Atmospheric pressure powered car // Homemade Science with Bruce Yeany

Bruce Yeany
137 followers
30 Video Views·May 8, 2022
Here is a small car that is uses the atmospheric pressure as a medium for storing potential energy as a power source. It follows the initial project of using a larger water squirter toy on a car of similar design. In this case, a small syringe is stoppered at the tip and when the plunger is pulled out, the differential between the inside of the syringe and the atmosphere outside of it can be used to supply the turning force on the rear axle. A string wrapped around the rear axle supplies the torque giving car distance close to 100 feet. A second method of using a pulley system to increase the power supply range but reducing the torque is introduced but appears to need some additional modifications ( still a work in progress).
Headed for the wall. Don't let it hit the wall.
Hello, I'm Bruce Shaney and today in Homemade Science we're going to take a look at some more
atmospheric powered cars using the atmosphere to store potential energy to drive a small vehicle.
Now before we use these large water squirters this time we're going to try it with these
much smaller syringes. Now this is the first vehicle that I made and it worked fairly well.
This piece is currently going about 200 feet. Now this water squirter has a capacity of about
200 milliliters. Our first attempt is going to be with this syringe which has a capacity of about
12. No matter the size the concept is the same. Seal the end of the tube and pull out the plunger
and you create a vacuum inside that tube and it's the atmospheric pressure pushing that plunger back
in again that's going to drive the car. All right we have the car built. Let's take a look at it and
then we'll give it a few runs. The body is plywood. The wheels are these CDs that are mounted on these
wooden blocks. The axle is a wooden dowel and they're supported by these little blocks here.
The block has a groove cut in it and then a plastic tube was glued into that channel.
Putting it back together again the wheels are simply held in place by friction.
There we go. Next I'll add some rubber bands to give the wheel some additional traction.
To power it a string runs from the plunger to the axle. The string has an eyelet on it which
catches in this small hole. We can wind it up about three times and then it's ready to go.
I wasn't ready for that. Mr. Yang!
I was hoping to do a little better. We're getting about 20 to 25 feet.
Well we did get some movement out of it but I think it's a little bit too underpowered with
this 12 so I think we're going to try it again this time with a 20. It's still the same vehicle
it just has a larger syringe on it. That's pretty good.
It's getting better. Now we're hitting about 45 feet. I thought I'd update this one more time.
Originally I started out with this 12 milliliter syringe then we went to a 20. Now I'm going to
try it with a 40. Now to do that I had to change the back axle. The axle is now a metal bar which
is reduced in size in the center. This will give me more turns on the axle but less torque on the
wheels. I found the easiest way to wind it up is simply to move it across the table.
Well that's a good bit farther than the other one. With the longer distances now
we're having trouble controlling it in the hallways. And boop! Right there it goes.
Back down to the gym where it's wide open our best runs are about 90 to 100 feet.
Now so far we've been going directly from the syringe to the rear axle.
I thought maybe a pulley system could give us additional distance. The plunge is now pulling
on an axle with a larger pulley on it down to a smaller one. That should decrease the torque
but it should increase the distance that it would travel. This is using the 20 milliliter syringe
and we're getting about 22 to 23 feet. Well that was certainly disappointing. I figured the rubber
band wouldn't be very efficient but the rolling resistance doesn't feel that bad. Well obviously
this one's going to take some more work. I have some ideas but if you have any suggestions I'd
love to hear them down in the comments. Now I do hope to make improvements in all these vehicles
and hopefully share them with you in the future. In the meantime if you want to see more vehicles
that are powered by the Atmosphere or rubber band powered cars please check out the other
videos on my channel. In the meantime I want to thank you for watching and come back and see me
again. Okay, bye.
