Metric threading with Dalton lathe

Screw Driver
87 followers
#machinery #motorbikes #occupations #career
Metric threading with Dalton lathe
AI Generated·May contain errors
Video Summary
AI GeneratedThis video demonstrates how to cut external metric threads on a lathe, specifically focusing on a 12mm diameter with a 1.75mm pitch. The presenter covers the necessary gearing setups, material preparation, and the specific operational differences between cutting metric and inch threads.
I've got a 12 millimeter nut here. It's a 1.75 millimeter pitch. I'll cut some external threads
just to show you what the metric threading looks like. I said on an earlier video that the only
place you're going to find the metric thread chart is in this book here, but I've forgotten
this fell up in Oregon, Dennis Turk. He reprinted or reproduced that thing
in here along with some other information. So that's one place you can find it. Another place
if you go in at the Dalton Lathes Users Group and join, you can look up the files
and this book has been reprinted there also. I don't know if this shows up here or not, but
for a 1.75 millimeter pitch, you need a 35 on the stud position,
a 127 and 125 at the compound position, and a 50 tooth gear on the
screw. These are the transposing gears here, 125, 127, and there's a gear bushing here to
put them both together. If you're just going to use one of them, there's a key here, a keyway here,
and a keyway here for the eighth inch key if you want to use one of the other gears.
So here's the gearing for a 1.75 millimeter pitch. Got a 35 driving a 127, which is coupled
with 125 driving this screw gear here, 50. Got a piece of 12L14 steel here. I've turned it down
to 12 millimeters and I've also taken another five thousandths off. The way I was taught was
take five thousandths off your nominal before you start threading. Then I cut a thread relief in here.
I wasn't sure how deep to make that, so I just measured the inside the net with a pair of
calipers. It's probably not going to be deep enough, but I can clean up the thread relief when we're done.
Now cutting metric threads, it's a little bit different than doing the inch threads, because
we're not going to use the thread dial. Once we engage the half nuts, we're just going to leave them
engaged until we're done. Whenever you're threading, you'll probably be using the back gear,
so don't forget to oil the cone pulley and the back gear itself.
It's pretty important that you have that lubrication, especially on the cone pulley.
Okay, we're going to make our first pass here. I'll just do a scratch pass and check the
the pitch with the thread pitch gauge.
Touch with the cross slide and zero it.
Put a couple thou in here on the top. Once we engage the half nuts, we're not going to release them.
Pretty faint, I don't know if you guys see it or not. We'll withdraw the cross slide and turn
the motor off at the same time. It's pretty faint, but I think I can read it.
Looks like it could have been a little bit deeper, so we'll reverse now.
When you're just hardening, use the back gear, but I tell you, I think I can thread in direct
gear without the sponsor's load, but I'll leave it here just to show it. We'll get down in there,
re-zero the cross slide, and we'll start with 10 on the top slide. That's still pretty order.
When we get down to our center reef, we'll turn off the motor and withdraw the cross slide.
And back up. It's pretty light, I think I'll take 10 more.
Zero on the cross slide, and I'll take eight this time.
Well, it's not so slow, I'm going to fall asleep here. So it was eight, take another eight.
Almost like a thread. No, got a ways to go yet. I'll take five. Do the cross slide here.
Let's take three. Zero the cross slide here. I might redo this video at a faster speed.
Well, pretty close. A little tight, but I'll do a spring cut. Zero the cross slide.
If anything comes off, it should be on that pad. If I was doing this for real,
I wouldn't be in back here. I'd be in the slowest speed in direct. So when you're just starting
out, always use your slowest speed. It fits on here, but it should be looser.
Other than that, it may not fit. I'll dial in about a half thousand.
A little more is coming off.
That's pretty good.
Yeah, that's better. Might be even a little bit loose, but I'm sure it's still with intolerance.
You want a little bit of clearance because these things are mass-produced, they're not always the
same. I'm going to disengage the half nuts now because we're not going to be doing any more
threading. Well, it looks pretty good. Might be a little bit loose, but I think it'll be all right.
A couple times I threaded with just a nut, and then you get another one made by somebody else.
It can be tighter. Anyway, you get the idea. Just play with it. You'll get it.
