Can we Fit in our Carriage Kart's TINY 7 Sq Ft Cab? Twin Engine Power Wheels Go Kart Build Pt. 1fbra

Automobile Regency
59 followers
16 Video Views·Oct 25, 2022
Welcome back to our Cinderella's twin engine princess carriage build. This
thing is gonna be an off-road beast with about 30 to 35 horsepower when we're
finished up, but we have a problem. Look how long it is. Right now it's sitting at
about 20 inches longer wheelbase wise than what we're building it off of, which
is a Manco Dingo. So this thing needs to get much, much shorter. So in today's
episode we're gonna be addressing that. We're gonna build mounts for the seat
and optimize the seat position. We're going to figure out where our engines
are going to sit, and then we're gonna build a dashboard and build out our
door bars up to a roll hoop in the back. It's gonna be challenging. It's been good
so far, but again our goals are lightweight, good power to weight ratio,
durability, and suspension. So let's get started. So first off I'm gonna start
with some seat mounts because I mean it's kind of hard to get some
measurements for the rest of the cage and dashboard. So and then we'll move on
to fitment of the engines because the clearance is gonna be back here behind
the seat. So let's get started. Chop top. It's a roadster now. Made some tweaks to get the seat
fastened down a little bit better than it was. So we need to square up the egg
basically the bottom half and we're gonna shorten this a little bit of
course it won't line up just quite right for the video right now, but we're gonna
be needing to make some plunge cuts here so that way it can realign back up with
we're gonna add a couple of oh yeah that's right probably a brace right here
and then a dashboard of some kind right here and we're gonna get rid of this all
together and go from there dude. Because we're building this thing on a
floor in a shop that's 50 years old we have no jig. So basically we have a
little red dot over there that's where we're drilling our hole. Yeah so do the
math. Basically we're just hoping that that's gonna work and we're gonna have
to put a little bit of abandon this in order for it to meet the frame where we
need it to. So hit it buddy.
Thanks granddad. Yeah you need to waller that thing out man. I'd hog it out a little bit.
Still causing some angle problems. Just like that Project Princess was
abandoned for almost an entire year and here's why. We designed this go-kart for
a collaboration race at Redbeard's garage property that was canceled. Our
plan was to surprise the competition with this full suspension, lightweight
and powerful go-kart that would both dominate and embarrass the competition.
The race was never rescheduled so the project sat. We finally have a nice big
new shop to work in off the floor and I'm really excited about getting this
project done. I think we need to pick up at seating position and rear axle but
let's go see what kind of damage we got bring it in here see how much work we
have ahead of us. We just got so busy with the new shop and other projects
this got forgotten but I can't wait to get it get it going because it's gonna
be the ultimate troll machine dude it's it's gonna be passing people at three
and at the tea party at five you know. Oh boy. He said it. So let's grab it let's be
careful it's only barely packed together. You got it? Yep. This is cool man we've
never had like an abandoned project that was never this far along. Yeah we
were thinking somewhere like around here we're not sure where the engine plates
and stuff are gonna be but yeah definitely not we're not not another
limo. I like long beds though man. You're a long bed guy or you're not. Now that we
have the go-kart on the table in the shop our goals for today's episode is
just to get caught up on this thing look everything over and finally get our
clamshell body mounted so we can have a good visual by the end of today's
episode so a lot of test sitting is gonna need to be done but let's get
right into it. We trimmed so much of this away. Okay we have a hole drilled there I
think that's where this tube goes. Yep. Right and we never drilled one there.
See the thing is they're watching this in order but we're working on this
Apologies in advance. So this is one of those moments of trim test fit trim test
fit weld trim test fit so we're gonna get to work yeah hey we're gonna get to
work. Ever since we started this project we've had a really hard time fitting the
bottom half with the top half of our kind of clamshell body so Charles is
making a couple of brackets that we're gonna be able to bolt the top to the
bottom and so I took a Dremel and ran it in here so it'll slide through there
two bolts there and then two bolts holding the bottom on. These are the
brackets that got cut. We're gonna slip them in here and probably just run a
couple of screws in here and then just wherever they land go ahead and run them
in the bottom here. And we'll be able to flip these around where it's just the
heads and I think it'll it might look kind of cool.
So the front's gonna be a little bit trickier to come up with our mounts to
keep this rigid for fitting but we do have a crossmember that was factory with
the the power wheels. We might incorporate this somehow. I want to say
we're gonna replace it with something a lot stronger that we can mount our
steering on. Absolutely. Which we're definitely gonna need to do. But we can copy this exact
piece with some thicker metal and be happier with it. I know, don't make fun of me.
I don't think it's Huey's making fun of me. Oh. Just saying that looks scary. Huey's looks scary.
Looks bad. Looks bad. Won't be annoying. No. What's annoying about this? No.
It's just it's a bump in the road.
Don't lean back too much. Alright, just 10%. Okay. And we're doing this
because that's that's where the maximum amount of your headroom is gonna be for
helmets and mounting. Oh. You actually have an ish. That's not bad. I mean you can rep.
That's not bad. We thought we were happy with where the body was but when we all
got back from lunch and looked at it we just all decided it has to move forward.
So it looks more like it was meant to be together. Right now it just looks like
half of a frame with the body jammed on it. We want it to look like more of a
cohesive project. So we're gonna make a couple of trims right here to our body
and try to scoot the whole thing forward. Make the body kind of tuck
around the chassis here. Hopefully it'll all work out. We only have a couple cuts
left. We made some trims of the body and it's getting closer and closer but we
have these doors here and it really completes the look. But. But. It tells us
that our body is not quite as round as it once was. So we might make a few more
trims here and there. This also just could. It could be because it sat outside
for six, seven, eight months in the heat and the cold and just got this form. But I'm
gonna try to sit in here again. Oh that's not horrible. Look. Oh. Okay. We just need to screw in that back corner. We might just. We
didn't. This might be a convertible top because getting in and out is gonna be
truly a chore. This isn't bad man. We just need to. We're gonna kind of create our
own door bars and I think one is gonna have to swing open. That's the plan.
What'd you lose? I think the blocks. Yep. The blocks are gone. What we do know about this
frame is that. Well we can level it to the table. We know the table is pretty
darn level. Is this level? I mean it's within spec so we're good. And that's about the only
measurement we can use. And the other thing we're looking at right here is. See
where I marked center? Right there on the chassis. I marked center up there on the
chassis. The center line. And then you can see the top of the heart. Okay so we got to trim it or something. That would make a lot of sense. So it's an
eighth taller on your side? Okay that would then move the top of the heart over quite a bit. So we got the body to where we're happy enough with it for now. We can still make adjustments
because I mean basically the first time we send it really good the body's probably not
gonna be perfectly straight again. So we got Charles in here and he's one of the
taller people that's gonna be riding this. And we're coming up with a cross member
for our steering. And on the OG cross cart the steering cross member is really
close to Ike's knees and he bashes his knees and that's just not something we
want to deal with again. So we're gonna be putting some bends in it that aren't
kinked like that. But a couple bends in our tube. Maybe you're rocking it out like
this and welding our steering underneath that. Yeah it's really close to your knee.
I mean it looks like you have clearance now but you got to remember when you get
to bouncing in this thing. Yeah when my butt comes up my knee goes directly that way.
Yeah exactly. So rocking it forward and coming up wouldn't be a bad idea. Even
though it's gonna compromise the look a little bit. That might be what we have to do.
Ready? Yep. 30 degrees.
Like plus two. Yeah plus two. Plus two degrees for spring back. Yep.
Spring back. Yeah that was closer. Here we go. Quick twist. Hey that looks good.
All right so we've started working on I guess what we could call the dashboard.
We got the pieces notched. It's not perfect. Had to do it by hand but it should be good.
I've got it level and evenly spaced from here to here. So I'm gonna give it a
tack on both sides and maybe we can have the steering wheel hanging today.
Cover. Now that that's tacked in I'm gonna go get a piece of round tubing to
fit over this. That way it can work as a collar. We'll weld the tubing on the
bottom of the crossmember we just tacked in and the steering wheel will be hung.
So we'll tack this. Tack that little collar on there. On this crossmember.
All right cover. Oh boy. It's teetering. What was it? You got the dance at noon but the race at five?
Yep. We're gonna need to space those rears out a bit because right now our front is
wider. Go to the edge of the table. Yep. Let's just. It still could probably go
wider in the rear. I think it could. So today's episode we finalized the front
end. Got everything welded up and well took this project from being sitting in
the yard to actually working on it making progress again and I'm totally
reinvigorated. I love how it's turning out. It's definitely tight up in the
front end but we are always trying to keep the packaging small because the
smaller it is the lighter it is the more nimble it is the faster it's gonna be.
The most important thing is we have knee clearance here so no one should be
bashing their knees. That's good. We definitely need triangulation support up
here. We're gonna add that later on after we finalize the rear
suspension. Now the rear suspension and engine placement is its own can of worms
but we're gonna handle that in the next episode so leave a thumbs up if you're
enjoying this build everybody. Subscribe to Cars and Cameras. Don't miss the first
ride. Let me know down in the comments one single big block engine possibly our
turbocharged big block engine or two small blocks hooked together. I would
love to see the two small blocks hooked together. That'd be very cool. Anyway all
that next time thank you all for watching. Pick up one of our new Vote for
Turbo t-shirts on our website Cars-Cameras.com to help support the
channel and our future builds. We'll see you next time.
