My £450 Golf Finally Has TWIN TURBOS!

Tech Care
3 followers
Sep 15, 2026
AI Generated·May contain errors
Video Summary
AI GeneratedThis video documents the 11-week fabrication of a custom twin-turbo exhaust system for a mid-engine Volkswagen Golf with a 3.2 VR6 engine. The project emphasizes a balance between functional performance and a striking \"jigsaw puzzle\" aesthetic, culminating in a successful reveal for the builder's son.
We've now got twin turbos in the back of our Volkswagen Golf, but this started as a £450
wreck that had been abandoned for years. And for some reason, my son decided it needed a
thousand horsepower. So we cut the float out, we put a 3.2 VR6 in the back, built a roll cage
and mounted both the turbos. But bolting them in was only half the job. Today, we're going to
connect them to the engine. That means building our own exhaust manifold and figuring out how to
get all those pipes to fit in the bay. But the first process of that, for me, is always the
collector. And what a collector is, is it's where all the exhaust tubes come in and collect in the
same area. We're going to have three going to one turbo, three going to another turbo. So we're
going to have to collect the three pipes in one area. We're cutting six tubes, then we're going
to put them in the bandsaw and we've got a jig. And the jig holds it at a specific angle and that
should give us our three into one collectors. Obviously it's hard to do because I need two
sets of hands, but if you put two there and one there, yes, it needs a bit of fettling on the
flat wheel, but you can see now you're three into one. Wonderfully fit. That one's got a little bit
of a gap, but I can always sort that out. But awesome. So now I need to attach this to the
flange because this is where the turbo bolts up. Ignore this, this is for a twin scroll turbo. We
eat one but the flange is there. Chop this down because it's far too small to film there. So the
three into one collectors are now all welded up. And if you look at this block, the reason why I
bolted this block is to keep this flange as flat as possible. Because what you find with welding
is when you put a load of heat into it, it can warp the flange. And as much as you can eradicate
that, the better. Also, before the people put in the comments that should have back purge, let's not
dig into that. Let's not get the Instagram welders involved. This is good enough for the girl's
high day. Let me tell you. Right. So there's no right or wrong way of doing this. You've just got
to choose a port to go to the port and just get your jigsaw. I'm thinking obviously it's got to
come around there. So we were going to put a 90 around here somewhere and maybe space that out.
I've got to clear this water jacket here. It's just about making it up, visualising it
and feeling out and seeing where it ends. Nice. And that is runner number one completed. One's
done. So that means I'll put some more tacks on it. I could take it off. I don't know what I'm
going to do yet. I could take it off, put it on a spare head and then work on the next one.
But I'm actually enjoying coming in and out of it and seeing how it visually looks with the rest of
the car. Let's crack on. But one down, five to go. It's horrible, horrible. Can't do it. Oh,
missed it. Love it. Got one tack on. It's always in the right spot. It's not bad. It's not bad.
Oh, the joys. One man fabricating. That's got it. That'll do. Happy with them two.
Now I can start filling in the middle and start making it look epic. But to give people an idea,
I think each one of them's taken a couple of hours each. So about four hours into
them two tubes. People could body them faster, but this is how I do it. And also to add,
any Instagram welders that are going to comment, this should be equal length. They can get lost.
Yeah, we'll get that. Like a glove. Three out of the six done. So now this one is going to go to
that one. Now understand for me, anyway, you're making these manifolds. It doesn't really matter
what port on the turbo goes to what port on the engine. You've just got to join them up.
And in my case with this build is, it just has to look good because
as much as I want performance, it has to visually look incredible as well. So that's now the right
hand turbo all done and dusted. All tacked up. Obviously still going to weld around it all.
I think actually there was a good comment, split the flange and have two separate manifolds. I
think I'm going to do that. But as I keep stressing, there is no design with these.
There's no like, it has to go this way, in my opinion. You could literally just put a bend in
a straight. It wouldn't look as cool as loads of little bends and just tucking it in nice and neat,
but just make it up as you go along like a big jigsaw puzzle. So now it's on to the final two
to there. So when a box like this arrives, I hope it's car parts, but it's not. It's a mattress.
And this is today's sponsor, Emma Sleep. So let's get this box opened.
It comes rolled up like this. Once the wrap is off, you unroll it and leave it to expand.
This is the Emma Original Pro with seven layers with thermo sink for temperature regulation.
And it has memory adapt foam, which allows the mattress to mold around
the unique shape of your body. And they have sent us their comfort cooling pillars,
which are breathable. They are microfiber filled and they have an outlast cooling layer. So Emma
offer up to a 200 night trial and a 10 year guarantee. So you've got time to get this home,
get it unwrapped and make sure you're happy with the product. Their back to school sale has up to
35% off and use my code TWIN to get an extra 5% off your order. Click the link in the description
to find out all the information about Emma and their products. So let's crack on now and get,
let's get back on with the golf. So I know it's being picky, but if I put that there,
it's a bit of empty. In fact, no, I'm going to need to actually, because of that bolt.
Yeah. I'm going to have to do it there. I don't really like it. I look at a 90 there.
Might put a 90 on there. I don't know yet. Yeah. I don't like this gap, but I'm going to have to
and five out of the six don't burn me finger. I don't want to say one of these welds,
but the gap here is so I can get that bolt out, but I hate it. I would like to put a bit more
tighter and then add it come on an angle, but I had to clear. So I think when I do this one,
now the last one, I'm going to bring it across here, try and fill this area up for visuals.
And then into the two hours later. So we are done. All the runners are finished. And what's
mad is from the original jigsaw bags. That's all that is left. One and a half ends are little bits
of pieces, but just look at what we have created. It looks insane in there. That's going to look
mega when he saw welded up, got to put wastegate takeoffs in the collectors at some point.
So the next step is this jigsaw, which is all the exhaust. This is full of
multiple bends, full length of three inch. We're going to make the exhaust system,
but we are one major part missing. So I need to get on the road. I need to get that picked up.
It's seven 30 at night and we're in Shrewsbury and we have come to pick up
an R32 bumper and side skirts. This is the reason why I couldn't carry on
is because how do I know where the exhaust tips are going to go?
So let's throw it in the van. Let's get back to the workshop. We have purchased
two giant exhaust boxes and two flexes. The reason why we bought these just off the shelf
rather than make them is the 50 pound each. I couldn't make them. Probably the cost of material
would cost me more than 50 pounds. So these are prepped. We start fitting them in the car now.
First job I've done is I've machined the flange out with this lip. Now as much as a three inch
flange, I've machined the lip and the reason for that is so that sits in there really, really snug,
which actually picks up the flange for working with, which means I can put it in the bay
and I can still rotate it before tacking it, which means because everything's got to be symmetrical,
I can tweak it a bit so it's all in line with the center X. Plus the flexes had a really snug fit
so you can get them in place. So it's just a case now of keep adding and keep adding until you get
to where you want to be. So my next challenge is I need to do an X-pipe where these two are
kind of together. I've never built one and the reason for doing this is I'm hoping to run one
lamber sensor. What that does is it maintains the engine's air and fuel ratio compared to the ECU,
but if I've only got one lamber sensor on one bank, it means the other bank could run rich or lean
and melt itself. So if I have some kind of X-pipe, hopefully that will join the gases
and the sensor will work. So let's challenge myself to get this done. Nice, really nice.
I am well happy with how this has turned out. Look at that, well chuffed of it, welded nice,
everything's just come out nice and this is gonna look absolutely mega in like this area.
Let's cut them two pieces now and let's get it joined. It's gonna look great.
Let's get that welded on, come on.
Just look at it. Oh, that looks mega. All the X's in the middle. Oh, it looks brilliant.
This is what happens when you let a fabricating enthusiast wild and just let his mind run.
This is why cars are a bit boring these days. No one's doing silly stuff like this just because
it looks great. I'm well happy. So I think we're going to have an exhaust post here and we're
going to send one of these pipes off over this way around the cage and into the box.
I am well happy with how this is turning out. Just going mad wild, making it look cool.
Look at it. So the next job now is, obviously these are getting welded on,
they're just clamps just so it holds everything in place so I can look at it.
I need to put two of these in. Let me just put it on.
So I'm going to have two exhaust boxes down there in that area because I'm going to feed
one into there and then exhaust out and then feed the other one into the other one and exhaust out
and hopefully, as you will have seen, the two R32 tailpipes will come out the bumper.
So I have welded the two exhaust boxes together. I've made like a bracket,
hold them together with a slight gap in the middle and that's just so each end sits flush
because when it's in there, as with everything, it all needs to be squared and if one of them
boxes it over it'll annoy me and this is where we're thinking. Obviously this has got to come
up a little bit and level out but because then I can put one of the exhaust tubes into the top box
and have this come out and go to that side exhaust and I can have likewise on this one,
that one go to the bottom box, out this side and into there. With them two big boxes,
technically one per bank, it should be reasonably quiet. So what I need to do now is I need to 3D
print some kind of spacer for between there and there, maybe, I don't know, an inch or so,
so I can clamp it all so I get it all level and all square because obviously,
centre line, centre line, everything has to be parallel. So these are the 3D printed blocks
which hold the exhaust 20mm off this pipe so it sits level, it's symmetrical there and there.
With the pressure of this it's held it slightly off and the eagle eye will see the Haldex system
is back on there, I'll explain that later on. So now I think it's get it up in the air and start
at least making one of the exhaust mounts. We have one exhaust mount done. So that's
this one in the centre, horrible welding, horrible welding, that needs sorting out.
So we've got the centre mount done and bolted, now we've got these two here which now is going
to build a bracket from there to there. The more I put in, the more excited I'm getting.
And if you take these two spacers out, it holds itself perfectly where it needs to be,
it's in the centre. So now it's the task of joining basically there to there. I've just
put that in the hole, it needs to come out a bit and what have you but a bit of fettling,
bit of messing around, big problem which could technically stop us in our tracks now from
carrying on because I ordered some V-band flanges off the old eBay, should have known better,
but they are coated mild steel, not stainless, even though the hat and the flange is stainless.
Look, I thought well it's bad welding, I thought why is this all kind of going all grotty?
So that stops us now because I can't join the exhaust boxes to the downpipes
because I need these V-band flanges, headache. So it's on, it's not bad for a fiberglass copy,
it fits relatively, a bit of tweaking, this is just me slinging it on, but yeah it'll do the
job at least to marry all these up. So let's get in the air, let's see how close I am with
the exhaust outlets because that's the key. So it's the day after the disaster of the flanges
and luckily, luckily my friend had two on shelf, before, after, two proper stainless flanges
and we've got two exhaust tips. I'm not going to show you them until later in the video,
so let's now try and put some flanges on and looking at putting the tailpipes out the rear.
So I need to put the flanges in here, so I need probably them squaring up a little bit
and about a 20mm gap for the flange. So the X-pipes are welded, I'm not going to show you
just yet because it looks incredible. So what I've done now is I've finished up these two pieces,
one there and one there, so both pipes are pointing out and I've just got to put the tailpipes on
and then I can bring it down and unveil it. So all the fabrication work is done,
the big unveil, it looks incredible. Are you ready for the exhaust tips? Let's open the boot
and here we have it, now kind of back on its wheels. This is the first VW I've ever built
and I'm well chuffed with how it's turning out. So obviously this isn't my car, this is my son's,
let's get him out and let's get his reaction. I am well happy with this, I'm chuffed to bits of it.
Oh my god, that looks insane, Jesus. Look at his face, he's shocked. From this angle it's just
insane. Wow. Is that everything you want it to be? It's everything, everything and more.
So I think that gets my son's seal of approval. I'm over the moon with this, especially for 11
weeks work, we are smashing it. So put in the comments if there's a crazier build in the UK,
Mk4 Golf, please subscribe, please support and I'll see everyone on the next video.
