Will Our FREE Abandoned Airplane Finally Start? Ep4

Automobile Regency
59 followers
Today on Rebuild Rescue we get done a lot of work to be able to finally get this engine started! After a long night of completely taking apart and cleaning the fuel system, we finally get fuel running into the engine.
Once we are able to get the fuel injectors and lines reinstalled, we roll the Cessna 401 outside to see if the work completed so far will be enough to get this engine to finally turn over after over 15 years!
Contact info
[email protected]
[email protected]
#FreePlane #AbandonedPlane #RebuildRescue
Welcome back to Rebuild Rescue.
So I've been up all night.
I was just floored by what's going on.
I mean, I can't believe this guy's trying
to like steal us out from underneath us.
Honestly, I'm like pretty emotional about it
because we have so much invested in the project
and you know, you guys,
there's just been so many good ideas.
So, you know, I feel like this is just as much
your airplane as it is my airplane.
And I don't like giving up.
Nobody's going to take this from us.
We're going to get it running.
So I was up all night.
I completely pulled the whole fuel system apart.
I didn't film it just because I just had to get it done.
So I pulled the whole fuel system apart,
cleaned everything out, rebuilt the mechanical pump.
I mean, I'm exhausted.
Like I need, I really need a cup of coffee right now.
So I got the injectors all cleaned out as well.
Put them in the ultrasonic.
They look brand new.
I'm going to get those installed yet.
I'm going to see if we got fuel flow.
I think we do.
After that, we're going to get the injectors installed
and unlock the turbo, hopefully.
Then we're pulling this thing outside
and it's going to start.
Because I mean, we do have a contract for this thing.
It does specify in the contract that it has to start.
And beyond that, like I gave the old owner my word
that we were going to get this started.
So it's going to happen.
And I'll tell you, I mean, if it doesn't start on its own,
which was my plan this whole time,
I mean, I could stick a line down in the car
with a weed spray with gas in it if I had to.
And I think that would get it started.
Or throw a propane line in there
and turn a propane tank on, something.
If I got to stand outside and spray ether in this
while this thing's turning over, it's going to start.
But I wanted it to start on its own power, normally,
with gas, that was my goal.
And that's what I said I'd do.
So let's get that done.
After pulling that fuel system apart,
a lot of the O-rings just fell out.
So I got a couple sets of O-rings.
We'll get these installed,
and hopefully it keeps fuel from leaking all over the place.
I didn't check and see if fuel doesn't,
it wasn't coming out of the injector feed lines.
I'm going to go ahead and hook the power up.
And if you guys can watch these cups,
from what I understand,
it should fill one of these cups up in 10 seconds or so.
So I'm going to go in the airplane.
I'm going to turn the fuel system on.
These things better fill up.
I don't know if you guys realize
how many fuel lines are running through this airplane.
Literally, it was all night.
Every single one of these lines here,
all of these lines here, they were all off.
They were all cleaned out.
All these lines, the mechanical pump back here.
I mean, that was pulled out.
That was cleaned out.
I replaced some O-rings in it.
I traced everything all the way back to the main tank.
I blew all those out.
It was a ton of work.
So hoping, as long as we get fuel coming out
of these lines in these cups,
I know the injectors are clean.
That's all we needed.
We got spark.
We definitely got plenty of air.
All we need is that fuel.
Let's give it some power.
Let's turn on the aux pump here.
See if we got, see if we got any fuel.
I can hear the pump running.
Give it some throttle so the fuel comes out.
Hey, we got fuel.
Oh my gosh, we got fuel.
And not only do we have fuel, it's all even.
It's the same flow, the same amount of fuel in the cups.
Not only will this start, this will run.
This will actually run.
This is so awesome.
All right, so let's get these, let's get the injectors in.
Let's get these hooked up
and we're going to pull this thing outside
and we're going to start it up.
Sweet.
If you think about fuel-wise,
that's a lot of fuel for a couple seconds of a pump.
Yeah, that's probably a quarter cup of fuel
for a few seconds.
But I mean, it is a 520 cubic inch.
I mean, that's like crazy when you think about airplanes
and you think about an airplane engine,
520 cubic inches, that's immense.
The pistons in this thing are like this big.
So it needs a lot of fuel.
I think these burn 20, 25 gallons an hour.
So here's those injectors that we put
in the ultrasonic cleaner last night for a couple hours.
You guys saw what they look like
when I pulled them out yesterday.
I mean, they, for the most part, they look brand new.
So I like getting some anti-seize on anything
I'm going to expect to have to take out again,
especially on something that heat cycles so much.
I don't know if any of you have ever got this
on your hands before.
It's like a pain to get off.
It stains everything,
but I'd much rather have a couple of stains on my hands
than not being able to get something out that's corroded.
All right, so we got the three injectors in
on the left side of the engine.
We're going to get the three in over here.
It's actually kind of hard for me to work.
Not having any sleep.
And I'm so excited about this.
And my hands are a little shaky.
So yeah, so it's kind of hard to get these injectors in.
Last thing I want to do is cross thread one.
Nice, all right.
It's in, no cross threading.
So we'll get these things snugged up.
Go grab my torque wrench so I can get them torqued down.
All right, those are all torqued down.
We can get these fuel lines on here.
If you guys had a pilot's license,
which I'm sure a lot of you guys do,
or even if you guys don't have a pilot's license,
and if you did,
and you had the chance to fly an airplane like this,
where would you go?
You know, what would you do?
A lot of times as I'm working on this,
I am working on my pilot's license,
but as I'm working on this,
that's kind of what's going through my head.
It's just a little bit of corrosion in here yet, so.
Cleaned up, success.
All right, so got the manifold on,
got the fuel injection supply lines
on the left side of the engine.
Now we got to get the right side of this engine done.
Same thing.
That side went really smooth.
There's a little bit of wood on my toolbox there
to knock on halfway done with this here.
So I'm kind of getting a little bit nervous
as we get down to it,
because I'm hoping I didn't forget something
or that something's not going to go wrong here.
You know, I know a number of you even kept saying
something about, hey, you know,
just, you know, make sure nothing happens,
make sure this, you know, or that with the owner and stuff.
I really wasn't worried about it too much until yesterday.
So thank you for leaving those comments.
I mean, I read, I try to read all your comments.
I mean, there's been so many.
It's been hard, but I try to read.
I try to respond because the channels,
it's not just, you know, it's not just my channel.
You know, Rebuild Rescue is everyone's channel.
I really appreciate all the comments you guys leave.
You know, I appreciate when you share videos to other people.
I had friends of mine reach out and said,
hey, I got this video shared and here it's you.
So I love that.
It helps the channel out a bunch.
So the more you can do that, you know, the better.
You know, and I love hearing from you guys.
I mean, I love working on stuff
and I love doing projects and stuff like that,
but I mean, I think I love even more,
you know, hearing from you guys.
You know, what do you think?
You know, what am I doing wrong?
Let me know, because there's a ton of stuff I don't know.
All right, so this manifold's on, it's good.
We didn't cross thread it.
Three injector feed lines, a couple spark plug leads,
and then we're going to go get tugged
and we're going to take this thing outside
and it better fire up.
All right, so we got all the injector lines on.
We're going to get these tightened up.
Last thing we want is fuel spurting out
all over an engine that's going to get hot pretty quick.
Did you change the oil or anything?
Nah.
So we got all the injectors hooked up.
We have both pressure manifolds hooked up, all the lines.
They're good.
Everything's seated well.
Man, this is emotional.
So now we just got to get all the plugs hooked up
and try to unlock the turbo.
And then we're going to start this thing.
It's going to make some power.
Well, it's going to at least make some noise, hopefully,
and probably a lot of smoke.
Oh, and I went out and I grabbed some larger wrenches
so I didn't have to use pliers in the spark plugs anymore.
I guess I should tighten these spark plugs down first.
I thought you got bigger wrenches for that.
No, I only got one, though.
So I almost forgot, in my excitement,
to torque these plugs down.
That way we know they're in there and secure
and that we're not going to shoot one across the airfield
or tighten it down too much that we strip the head,
which would be pretty catastrophic.
You're coming to the end of something
and you're so close, you start rushing
and forgetting what you're doing.
That side's tight.
Upper plugs are tight.
Lower plugs are tight.
Wires are on on the right side.
Last one.
I feel like this one's taking forever.
So a couple of you had mentioned not needing the turbo
to be able to start,
which I don't know if I've ever started an engine
with a bad turbo.
Maybe I did and didn't know it.
We definitely don't need an air filter
that's falling apart and deteriorated, though.
And I think the intake on this is right here.
There's a lot of bird stuff in there.
So I am going to get the air hose
and I'm going to feed it down there
and just kind of blow out and see what comes out
because I'd hate for this to fire up
and then all of a sudden it'd suck a whole bunch of stuff
into the engine through the intake.
Try it the other way.
I think what I'm going to do when we go out to fire this up,
I think I'm just going to leave this open
so it can breathe just in case there's more debris in here
because I just don't want to see that
get sucked up in the engine.
All right, so this turbo is locked up.
I did find a socket that'll fit the end of the nut in here.
So that's the intake compressor wheel in there.
I'm going to get a socket in there.
I'm just going to try to wiggle it back and forth
and see what happens.
All right.
All right, so that's not coming loose.
I mean, it's frozen solid.
I put penetrating fluid down in here a couple of times.
We've heated it up with the torch off camera.
It ain't coming loose.
Like I could turn that.
I'm telling you, it's just going to break it.
So hopefully you guys are right that it'll start
and run without the turbo, that it'll suck past the turbo
because it's not coming out.
I mean, I guess if all else fails,
we'll just pull the turbo out,
but I think I'm going to try to start it with it in.
Hey guys, make sure you check out the motor store.
Really cool carrots, hats, mugs, all that stuff.
There's a link in the description.
Click on it, check everything out.
Like the video, subscribe, ring the bell
so you get notifications so you can see
all the cool stuff that we're going to be doing.
All right, so we have it out of the hanger.
We have the chocks on all three tires
and we got the biggest chocks that we could find.
So we're going to get the hanger closed up.
We're going to get the batteries out here,
get some juice to it.
And we're going to try to fire this thing up.
All right, so the battery's hooked up.
Everything's chocked.
Let's get inside and fire this up.
Clear prop.
Son of a gun.
Should be spinning over more.
Where's that starting fluid?
Right here.
Let me try that one more time.
Oh, I don't know.
Totally stumped.
All right, so it's not firing up.
I'm going to pop one of these plugs out.
See if we're getting fuel in here or not.
Seems a little wet.
Almost smells like it's firing in there a little bit.
All right, so I got all the plugs out.
I'm just going to hop inside and turn it over a bit
and see if we can get any fuel in the cylinders.
Hey, did you think?
Well, I think we're going to get it back in the hanger
and I'm going to have to look over a couple other things.
See if we can't figure it out.
I don't like the fact that we don't have oil pressure.
I think even, especially with the plugs being out
and turning it over,
I'm just feeling like it should kick over,
but it's just not.
Yeah, so let's get it back in the hanger.
I'm going to get some more stuff tore apart.
See if we can't get this figured out.
So we got the 401 back inside.
We couldn't get it to start.
I'm not exactly sure why it's not starting.
I mean, I spent all night last night
going over the whole fuel system
and pulled the whole thing apart,
cleaned everything out.
It still wouldn't start.
I'm not exactly sure if I missed something or what.
I'm just, I don't know.
The agreement was we had to get this airplane started,
not necessarily this engine.
So I think our best bet is to get some rest,
come in here bright and early tomorrow
and get working on the other engine.
See if we can get it fired up.
Make sure you subscribe, hit the like,
turn your notifications on.
Leave me some comments.
Let me know what you think might be wrong with us.
We have a lot more coming up on this project.
This 401 is going to start.
Thank you guys for watching.
