Magical Trees in Polymer Clay Tutorial

DIY Cute Things
114 followers
#MagicalTrees #PolymerClay #DIY&Howto
Hi and welcome to Poly Originals with Fiona Abel-Smith. I have been having so much fun
with this project so I thought it was only fair if I shared it with all of you and if we had a
go at creating some of these magical little trees from polymer clay. Now I say magical
because of course you can see colour changing lights underneath but like most magic tricks
all it is is one of those multi-coloured battery tea lights but I'll show you exactly how to make
this form so we can then sit it under obviously a multi-colour changing one or just a plain white
one if you prefer but of course it has to be the battery ones no naked flames not near polymer clay.
This is a lovely fun technique and hopefully give you loads of ideas for other bits and pieces
and it's all about leaving these little gaps so that the light shows through. So let's go
through the equipment and the clay we need and then we can get started. The equipment we're
using today is fairly standard. I'm going to be using a polymer clay blade. I often refer to this
as a tissue blade. Now for once for what we're doing today you can use an alternative so a very
sharp blade or a sharp craft knife will work. You won't get quite the same precise finish but the
blurred finish you'll get as you cut down through the slices won't be too bad and is certainly usable
for what we're doing today. So I will also be using a craft knife, a small polymer clay roller,
any roller will do as long as it doesn't react to polymer clay. I'm using a cable needle that's
about four millimetre size any similar tool will do. For the star on top of the tree I've just used
a little star cutter. For adding the layers of clay I've just got a little bit of liquid polymer
clay which I've just decanted into a pot. If you don't have liquid polymer clay for what we're
doing today PVA glue would work as an alternative. We're going to create a form to put our tree onto
now I've gone for quite a small one but obviously you can go for whatever size you like
from teeny tiny to larger ones but obviously if they're very small remember if you're going to
put lights in they still need big enough to be able to put the tea light inside. To make life
easy for what we're doing today I'm making a size that fits nice and easily on an A4 sheet of card
and I'm using these round templates from these staggered stencil shapes and I'll put a link to
where these are from from Polymer Clay UK in the details below the video. So I'm using the largest
of the round ones and the next size in of course if you don't have any of these then something like
a compass or a round bowl will also work and because I'm really enjoying making the trees
I'm going to do the complete circle which will give me enough forms to make two forms to make
two trees but if you didn't want to do that you can just make a semi-circle and obviously you can
then get much larger ones if you just use a semi-circle on the side of the A4 but see how
I do mine and then decide the size and shape you want to do. So I need one piece of card
and then we've also got a sheet of A4 paper and once we've got our circles we're going to
use a pencil to draw around, scissors to cut out and then just some clear sticky tape to make our
cones. We'll need a cocktail stick and when I'm measuring the size of the canes or the size of
the branches we're going to put around the tree I use a measuring sheet just to make it easy. You
don't need it but if you do want one this one is freely downloadable from www.printablepaper.net.
I've laminated this one so I can work on it multiple times and I use the four squares to
an inch but you can of course get it in centimetres if you prefer. When I bake I bake on a small tile
and I will tent the whole thing in some aluminium foil and I'll also give you a little bit of a tip
as to how I do this without making any mess of my polymer clay creations and so what I'm doing I
just have a few strips of ordinary cards just cut offs from other things other projects that
you've been doing. The added sparkle to our project comes from a piece of silver leaf this
is just a single square sheet and that's enough for the project we're doing. Obviously you can
get different colours and different formats I use gold quite a lot and you can actually get some
coloured leaf sheets as well which work just as well. If you don't have any of these then you can
you could add silver mica powders or you could add some glitter instead or you can of course
just paint the sides of all little branches afterwards if you want to either with something
like gilders paste or with acrylic paint so just use whatever you have to hand. I work on a large
ceramic tile I have biodegradable wet wipes and tissues that I use to keep my equipment and hands
clean as I go along wet cloths would work well as an alternative and I do use a pasta machine
dedicated to polymer clay use. If you don't have a pasta machine then you can stack layers of
playing cards either side of your clay and simply roll over the top to give you the thin sheets and
I also take you through later on what you can do as a shortcut if you don't want to do the blend
that I do and again if you don't have a pasta machine it's another quick and simple way to do
this project without one. So I think I've covered all the equipment we'll go quickly through the
clay we need and then we can start on the fun project. For today's project I'm using Fimo Soft
for the coloured parts and Primo Sculpey for the translucent clay but all well-known and
recognised brands of polymer clay will work well with this technique. So for the amounts I've got
enough here that will make certainly one tree possibly even two trees depending on how thick
you cut your slices and with the translucent the same this is way more than we need for one tree
but it's easier to have a nice large sheet it makes it easier than having to patch lots of
small pieces. So for the colours we've got Emerald Green, Peppermint, Aqua, White and Silver and as
I mentioned the translucent. So we've got half an ounce of these three which is 14 grams, a quarter
an ounce of that one which is seven grams and an eighth of an ounce or three and a half grams of
this one and this one's roughly double the size of this so about an ounce or 28 grams but I say
that's more than you need. So the first thing I'm going to do is condition all the polymer clay.
If you're unused to working with polymer clay and aren't sure about conditioning it I will put a
link to a video with some hints and tips and techniques on doing that. I use the pasta machine
to help me condition the clay and these four I will put through on setting number three to give
and on my pasta machine 0 is thick and 9 is thin. This small piece I'll probably condition by hand
I'm just going to roll it into a round blob and this piece I'm going to condition thoroughly in
a clean pasta machine so I don't get too much dirt on it. Do it on setting three as I do with these
and then I'll put this through on my second thinnest setting so setting number eight
give myself a lovely long thin sheet because that acts as the underneath piece of our tree
and allows the light to show through. So I'll get all that done and I'll bring you back and
we'll start on creating our form creating our cone and doing our base layer of the translucent.
The first thing we're going to do is to make ourselves a form for our tree to sit on and I've
done this incredibly simply by a piece of card and a piece of paper. Now as I mentioned before I happen
to have these staggered stencil shapes from polymer clay UK so I don't even need to get my
compass out I can just use these. If you don't have something like this use a compass or a bowl
but you want three sizes so I'm going to go around the outside of this one on the card which is the
larger of my shapes and if you're using a compass you can just do a half circle but because I've
got these shapes and because I like making lots of these I'm doing a circle and then I will make
two forms out of this one piece so say the card is the large shape and then on the paper I'm going
to do two lines on the smaller shape. I'll move him down this end to save our paper and I've done this
several times using different ways of doing it and this gives the easiest way to actually hold
on to your piece whilst you're working and that's what I've discovered doing three lines. So I'm
going to cut out the circle on this one and cut out the larger circle on this one and I'll bring you back
when I've got that done and having got our two pieces all we need to do is fold them in half
and chop down the center of both because you only need a semicircle to make the cone shapes that
we're using so say if you've got a compass that you're using rather than one of those shapes or
a bowl or something then simply do a semicircle instead. To make the cones first thing it's easiest
to do is just to give yourself a little center mark so you know where the top of your cone will
be and then just very simply curl the card slightly, curl it round to make whatever shape you want your
tree to be. So I think that's quite a good shape so I will just secure that in place with a piece
of tape and then I'm going to do exactly the same with our paper piece just fit it over the top
curl it round and you want to do it so that the lines match up. I'm just going to secure it in
place check that it still fits nicely round and as long as it does I will tape over the join.
Now the polymer clay doesn't stick to the tape and the reason we've put the paper piece inside
is that you'll find that the polymer clay sticks a little bit to the paper-ish but with a paper
insert once we've baked it we can easily take the paper off and pull this away from the inside
of the cone whereas with the cardboard one it's much harder to do. It also means you can reuse
this several times and the other thing I've learned through doing this multiple times
is that I make the paper cone slightly larger than I want the tree itself to be because this
gives me a place to constantly hold as I'm working with the tree so I don't have to touch
any of the tree itself so you don't get any fingerprints on it but that will become clear
when we move on to the next stage. So there we go our form is all ready to go so the next thing
we're going to do is we're going to add our translucent layer as a base and bake that.
I conditioned the translucent clay through a medium setting on my pasta machine as normal
and then I've put it through my second thinnest setting so if you're rolling this out by hand
it's probably only about one possibly two playing card thicknesses. Now this is the only slightly
tricky bit of the whole thing but what I would say is don't panic you don't see this bit it
doesn't have to be particularly neat and the way I've started to do it is I just lay the clay
over the cone but I've put it so it's right up at the top. You'll normally get a piece that
overlaps underneath and with my fingers I'm just flipping that underneath and holding on to it
because that means that the clay will stay nicely around whilst you sort yourself out.
So we only need to go down to the pencil line so when I've got it to stage where I've got the
rough edge I'm just going to neaten it off slightly and making sure I've still got that
bit tucked under you should be able to hopefully fold the clay around so it sits nice and snugly
against the paper and just overlap slightly. You can generally feel where the overlap is
so just cut through slightly wider try and only go through one layer obviously minding your fingers
at the bottom but if you do go through both do not worry because I have there that's absolutely
fine because just piece it back together and whether you've cut through both or not we are
going to roll across the join so that the layers go together and having the card underneath gives
you the strength because obviously I've got my fingers on the inside to give yourself a nice
firm base on which to actually roll that over. Don't worry if you've got a couple of layers
overlapping and if your piece isn't big enough to go all the way down but as I mentioned this
is why I gave us a nice big piece so that hopefully all of you can actually get it on first time but
you can simply cut off a bit and paste any scrap ends in that you need. So all we're going to do
now is just cut off neatly all the way around where we see the pencil line again watching your
fingers if you're using one of the blades. So there we go that's our base done and that is the
most complicated part of the whole piece so if you're with me so far the rest is going to be
such a doddle. I'm just going to show you one other thing I do at this stage just which might
be a little bit of a tip for when you're baking things and baking tall things when we get our
finished tree we're going to have a star on the top and normally as you know when I say to bake
or to cue your polymer clay I recommend covering the whole piece tenting it in aluminium foil.
Now if you've got something very delicate on the top like a little star then obviously if you
tent the foil over the tendencies for the foil to go down and it might tip onto the star and pull
or push it down so what I do is this so I've got my tile and I've put some pieces of card
on the bottom and I have made a cage so that now any of my pieces can sit nicely inside the cage
and I can tent over the whole of this with aluminium foil and nothing inside is touching
the foil and it will all bake safely so that's our cane base done so let's now start on the leaves
and the branches for the tree so we're going to make the decorative branches now that go around
the tree and I'm going to do something called a skinner blend with the white the aqua the
peppermint and the emerald green however if you don't have a pasta machine or if you're not really
sure about working with polymer clay you could simply roll this up into a sausage then wrap a
layer of that around the outside then a layer of that and then a layer of the white and you'll get
roughly the same effect that we're going to do but I know most of you work with polymer clay so we're
going to do a skinner blend if you're unsure about skinner blends at all I do have a tutorial
with some information about them and I'll put a link to that in the video below but other than
that normal process for a very simple skinner blend diagonally through the end pieces so that
when you put these pieces across we've got that diagonal give them a slight roll
and I'm going to fold them and put fold first through the pasta machine and keep folding bottom
to top bottom to top until I've got a nice blend from one side to the other and you'll notice I've
got less of the green of the dark green that's because it's quite a strong color and if I had
the same amount then I'd have an awful lot of the green and not so much of the sort of more
wintry tones which is what I was doing for today and of course because I've got four layers of
clay now I will put it through on one thicker setting of my pasta machine which in my case
is setting number two so there we go a lovely blend and it gives that sort of wintry feel
of the snow on top of the evergreen branches so chop it into two or three pieces depending on the
width of clay sheet you've got layer them up press them together so they're not going to move
as it goes through the pasta machine pinch the dark end I'm going to put back through on that
same setting number two on my pasta machine to give myself a longer strip of clay and now I'm
going to go down to my thinnest usable setting which on my pasta machine is setting number nine
but if you know that your pasta machine shreds or tears your clay just go down one setting at a time
till you get to your thinnest usable setting so there we go so I'm going to start rolling this up
from the dark end first and when I'm rolling I'm just trying to make sure there's no air trapped
I'm not worried about it being untidy at this end because we're about to change the shape of it
so you've ended up with a lovely plug of polymer clay with the dark on the inside and the white on
the outside I'm not worried about it being messy on either end and all we're going to do now is
cut this down into quarters so if you'd done it without using the pasta machine so you only
had to wrap the colors around each other you should also have ended up with a round of clay
about that sort of same shape and size so you can follow along from this point onwards so I'm going
to chop down you don't need to worry if the quarters aren't exact because this is a natural
thing so it doesn't matter if one end of our cane is different from the other and one at a time I'm
going to take these sides and just pull them up round and slightly up the side and then with the
bottom we're just going to press in along the bottom to create a thinner shape I'm going to
do the same with the second one put the two together same with the third and fourth and
then put all four together so I'm just pressing in at the bottoms having just pressed in at the
bottoms I'm going to press in along the side of my thumb whilst at the same time keeping some
fingers on the end so sort of trying to neaten off and flatten off the end turn over and do the
same on the other side and that stops these two ends sticking out too much and now I'm just pulling
over right at the top and then we can cut down halfway through put the two pieces together
so I'm going to push them together like this so you can see I'm creating a sort of a diamond shape
to do it one side and then the other and then work down the middle press in again to end up
with something that's more like a square shape so you can see here again do the same top and bottom
and now we should be able to turn it on its side and press down and reduce this in a square shape
and by reducing all I'm doing is I'm pressing in whilst moving along the length of our cane
and slowly and gradually that will make it longer if you find your corners pull back just stand it
flat on your surface and actually physically pull the corners down and because we flattened those
ends off when we were putting them together we should still end up with a fairly nice flat ended
cane and I'm going to reduce this down in this way until across this length we've got about
just under three quarters of an inch probably around sort of two centimeters
so I'll carry on doing that and we'll stop when I've got to that stage
okay so it's actually just slightly less than three quarters of an inch and I've got probably
one two three four five it's about five inches twelve and a half centimeters I'm just going to
take off one piece that's about two inches about five centimeters long and these will be our largest
bottom branches and all I'm going to do is I'm going to change the shape so along the edge
I'm just going to push in to blunt it slightly and I also want them fairly slightly smaller
so with my thumb and my fingers I'm going to push inwards so as you work the way down the cane
push inwards and that gives you a slightly narrower shape it'll also make it slightly
more diamond and again we will just blunt off the edges slightly but we do want a roughly
diamondy type shaped branch because that's going to create the gaps where they join at
the top where the light's going to shine through so when you think you're ready have a chop down
through so something along that sort of line and that is probably just over about three quarters
of an inch about two centimeters but obviously this is just for those of you who like the guide
to sizes you can do whatever size you like what I am going to do however is to neaten off
and chop off any of the wastage on that end and check that I've roughly got the same size on that
end which I have that can go to one side so that's our first piece done so I'm going to continue
reducing this down until it's about half an inch or about just over one centimeter 1.25 centimeters
in width and again I've got one two three four five roughly sort of about five inches twelve
and a half centimeters I'm going to chop off probably about half of it and again we're just
going to change that shape by blunting off the sides and again just pushing in refining it
slightly without pushing in motion with our hands blunt off the sides and you're looking for a piece
that's noticeably smaller than our first piece I'm just going to even off either end make sure
both ends are the same as you can see there that one's quite a lot wider still so I'm just going
to press that one down and pull it out so it ends up being sort of more of the size and now it's
better so that's my second size and then the last one smaller still so again sort of under the size
we're going obviously but I will normally do this probably to the length is what I look at more than
a size so probably till we get it to about three inches seven and a half centimeters not counting
any of the wastage on the end so you have a fair bit by now on this end so take that off
and then we'll press that in as before and again go down the length let's see how we're doing
compared to the medium size so again so if you take three sizes so that sort of thing we're
and that's the sort of sizes they came out to on the measuring sheet if those of you
who want to sort of put it through so that one was sort of just under an inch that one's about
three quarters that was just over a half and obviously the relevant sizes in centimeters
instead the other thing I will do at this stage is to get my silver clay make sure that's nicely
conditioned get it nice and soft roll it in your hand I'm going to press it flattish and then give
it a bit of a roll I want it quite nice and chunky but big enough that our star will fit onto it with
a star cutter because we're about to get the silver leaf out so I would also recommend you
have something like a biodegradable wet wipe or a wet cloth handy as well because the silver leaf
does go everywhere okay so there's my silver leaf and what I'm going to do is I'm going to
where the darker end is set that on one outer bit of the silver leaf same let's do him it's a shame
I've got that bit missing there not to worry let's do him at that end shove that on there for a minute
and him on this side and I am going to roll them so do this one first because I want as
complete a covering as you can get on the three canes we also need to do the same with the silver
so any bits that stick to my finger I'm going to do that bottom of the star and then just spend
a bit of time making sure you've got as much coverage as you can patch any bits where it's
missing and if you don't have any silver leaf then this is the stage at which you would put on
the glitter or the mica powder instead and the same thing you'd wrap as much around to get a
covering as you can all the way around the sides of the canes and the reason we made the cane the
size we wanted and then added the leaf is because as you stretch this out so all of this will crack
on and you won't get as lovely neat a finish on the side of your canes but doing it at this stage
we should get good coverage certainly for our first couple of layers around our tree
when your canes are done you can turn your attention to the star and I'm just going to
cut through I've got the silver on both sides so with my cutter pressed down I'm not worried
that it will generally stick into the cutter because I will use the cable needle to gently
pry it out because we're going to change the shape so I'm just prying it out by the points
because we change the shape slightly anyway and we are also going to add any extra bits of
the silver leaf that we can down the edges of the star and you see what I mean about getting messy
take your time take the excess off once you've got it all around the
sides of the star I'm just going to make these points slightly more pointy
than a flat and then with a cocktail stick I'm going to go in the bottom edge of one piece
press it in a fair bit and then give a good wiggle so that I create a nice round opening
at the bottom that we can sit the top of our tree into later so the next thing to do is
clear up any mess and then we can start adding the branches onto our tree if you're lucky by
now your cone will have finished baking and be nice and cold mine hasn't but luckily here's one
I made earlier so first thing to do is just very gently just go inside so I'm just bending the
paper away very gently and just releasing it from the underneath cone because you want to do it at
this stage because you're not going to press down on it once we've got all that ornate decoration
around the outside so once it's released you know it's all going to be fine pop it back on
and then with a little bit of liquid clay or if you haven't got liquid clay then pva glue would
actually work just as well just for the bit we're doing at the moment I'm going to put on
some liquid clay just so that the branches when we cut them off and add them in will have something
to adhere to so it's not a huge amount but it's sort of enough that it'll be nice and sticky and
tacky and with pva glue if you use that instead you don't necessarily have to wait for it to dry
you can put it on whilst it's still wet because like the liquid clay it then gives you then a bit
of maneuverability but it just adds an extra something and allows the branches to stick on
and move around more easily so we can have fun and position them okay here we go so find your large
cane now the other thing with this is I've given you enough clay here with the proportions we've
got and the size of our tree that you can really sort of take some nice chunky leaf branches if
you want if like me you've got a lot of silver on the end you can always just take off one end
just to give you an open up thing and what I tend to do because we've got a diamond shape
I will sit it so that only that pit is on the tile and I'll be supporting the rest in my hand
making sure obviously I don't get the blade anywhere near my hand and then I will just
take whilst it's still upright take slices and move along and I've learned from experience that
probably about 16 slices is a good place to start when you're doing the bottom round of your tree
and certainly for the bottom slices something about that thickness is a good slice to go so
it's a good probably sort of three millimeters probably about 16th of an inch or something like
that just for the bottom and then as we go up higher they can become thinner if you like but
it's good to have nice sturdy ones just at the bottom so I'll get 16 of those cut and bring you
back when I've got that done and this is why I've got the piece of paper here so you can hold onto
the paper and know that you're not touching the cone in any way and these bottom ones go so that
the top half sits on the cone and the bottom half comes off the bottom and at the moment I'm just
placing them on and I'm not pushing them down too much because that'll give us a chance to then
move them around a bit if they don't fit on if 16 don't happen to fit on exactly
so just work your way slowly around the bottom okay so for me that's number 15 but I've got a
little bit of a gap so what I'm going to do is I'm just going to pull or push just the edges
of my bottom three pieces or the three pieces next to each other just slightly wider and then
they should just about fit on if it being the other way around and to be honest it normally
is with me that I have a bigger gap but not quite enough to fit a piece in then I'll take
three pieces and just push them just inward slightly to make them narrower so then the three
fit on but once we have all our pieces sat on nicely then again just holding on to the paper
you can very gently just roll just the top part oh it's fallen off already just the top part
just to secure them nicely in place he really doesn't want to go on does he there we go
okay so that is our first layer done now as I said at the beginning I'm using Fimo Soft
now I know I can go the whole length up this tree and then pull them out and curl them out
the branches up afterwards if your clay is very sticky then as we go around each layer I would
suggest you curl them at that time so I want to get another couple of um rows out of this one
so what I'm going to do is I'm going to push it very slightly inwards again and then blunt off
those sides so I've got a slightly smaller piece than the one I just had and again we now know 15
slices so I'll do 15 slices and put them around the outside and then repeat the same again to
make this slightly smaller to do the third row up and we should hopefully have enough to do all
three rows from this one cane so the next row sit so that this one goes just in between the two pieces
and again just work your way around I put them just on gently to start with to make sure
I don't need to make any adjustments and then when I finish the whole row
I will go along with the cable needle and push them in more firmly just on that top
and then as I said I will repeat and do the same with row number three so now it's time to move on
to the medium size and with any luck your large one should still be slightly larger than the
size and then we're going to do exactly the same so I normally do three levels of this so start one
and then same as we did before press down reduce slightly add the next layer and the next layer
and then the final layers will be done with the smaller cane and remember what I said about the
checking whether your pieces are sticking because I know I can pull mine up nice and easily because
it's Fimo soft but just check at this stage and see whether yours are sticking at all so I will
add the next three layers and bring you back when we move on to the smaller one when you get to the
upper stages you might well find that you don't go right above each one but you sort of start to
fill in so you won't have 15 for instance pieces around the outside it'll be slightly less that's
fine just fit them in where you need to but just be aware you still need to have little glimpses
of the translucent that will show when the leaves curl up so we get that nice light effect coming
from the underneath and then the last few layers will be doing the smallest cane and then we'll
just add as many as you need going around until we end with a nice bit on the top and the very
top layer tends to be either three or five just to get a nice uneven number for the very top part
of our tree for the very top layer just very gently pull the pieces together with your fingers
just to create a nice point at the top of your tree I must admit I love the way it looks when
you look down at it from the top so now we get the exciting bit of curling up the leaves if it's
something you haven't done already I tend to pull them slightly up with the blunt side of my craft
knife and then do the rest with my finger whilst again holding onto the paper at the bottom so
pull up and curl and what I'm looking at is I'm looking at seeing a little bit of translucent
showing through the underneath because of course wherever the translucent shows
that's where the light will show so just work your way down and around slowly pulling up
and curling the branches and when you get to the bottom these bottom ones are going to curl up
so right up next to that translucent clay bit and what I'm looking for centred it there so you
actually see it is that you can see the translucent areas but not if possible the
tops of the branches that we've gone and then I'll just carry on repeating that and finish
around the whole of the piece so when you've been around the whole place and checked that you're
happy with all the placings have another little look just at the very tip of the tree I have a
terrible tendency to be holding on to that whilst I'm pulling them up so sometimes I flatten that
down but you'll really see how that silver leaf now has started to come into its own now that
we've pulled out the sides of the branches so the only thing left to do a little tiny bit of liquid
clay or again PVA glue if you've got some right on the very top of the tree and then we can take
the star we made earlier with the hole and that should hopefully just sit down on top of the tree
so that can be now baked in the tile that I showed you before where I've created that
cage of cardboard and then going to tent as before make sure the whole thing's tented in
aluminium foil and bake according to the manufacturer's instructions for the brand
of clay you are using so here's our little tree all baked and all cooled and all I've done of
course because you've got that lovely hollow form is just sit it over a little multicolour changing
tea light now of course please be safety conscious the only ever used battery tea lights never use
the naked flame ones not with polymer clay or burn but little battery ones sit over and give
that lovely magical changing light effect and I can now add him to our little polymer clay magical
tree forest I will add all the colours for the other trees in the background in the details below
well that's it that's our magical trees in polymer clay project all finished and now it's just a case
of having fun experimenting and making some of your own but remember just leave some of that
translucent clay showing on the underneath and then you can have colour changing little festive
trees thank you so much for watching as always a special thank you to those of you who subscribe
I really do appreciate it I think I might need a few more trees for my forest so guess what I'm
going to do hopefully I'll see you next time bye for now bye
