Polymer Clay Tutorials - How to make a flower cane

DIY Cute Things
114 followers
#PolymerClay #flowercane #DIY&Howto
Hi my name is Karen and I work for Cernit, a polymer clay manufacturer based in
Belgium distributed throughout the UK by
Clayground. In today's video I'm going to be showing
you how to create a very simple flower cane.
Okay let's make a flower cane. We're going to be making a flower cane
that looks like this one. The word cane means a two-dimensional design
inside a three-dimensional roll and this
this design goes through all the way through from end
to end. So what I've started off with is a packet and a half
of Cernit. These will create the petals and what I've done to start with is I've
cut the Cernit into five equal parts and I've
rolled them into five sausages. So I've done four
so I'm just going to show you how to do the fifth one.
So I'll just put those to one side and I'm just going to roll the fifth
petal just to show you how it's done.
So I'm just giving it a little roll and I press just making sure that there
are no air bubbles in there. If there are air bubbles in there then
the clay does just break up so you just need to do lots of little
presses. Also pushing inwards
that's a good tip for getting rid of air bubbles
and lots of little rolls. So once you have your roll there
I'm going to make sure that it's the same size
as the other rolls that I've done. So I'm just going to
place them all together and I'm going to take the blade
and I'm just going to trim the ends just so that I've got
nice sharp clean ends there and just check that they're all roughly
the same size. So now what we need to do is we need to
wrap the petals like this one. So we're going to wrap
the roll and we're going to insert a piece of
clay in the center to create the petal.
So just put that one to one side and what I've done is I've rolled through
on the number five setting on the pasta machine
some red clay and I'm going to wrap each white sausage
in the red clay. So just pop it on there
and roll one end and then just rock forwards and back
and there should be a faint line along the clay.
And that gives you a good guide if you like as to where to cut the
clay. It's not accurate but it just gives
you a rough guide. So I need to cut the clay
and just put those two edges together.
Again just lots of little rolls you don't want to do
anything quickly because you will create air bubbles in the
cane so it's all little movements when
rolling and pressing the cane. So
I've got my roll there and now I'm going to create
this line down the center of the petal and what I'm going to do is I'm going to
take the blade and I'm just going to
take the blade and make a cut down the center
but not all the way down the center just about
halfway. So then what we have is a gap there
we have a gap there ready for me to insert
a slither of clay. So I've taken a slither of clay there
from the piece that I originally rolled out to wrap the roll
so I'm just going to put that just slot it inside and then
I'm going to close the roll again giving it lots of little presses
and then just with the knife just trim off
the ends there. Do be careful you don't want to be cutting yourself.
Just remember as well when you actually start the cane and you cut
your white into five sections I forgot to say just
remember to condition the clay because the conditioning of the clay
is important. So there we have
our first petal I've made the others ready so
what we've got now is five petals all ready to arrange around
the center of the flower. So the center of the flower
is a yellow piece of clay that I've rolled into a sausage and I've cut at
So the yellow piece is the same length and the same width as the petals
so I'm going to start arranging the petals
around the yellow center so just giving them a slight press not
too much you don't want to press too much because we're going to insert
some more clay in the gaps so we need those gaps to be there.
So there's your flower and now what we're going to do is fill in
all these gaps around the flower so what I've started with is
some red just squeeze into a ball
and roll out into a thin sausage so there's lots of
rolling and stretching and pinching. If I was just to roll then
you would create air bubbles in there and it would just break
so it's lots of little rolls lots of pinching
and lots of stretching. So I need five of these again
and what I've got there is a sausage a thin sausage that I'm then
going to press along the top to create a sort of
pyramid shape if you think more if you think Toblerone
then you've got the right shape there. So I've pinched all the way along
the top I'm just going to trim off the edges
and what I'm going to do is I'm going to insert
each one into each ridge on the flower
so the pointed end goes sits nicely into the ridge like so
just give it lots of little presses all the way
around there just one more to go as you can see the flower's taking shape
now so there we have your flower
and there's just one last thing to do and that's to wrap the whole
of the cane in some more red. I thought I'd got it already prepared
but I haven't so I'm just going to very quickly
roll through the pasta machine just need to give it a little bit of a press
there so I use the number number five setting
on the pasta machine if you're using the pasta machine that is
you can use a roller but you wouldn't get the same results using a roller
as you would the pasta machine so so what I've done there is I've rolled
a piece through the pasta machine and I'm just going to wrap the whole
thing in a sheet of red clay
and I'm going to squeeze all together so there you have the cane
with everything all in its place now what we need to do
is just to bind it all together so I'm just
giving it lots and lots of little squeezes
little rolls there a little roll on the work surface
pressing down quite hard as you can see the ends all go a little bit messy
and you think that you've lost the design
by squeezing it together but once you take the knife and you cut
the end off you'll see that actually
the design is still there now I'm just going to show you very
quickly how to reduce the cane to get it really
small so I've just taken a small slice
of the cane and I'm just quickly going to press in my fingers
to reduce the cane down to a smaller size
the smaller size then can be used for beads
or buttons lots of things actually you can also put it onto
glass or wood metal so again
lots of little rolls there lots of pressing
lots of stretching and again the ends go messy and again you'll think
that the design is gone but when we take our knife
cut into the cane and the flower's still there
sometimes you will have to cut a little bit more
a bit more off to see that the flower's still there
have it and there's your flower cane
