Join me in the machine shop for the lathe restoration. This is an engine lathe (or metal lathe) that I inherited from my grandfather and it is a metal machine tool used for metal turning and thread cutting, among many other lathe uses. During this machine restoration I will be getting into a little bit of everything including the lathe chuck assembly, power feed mechanisms, tailstock alignment with a dial test indicator, and even lathe safety. And who knows, we might even make some metal chips on this fine piece of industrial machinery.
TIMESTAMPS
0:00 Intro 1:22 General Cleaning 4:11 Electrical Inspection 6:30 Chuck Restoration 8:40 Ways, Lubrication, and Tailstock 12:19 Carriage 13:07 Power Feed 14:29 Threading 15:20 Wrap Up
AI Generated·May contain errors
Meet the lathe. This lathe is one of the several machines that came from my grandfather's shop.
It's an older manual style lathe from the early 90s. Over the years I grew up using a lot of
different machines, but this one became my favorite for many reasons. For one, I just
love the way it looks. It's like a big dense block of mechanical precision. The knobs and dials and
hand wheels are all perfectly shaped and located for operator ergonomics. And because this is a
fully analog machine, everything is out in the open, meaning you can actually see all of the
individual functions, which I like better than modern CNC machines that are just fully enclosed
boxes hiding everything. The only downside to this machine being fully exposed is that it makes
quite a mess. Metal chips, oil, and coolant tend to get everywhere. And after sitting unattended
for a few years, this machine looks pretty rough. So let's get it cleaned up. My grandfather was a
smart man, and in his infinite wisdom he had the forethought to put this 4,000 pound machine on
wheels, as well as all the other heavy items in this shop. So in a matter of minutes I'm able to
move everything out of the way and get the lathe out in the open. For as large and unwieldy as this
machine is, those pivoting casters on the one end make it not so bad to move. Now I can start
cleaning. Fortunately most of the surfaces are painted, so the rust isn't bad. Not so fortunately
there are a lot of surfaces. Much like on the mill cleanup, all the grease and dust and chips
doesn't really hurt anything. But like I said, this is my favorite machine, so I want it looking
spiffy. This end of the machine with all the knobs and levers is actually two gearboxes stacked on
top of each other. The top one is called a headstock, and it houses a spindle that a chuck
can be mounted to to hold your part. This spindle has eight gears ranging from 76 RPM to 2,000 RPM,
and they're changed using these two levers. The second gearbox is kind of this middle section
here and is for controlling the feeds and threading features. As you can see there are a
lot more knobs and levers here, with a lot more settings. I'll play around with these more once
I get the rest of the grime off. Moving on to the backsplash and containment tray, it's pretty
obvious this is where all the mess went. I guess that's to be expected given their names. While I
can clean a lot of the surfaces while they're still mounted to the lathe, a lot of the areas
are straight up inaccessible. Off they come. On the floor I can really put some muscle into scrubbing
and see how gross they actually are. Clinged up there are some flakes in the paint, but I think I
can live with this. It won't be long before these are a mess again anyway. The chip sludge also made
a pretty big mess on the metal casting under the chuck. This metal casting is actually one single
piece making up a large portion of the gearbox and extending all the way to the opposite end
of the lathe. The top surface of this hunk of iron has perfectly smooth ways ground on it.
The rest on the other hand is not perfect and definitely not smooth, which makes it a bear to
clean. Many times I had the urge to bust out a die grinder and go to town on some of these bumps
and whatnot, but my judgment got the better of me. These are not super visible areas to begin with
and will also be a mess again before too long. Cleaning in and around all these tight areas was
a bit tedious, but I gotta say the payoff was worth it. This is already starting to look like a
different machine. Honestly I've never seen it looking this good. Now not only do I love this
because it looks cool, but it also sounds pretty badass as well. When this thing turns on it sounds
like Optimus Prime booting up. Way more industrial sounding than you would think from this small
machine. While the lathe obviously does turn on, there are a few other electrical features I want
to confirm are working properly. To start I'm looking at the source of all the controls, the
main electrical panel. I just need a key. It should be around here somewhere. If only I could find it.
Almost as if the designers of this lathe anticipated this problem. They put an override
screw on the door. Thanks guys. Oof, that's not super encouraging. Looks like some mice have been
having a little party in here. Vacuumed up though this doesn't look so bad. No chewed wires, no loose
connections. This is honestly a miracle. Even though this looks good there are a few other
electrical features on this lathe I want to check out. First is the drive system door switch. This
is a redundant safety preventing the motor from turning on if I have this cover open.
That would be really bad for my fingers so I'm glad the lathe has my back. Next is the emergency
brake. This red foot pedal on the front of the lathe should actuate a mechanical brake on the
main motor shaft. It should also trigger a limit switch that cuts power to the motor.
Just like that. Alright with the safeties working perfectly let's move on to the light.
The bulb was busted so I swapped it with a new one but I still don't seem to have power here.
Yes it's plugged in. After busting out the multimeter and spending an hour troubleshooting
I found out that the light works just fine. It's my brain that's faulty. Note to self,
110 volt bulbs don't work in 24 volt sockets. I suppose I should have checked the electrical
diagram first. I do have one problem that definitely does exist though and that's the
coolant pump. This one doesn't seem to turn on but since I don't intend to use it anytime soon
due to the small scale of work I'll be doing I think I'll just kick this can down the road a bit.
Now just because the safety features are working properly this can still be a very dangerous tool
to use. In fact that is actually another one of the reasons it appeals to me. There's an inherent
element of risk in using a lathe but it's a risk that can be mitigated by proper techniques setup
and focus. All of which are 100% in my control. The chuck of the lathe probably poses the biggest
element of risk. If it's not spinning really fast it's spinning with a lot of torque and
is basically unstoppable. For the sake of the queasy I won't elaborate but you get the idea.
This particular chuck is called a three jaw for obvious reasons but it has seen better days.
It's covered in rust and also seems to be a bit gummed up inside. So let's take it apart.
With everything apart I can see why this chuck was hard to use. The old oil in here seems to
have partially solidified into a sticky gooey substance. Cleaning this up is a perfect job
for the parts washer. The solvent worked through the former oil with ease and even
got a head start on the surface rust. But there is definitely more rust here to remove.
Since I'm feeling a little frisky I'm foregoing the rust converter for some old-fashioned elbow
grease. Scotch-brite pads and penetrating oil actually made pretty quick work of the surface
rust. To lube all these gears and whatnot they do make a chuck grease but I didn't have the
forethought to order any. So instead I'm using motorcycle chain lube. By my thinking if it's
tacky enough to stay on a whirling chain it should work well not to fling off of this chuck at speed.
Back on the lathe this chuck looks great and cleaned up way better than I was expecting.
Now because this is a fully manual machine the parts made on it are a direct result of my human
inputs which is a challenge I really enjoy. The operator inputs on this and most other lathes
are done through the carriage, cross slide, and compound rest. Each of these are controlled by
hand wheels that move the components along precision ground ways. The largest of these
ways are the ones for the carriage and these actually make up the z-axis not the y like you
might think. I actually only recently learned this little tidbit from a viewer so if you're watching
this thank you. Because these carriage ways are fully exposed along the length of the machine
they're relatively easy to clean. Some mild scouring with a scotch-brite pad and a few
light passes with a whetstone to smooth out any nicks and they're looking good as new.
The cross slide and compound rest on the other hand will need some disassembly to get at the ways.
But while this is still mounted here I'm going to go to town on this rust.
That looks great, even matches the sheen of the chuck. Easing the cross slide assembly off the
carriage reveals some bad news though. There isn't any damage but that oil definitely shouldn't be
black like that. I'm pretty sure this hand pump should be pushing oil to these ports but I'm
getting nothing. I'm also not feeling much resistance in the pump. Let's see what's going on.
This is a good excuse to drain the carriage oil and refresh it anyway.
With just a few screws I pulled the hand pump off the side here and actually discovered it
has two plungers. The second one seems to be actuated by a cam on the carriage handwheel
so it works sort of automatically. No problems that I can see here, must be something inside
the carriage. I removed the oil pickup assembly and spotted a potential problem.
There was a check valve inside this elbow fitting and it was completely locked up.
Got it cleaned up so we can put this back together and see if that fixes the issue.
Still nothing. I can hear the check valve ticking and feel a little more resistance.
Oh and oil is coming out on this way but not the others. The only other place I can really access
is this distribution block from under the carriage and it was definitely gummed up with old oil.
As were the ports leading to the ways. With some thin wire, brake cleaner, and compressed air I
have these cleaned. Moment of truth. Atta boy. With that issue resolved I can slip the cross slide
back on and install the gib. The gib is basically a shim and lets me adjust the play between the
ways. I only want this tight enough to remove the free play but still be able to move the
handwheel with ease. The compound rest is a similar story. Clean it, lubricate it, install
it, and adjust the gib. The last piece of this stack is the quick change tool post.
This is the part that actually holds the cutting tools and it's called quick change because well,
you can change the tools quickly. One final thing to take care of up here is the tailstock.
The tailstock can hold various tools like chucks for drilling holes or centers for supporting long
work pieces. One thing I do want to check is that it's centered with the spindle. Mounting a dial
indicator in the chuck I can sweep through the inner mounting bore of the tailstock to get an
idea of how far off center I am. Looks like it's too far to the side by a few thousandths as well
as too high. I can adjust the side-to-side position with these two adjusting screws.
The height on the other hand is a trickier problem to solve. Since there's no vertical
adjustment it looks like I'll have to either grind or mill the height at this interface.
Sounds like a problem for another day. The last bit to clean up on this machine is the carriage,
feed rod, and lead screw. The carriage houses the handwheels for the x and z axes as well as levers
for engaging the feeding and threading features. Easy muscles. There are a lot of really tight
areas covered in a film of grease and oil. Fortunately this film protected everything
from rust so it was just a matter of getting in there with some small brushes to get everything
looking new again. That looks so much better. The feed rod and lead screw were also almost
completely rust free and basically just needed a good wipe down and re-oil. That just leaves
one last surface to clean and I'm done. Everything is finally clean. I've mentioned this lathe has
some pretty cool power feeding and threading features so let's take a look at these.
Both of these features move the carriage of the lathe to perform cuts automatically.
Power feed moves the carriage through a drive connected to the rotating feed rod
and threading moves the carriage by engaging with a rotating lead screw.
All the feed rate settings are laid out on these two charts. Most of the settings can be selected
with these three levers but there's one setting that takes a little bit more effort. The change
gears. This lathe came with a whole set. Oh hey the electrical panel keys. I knew I'd find them
eventually. The change gears are located behind the pulley cover and have to be physically swapped
out for other gear combinations depending on what setting you need. Once the gear combination is
swapped it's helpful to mark the chart so you don't have to take this apart to remember what
combination is in here. Ask me how I know. All right time to check up some metal and make some
chips. First let's do some cleanup passes with the power feed. This is another reason I love this
machine so much. Watching the smooth and consistent removal of metal is almost hypnotizing. Though that
smoke from the cutting fluid is a bit concerning. I don't think it's supposed to be doing that.
If anyone has cutting fluid recommendation let me know. Now I want to make some threads. I want a
pitch of 10 threads per inch so with the machine off I can adjust the gearbox levers according to
the chart. On the carriage I engage the thread dial with the lead screw. Since cutting a thread
will take multiple passes this dial helps me make sure I start the thread feed at the exact right
time so each pass lines up with the previous one. With everything set up and the lathe spindle at
its lowest speed I'm ready to cut. When the O mark on the dial comes around I engage the thread feed
with this lever and we're cutting. Watching that tool line up perfectly with the groove is so
satisfying. After a few more cleanup passes and a parting cut I have a finished part.
I'm not super impressed with the finish here so I'll have to see what's going on.
Regardless this part will work just fine as a rest pin for the hydraulic press.
So there you have it. After two weeks of cleanup this lathe hasn't looked this good since it came
from the factory. Without the grease dirt and grime you can really see the beauty underneath.
It's going to be such a pleasure making parts on it again and I have a few things in mind.
So let's get to work.