that the clay
is not too thin and not too thick
because it can get too thin in the process.
Once the clay is rolled out evenly,
take a round cookie cutter or something else that works
and cut out 11 circles.
These are going to be the petals
of our lotus flower and the base.
Here I'm using the cap of my glue stick
because I had no idea where my round-shaped cookie cutter was
but hey, this works pretty well too.
Remove the excess clay and keep it for later.
Now to create the petals, take one of the circles
and elongate it a little bit
by stretching the clay to the sides.
Do that very carefully.
You want to get a more oval-shaped piece of clay.
Next, pinch the clay at one of the ends
to create this folded edge.
If you want, you can also add some more details
by carving in thin lines across the petal.
Here I'm using the end of a paper clip because it works too.
And now you want to repeat these steps
with the other nine pieces of clay
as the last piece is going to be the base.
Next, place one petal after another all around the base
while slightly overlapping the base and the petal next to it.
For this design, I only wanted to make two layers
with five petals each.
You don't have to press anything firmly just yet.
We just want to prepare everything
and place everything to the right place.
When you place the petals for the second layer,
make sure that the petal is in between
the two petals that are below it.
I know there are different designs of a lotus flower
and it might not be the most realistic-looking lotus flower,
but I still find it looks cute and lotus-like.
Move around the petals until you're happy with the placement
and then take another small piece of clay.
Roll it into a ball and then carefully press it down
into the middle of the flower.
This is going to be not only the center of the lotus flower
but also the area where we will create the hole
for the incense stick.
Now, carefully push the middle petals towards the center
and carefully press down the area of the petals
that overlap each other.
Next, turn the flower upside down
and press down the other petals
to attach them to the layer below
while holding the flower at the center.
To secure everything even better,
you can also press in the clay
all around the base area of the flower.
This way, the clay in the center
gets attached a little better.
And this is how it looks so far.
To add more detail to the middle part,
you can take a toothpick or the end of a paper clip again
and then poke in a few holes
on top of the center of the flower.
And to make sure that the hole
for the incense holder is thick enough,
use one of your incense sticks
and press it down, holding it either straight
or slightly to the side.
It depends on the design you want for your holder.
Now it's time to create the lotus leaf
where we can put the flower on top
to hold the burned parts.
Again, start off by rolling out some clay
and this time the clay can be a little bit thinner.
While you're rolling out the clay,
you can either try to create a round shape just like that
or you can use a bowl to cut out a round shape.
Next, you want to carefully press the clay down and upwards
all around the edge to create this floaty and wavy shape.
It might take some time until you figure out
what works best for your clay
because it can be a little bit tricky.
The size of the leaf depends on the size of the lotus flower
so you can just place it on top
and see if you're happy with how it looks
and adjust the size accordingly.
If you want, you can also add some details to the leaf
by carving some lines starting from the center.
But if you want to color everything later,
these details might not be that visible in the end.
Make sure you are happy with both pieces
and check if you need to fix something
and then it's time to either let it dry
or to bake it depending on the clay you're using.
Once everything has hardened and cooled down,
you can go ahead and paint everything.
For the leaf, I mixed some green and white acrylic paint
and applied the first layer of paint.
From here, just use the darker green colored acrylic paint
to create these darker lines on top.
I would recommend painting the backside of the leaf as well
because I forgot to do that
and I didn't like the way it looked in the end.
While the leaf is drying, we can move on to the lotus flower.
Here, I mixed red and white colored acrylic paint
and applied the first layer all over the petals,
leaving out the center as we will paint it yellow later.
If you want, you can also add some more details.
For example, you can use a darker shade of pink
or even just red and then apply it
to the edges of the petals.
Or you can also apply some white paint
to the middle area of each petal
to create a more interesting design, however you like.
You don't even have to paint the lotus flower pink.
Next, I used some yellow acrylic paint
and painted the center of the flower.
And since the pink layer was still wet,
I went ahead and mixed the yellow paint
a little into the petals
to create a very subtle gradient effect from yellow to pink.
Now, let everything completely dry and we are almost done.
I would recommend glazing the clay when everything is dry,
at least with Mod Podge,
because the holder can feel a little sticky
after the paint has dried.
But here, I went straight to the next step.
Since I wanted to make it even cuter,
I decided to add some 3D water drops on top.
For this step, I'm using this 3D varnish
that will be transparent once it has dried.
And then I just applied some drops on top of the leaf
in different sizes.
You can also move the tip around
and create water drops that connect to each other
just to make it look a little bit more realistic.
If you have any other glue that dries 3D
and is also transparent, you can use it too.
I just wanted to use this varnish
because I have it for years now
and I never really used it.
Once everything is dry,
you can either glue the lotus flower or just place it on top.
And you get a cute lotus flower incense holder
with water drops on top.
Now, you can place your incense stick
inside the prepared hole or the cone on top of the leaf
and light it up.
Let me know in the comments below
what other DIYs you would like to see on this channel
so I know and can make it happen.
I hope you liked this video and found it helpful.
Give this video a thumbs up if you did.
And if you're new to this channel,
make sure to subscribe for more arts and crafts
related videos in the future.
Thank you so much for watching, guys.
Have a wonderful day and I will see you next week.
Bye.
