Large and small containers are used to make several examples of 6 layer density column of using salt, water and food coloring. What's nice about using saltwater instead of sugar water is the columns can be left to sit for several weeks and will not spoil or form mold like sugar water will. Initially, the layers form distinct boundaries but as it sits the different concentrations ail slowly diffuse and show a nice transition from one color to the next.
this video is being reposted with changes due to some copyright issues
AI Generated·May contain errors
Video Summary
AI Generated
This video demonstrates how to create a rainbow density column using saltwater solutions of varying concentrations. By dissolving different amounts of salt into water and adding food coloring, the presenter illustrates the scientific principles of density, buoyancy, and saturation, showing how liquids with higher densities sink below those with lower densities.
Hi, we're Shane and today I want to take
a look at some rainbow density columns.
Now this is a very pretty demonstration
and it's also a good way of understanding some
science concepts.
We have solutions taking place, we have buoyancy, we have density.
So let's take a closer look.
The layers are made by dissolving salt into water
and then adding food coloring.
This table shows the amount of salt that should
be dissolved in 100 milliliters of water and
then the corresponding drops that should be added to it.
If a balance isn't available,
you can use a half a cup of water and teaspoons.
Now let's take a look and see how to put this together.
My first step will be to measure out the salt according to the table
and add them to corresponding
containers.
Next, I'm going to add 100 milliliters of water to each container.
Note that the final container doesn't have any salt,
it will just be water by itself.
Now it's time to add the food color.
My first container is going to be purple,
and that's a mixture of red and blue.
Now it's tough to get purple to look nice,
so a lot of times I'll just go with five colors.
My blue, green, yellow,
and orange is a mixture of red and yellow.
my last container is the red.
I also need some small pieces of this foam cup. Now
that we have our solutions mixed,
it's ready to add them to the graduated
cylinder. I'm going to start
by putting some foam pieces in here. That's going to
keep the layers from mixing as I'm adding one
on top of the other. I'll add
the purple first since that's the densest,
and that one I can simply pour
in. Now from here on,
I'm going to use a funnel with a small tube attached to it.
Now I have seen instructions around for using sugar,
but personally I prefer to
to use salt. Salt is a lot cheaper.
If you spill something and that usually happens sugar is going
to be very sticky but the biggest problem
is that the sugar solutions will eventually get mold on
them. With salt solutions I like to leave them around
for a couple weeks and mold is never a
problem. The layers stay separated
because each color is at a different density. The least dense
is at the top because it had no salt dissolved into it at all.
As we proceed down the column
each additional color had more salt added to it.
It made it denser so it's able to
support the color above it.
Now when we added the salt to the water, it broke down
and attached itself to the water molecules.
We can keep adding salt until
it becomes saturated.
Now if we want further evidence that the density is
decreasing as we go up this column,
we can use a homemade hydrometer. A hydrometer
measures the density of a liquid
by comparing its buoyant force to that of
pure water. To get the value of one gram
per milliliter, I put it into pure
distilled water, noted where it was,
then put a mark on the straw. The second mark
is for a saturated solution of saltwater,
which has a density of 1.2 grams. Now
let's test our other solutions and see where they fall. I'll stick the
hydrometer in each solution
and then mark it with the respective color. First
the red, then the orange, here's the yellow,
the green, the blue, and finally
the purple. As we would expect,
we can see that the density is increasing as we go
down through the colors of the column.
Now what would happen if I added my
hydrometer to one of the density columns.
I think it would fall somewhere in
between, but let's try it.
Now this would vary greatly depending on which column
we put it in, but as you can see it does fall somewhere
in between. Now we can
make these in a variety of containers.
The next one I want to make is this
large tube here. I have styrofoam in the bottom
and a long hose with a funnel at
the top.
We'll add
the densest
material
first,
the purple,
and there
we go.
Flat-shaped graduated cylinder.
I have no idea what these bulbs
are for, but I like
the shape of it so we're going to try and make one in here.
I had some difficulty keeping
the colors separate so I just went with blue, yellow and red.
I decided to try it in a few
more containers I had sitting around the room.
Now I want to try this one more time. In this
case it's a four foot long plastic tube.
It's actually used to protect fluorescent lights
and light fixtures. It has a rubber stop in the bottom,
the foam is sitting there, the
long tube
is sitting here.
Now let's add
our solutions.
They're
absolutely
beautiful. Now
the best thing about using salt solutions
is I can let these sit for a number of weeks
and the colors will slowly diffuse one into the other.
By the way, I'd like to thank you for stopping
by and come back and see me again.