20HP Big Valve Predator 212 Runs!

Automobile Regency
59 followers
Oct 25, 2022
What is going on, guys? Before we finish up this head work and put our engine back together,
we have a very exciting announcement to make. For a long time, we've had a lot of comments
from you guys asking for a Cars and Cameras discount code for GoPowersports products. Well,
the day has come. Next time you make a purchase at gopowersports.com, use our discount code CC10
for 10% off your total purchase at checkout, and it's good for most items on their website.
It's a great way for you to get a good deal on some parts and help support us as well. Anyway,
enjoy the video.
Ike was out here for a couple hours yesterday, and I gotta say, the head's looking really good.
A couple hours? A little bit.
You told me like three hours. Was it more than that?
A couple is two. A few is three.
Okay, so a few hours. My bad. I gotta say, this head's looking really good.
The intake and exhaust is way opened up, and the exhaust is like a mirror. It almost feels like
when you freshly wax your car. It feels buttery, buttery smooth. So the intake is rough like it
should be, but the exhaust, it's literally reflective. It's been polished so much.
Since the head works, or the porting and polishing is done, it's time to cut the valves.
Then we can do the Play-Doh trick and figure out our valve clearance so we can shave.
So we have special handwritten instructions from Taylor at GoPowersports for this build,
and on the first tick here, check for clearance issues. Cam to crank. Almost all HEMIs need
clearancing, and I just now looked at that. The thing is, is really gotta have the cover on it.
Yeah. To hold these things.
The problem with making clearances to the crankshaft is you can unbalance the crankshaft.
So does that mean we should do all the clearance into the cam?
Well, here's the problem with doing it on the cam. The crankshaft
is hitting on the lobe of the camshaft.
So it can't come out of the cam.
Um, I can grind on part of the lobe, but...
I don't like that.
Maybe we can just grind a little bit off one side of the crankshaft,
and then grind a little bit off the opposite side?
Well, I know this one's hitting, but I'm gonna clear it. I'm gonna grind a little bit from there,
and then I'm gonna go to the opposite side,
and I'm gonna grind a little bit off here and here to try to balance it out.
It's just an estimate. It'll be fine.
So it's hard to see, but we no longer have any knocking, and you can't hear it anymore either.
Taylor wrote in, have fun, this will be a beast, dot dot dot dot, if you build it right.
What does that supposed to mean?
Well, he knows that we usually just throw stuff together.
We have a new, should be a bronze guide here.
That's fancy.
Yeah, so we're gonna be putting that on in the head. It should hammer in.
But as you can see, the new valve is bigger, pretty good size bigger, than the old valve.
You see right here, it's notched out, and the other one really isn't.
It's for flow, because when the air goes in, the stem is actually acting like a restriction.
So they have that little recess to help with the...
I'm ready to get this thing in there, dude.
And the third thing I noticed is that, look at the ends of the valves.
Yeah, the different keepers.
Oh, I meant the other end of the valve, like the faces.
Oh, well that one's solid, whereas that one's kind of recessed.
So technically, this one's probably going to give more...
Just that much more compression, because it's filling in that space.
Another thing we're going to be doing is a three-angle valve job in the head.
You don't want this full surface sealing on the seat.
It'll overheat and cause a burnt valve.
So you want the thickness of a fingernail sealing.
So that's where the three-angle valve job comes in.
It helps with airflow and keeps the valves cooler.
So if you're cutting for new valves, you're going to need a fancy toolkit like this.
And honestly, I don't even know what it does.
So what does it do?
Well, this tool right here should fit the guide.
The guide is like the...
Boom.
Okay, yep.
And you gotta put it in there until it gets snug.
You don't want to jam it.
If we cut these seats now and then put in the new guides,
the new guide might be off just a tad, causing it not to seat right.
Yeah, yeah, yeah.
Okay.
Probably should read the directions first.
Yeah.
So good valve seats are critical to maintaining compression and horsepower.
Poorly seated valves will not only cause compression loss,
but will also compromise the ability for the exhaust valve to cool itself
by transferring heat through contact with the valve seat.
Further, if the valve seat concentricity is outside of the allowable limit,
mechanical stresses may cause valve failure.
Mechanical stresses may cause valve failure.
So I'm knocking the factory valve guides out.
Go Power Sports threw in this nifty little tool.
That's exactly what it's meant to do.
You got them.
Yeah.
Oh, yeah.
Cool.
And we have bronze ones, right?
That's what they look like.
We're waiting on a call back from Taylor
because we don't know if we need to reuse the clips on these old valve guides
before we drive them in the new ones into the head.
So we're going to run out and get some lunch,
grab some pipe fittings,
grab a quarter-inch torque wrench so we can actually torque our rod,
and then get some Play-Doh, too, for valve clearance.
Where would the Play-Doh be?
For some reason, I feel like it'd be over here in the kitty, kitty, kitty, kitty, kitty section.
Oh, look.
Oh, my gosh.
So much selection.
What color are you thinking here, dude?
I'm thinking red like fire.
I'm down.
Yeah.
Sound good?
It's the same.
I think it's the same.
Dang it.
We can go with this one.
All right.
Red Play-Doh.
See y'all at the house.
So now I'm going to put these valve guides in the freezer.
Because we want them to shrink.
Yeah.
Right on top of it.
Let's go.
Make a run for it.
That about it?
That's good.
And that's how you install bronze valve guides.
The bronze bushings are not large enough for the valves to go through it freely.
So we have a reamer here.
And it should be the right size for what we need.
Needs to be right.
We're going for it.
Never done this before.
Feels good.
Okay.
We reamed the valve guides to fit the valve stem.
Yeah.
So now we are going to cut the valve teeth.
So you have a guide that you stick where the valve stems usually go.
And then the cutting tool goes around it.
Should we have oil?
Didn't say anything about oil.
The valve seats are cut.
Ike was a trooper on that.
You were working on that for what?
45 minutes?
Something like that?
Maybe an hour?
Probably an hour.
It was a while.
But they're together.
Or they're cut.
And the new valves are in.
Can break in.
We have to put the stock valve springs back in the head.
And run the engine at like 2,000 rpm for 20 minutes to break in the cam properly.
The way I look at it, if it doesn't break, we're in.
While we were at lunch, we grabbed a new torque wrench.
So we torqued the rod to spec.
Ike is just drilling and tapping that hole on top that was used for the governor.
And it's going to be turned into crankcase vent.
That's the idea.
Yep.
We don't recommend you guys doing this with a brass fitting of this size.
We ran around to our local parts stores.
And nobody had like a brass 90 degree fitting.
We're just not comfortable with like how small that border is there.
We're just going to get a brass plug and plug it off.
Because we can't tighten it to clear the fuel tank enough.
Ike put two bolts in the side cover just to keep the crankshaft steady.
Because we're about to do the play-doh test.
Play-doh.
And it's hitting already.
Excuse me?
Oh, hitting the play-doh already.
Yeah.
And I'm doing this without the head gasket.
So it'll give me just that much more clearance.
Oh, of course.
The pushrods and rockers.
Forgot all about those.
Let's spin it over.
I sure hope I don't open this thing up and just find the play-doh smeared all over the
cylinder wall and in the rings and stuff.
Oh, dude.
Open.
Oh, yeah.
I saw some for a minute there.
Still open.
Closed.
Yep.
Cool beans, man.
So we can take it back apart.
All right.
Here we go.
See what we got.
Oh, look straight down.
Yeah, they are pretty close.
Here's where the closest point is here.
Yeah.
We're not shaving that.
We're not shaving the head.
Wow, breaking news.
I was, oops.
I was, man, I thought we were both pretty set on shaving that head.
Okay, well, maybe we can do it a little bit just to clean up the surface.
Yeah, I'm down for that.
I think that's it, bud.
Perfect.
Back to the shop.
Got our ten thousandths of an inch head gasket.
All right, the head should be on for the final time.
Yeah.
All right, so factory valve springs are in it because we need to break in the cam for
20 minutes, but we're slapping this brand new 24 millimeter carburetor on here.
They have a special adapter for your intake.
You got to plug this hose on it.
They also provide, I don't know how far to go on it.
I'm assuming pretty far.
Oh, my Lord.
I think the shorter the better, right?
Okay, that'll work.
This 24 millimeter carburetor is not to be used with an otherwise stock engine.
Like once you do your head work, your porting, your polishing, maybe even your valves and
definitely your valve springs, you know, you get a lot of air moving through this engine
at high RPM.
That's when you want to look into a 24.
But if you have an otherwise stock engine, a 22 will work.
So our engine is all together.
It has oil in it.
It has fuel in it.
It's just sitting on the chassis.
Nothing's hooked up.
But we wanted it bolted down so it wouldn't wiggle all over the place and potentially
fall off something and break.
So, yeah, we were about to fire it up and run it at 2000 RPMs for 20 minutes to break
in the cam with the stock springs in it.
Then we can take the valve cover off, put the 26 pound springs in.
Cool.
All right, so 20 minutes.
Our cam should be nice and broken in.
Time to put the 26 pound springs in it, right?
Yep.
And then we can.
Probably should wait for this guy to cool down, but yeah, we're not going to.
And get her on.
The oil is just like napalm.
Wow.
Yeah.
Don't try this at home, folks.
Wait for your oil to cool down.
I didn't think I put it in there that time.
When you take the spark plug out.
It's going to probably burn me.
Yeah, let's get a rag or something and I'm going to read it.
Ike was talking to a buddy of his that has a motorcycle dyno that has like a sniffer,
he called it.
Anyway, it reads like the exhaust.
It's kind of like an air fuel ratio sensor deal.
So we may be doing a little bit of dyno tuning on this guy.
Is she fat?
Yeah, she's fat.
I can tell you she's fat.
Yeah.
Nice.
Oh, you all right?
Yeah.
Don't drop it down anywhere.
It ain't going to go nowhere.
I don't want anything to fall down into the block.
That would be a disaster.
Let the fun begin.
Oh, yes.
There's two.
All right.
Okay, that looked like all fun and games.
Oh, getting it out is the easy part.
Getting it back together.
Yeah.
We had a hard time with the stock springs and like 18 pound springs are really difficult.
These are 26 pound springs.
All right, let's do it.
Did you want this?
Do you want something else?
So we got both valve springs in, Ike's putting the keeps in, and the push rods.
So valve cover, header, fire it up.
And you're going to turn it.
I mean, just a little bit.
Just enough to upset the parents.
Yep.
I want to hear it sing a little bit.
Now, I had to crack the throttle some.
You had to crack the throttle?
All right, I have the choke on, so I'm going to see what it's like.
Yeah, I had to crack the throttle.
Oh, you have it on top of that?
Yeah.
See what you're doing.
All right.
Sounds pretty good.
Dude, it's like the NASCAR engine of go-kart engines.
So we're going to see how this engine performs in the daylight next time.
I think it's going to haul.
We got some testing to do with it, though.
Now we're going to go for a top speed run.
And Ike's buddy also has a motorcycle dyno we might be able to throw it on.
That'll be a lot of fun, just to see what kind of power it throws down.
And we can do some tuning on it as well.
Anyway, be sure to check out all of the products we used for this performance build.
Links in the description, as well as the American Express 2.0.
Link in the description to that, too.
Got to thank gopowersports.com.
Thanks for watching this video, guys.
Check us out on Facebook and Instagram at carsandcameronsreviews.
Check me out at IsaacItWillBeFun.
And subscribe to the channel if you have not already.
And press the bell for notifications.
And smash that thumbs up button for us if you enjoyed the video today.
Anyway, support the channel.
It really helps us out when you guys buy our stickers and t-shirts at cars-camerons.com.
Thanks for watching.
See you next time.
