Need to calibrate your extruder, and calculate your e-steps? this video is all about e step calculation, and getting your extruder to extrude the proper amount of filament. this is a fail proof method for extruder calibration on the ender 3 / ender 3 pro, but can also be used to calculate the e-steps for other 3d printers as well, including the cr-10 and most other machines. watch this video to learn how to calibrate your extruder, and calculate the e steps for ender 3!
If you cant afford a donation, thats ok. leave a couple likes. and dont forget to subscribe. sharing and liking our videos is one of the best ways to help support the channel. other ways to contribute: if you shop on amazon, bookmark this link and use it, it costs you nothing, and helps me out a ton! https://www.amazon.com/?rw_useCurrent...
if you can afford a donation, please contribute! a little goes a long way! thanks again for all the support people! I couldnt do it without you!
Disclaimer: ANY AND ALL reviews are my own, honest opinion, and I do not accept payment in exchange for a favorable review. for more information on where to send your tech to be reviewed, e-mail me at [email protected] Subject:TECH
Current Channel Goal: 1000 Subs!
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
now accepting reviews! sorry we DO NOT take payment for better reviews.
AI Generated·May contain errors
All right in this episode we're going to be calibrating our e-steps and adjusting our flow
rate. In order to do that we are going to be needing another tool. So there's a website here
I put a link in the description down below. It is pronterface.com. Go ahead and click on that.
You're going to go to the downloads tab and you're going to want to download this program.
Whether you want to get the git repository, check out the latest release, or if you want to just go
with the Windows or Mac OS X binary. So once you have that installed and you get it up and running
you should see a scene like this. Now it's important to make sure you don't have Kira
open or anything else that might be trying to communicate with your printer. And you need to
have your printer plugged into the PC for this to work because we're going to be sending commands
through Pronterface. It's going to interface with the board and it's going to execute those
commands on your printer. So what you need to do is yours will probably be on COM1. If there's any
other option up here go ahead and click on it. Mine's COM4. I know that's my Ender 3 because I
had it hooked up earlier. And just hit connect. If it doesn't connect try the other port but odds are
it's whatever other port shows up that isn't COM1. All right so now you can see we're connected to
our printer. Before we can extrude anything, which is what we're going to be doing, we need to turn
our heat on. So go ahead and click here where it says set. And we will go ahead and measure our
filament for the first step of calibrating our e-steps. All right and for the next step here I'm
going to make sure I set my calipers to 100 millimeters. It's right there. Tighten it up.
Yep we're good. Okay so the next thing you need to do is get a sharpie, bring your calipers,
come over here. You're going to want to find a nice flat spot to place the depth measuring
part of your calipers up against. Pull the filament tight. Remember the location you're
placing here because you're going to measure back to that later. And then mark your filament at 100
millimeters. Now you can clearly see my mark there. So we're going to go back over to Pronterface.
All right we're back in Pronterface. You can see we're all heated up to 220 here.
And we are set to extrude 100 millimeters at 100 millimeters per minute, which means it'll take 60
seconds to extrude all this. It's going to seem like it's going really slow, but that's what we
want. We're going to see how close that mark gets to the point we measured from and then we'll do a
test to figure out what we need to do to adjust the e-steps. So go ahead and click extrude there.
Okay we're about halfway through extruding here. I need to clean my nozzle there. It's binding up a
little bit. There's our mark there. About 10 seconds left of extruding to go. And there it stops.
And again with our calipers here we're going to measure
exactly how far away that mark is. All right as you can see here we got about a 4.9 millimeter
reading. So we'll just round that up to 5. Meaning that we tried to extrude 100 millimeters of filament
and we only got 95. We're under extruding by about 5 percent. So here's where the math comes in.
All right now in order to complete the equation to figure out what we need to adjust to we need
to go in here and in Pronterface we're going to send a command to the printer. It is going to be
the m503 command. You'll see if you look in here echo steps per unit. This last number here where
it says e93 that is your current e-steps. Okay so in order to get the number we want what we're
going to do is we're going to take the number of millimeters that we wanted which is 100
and divide that by the number of millimeters we actually extruded which in our case was 95.
Then you're going to take that number times whatever you got back for your e-step.
So in this case it's going to be 93. I'm lazy so I got out my calculator here. We were going for
100 millimeters that's what we set it to extrude and we're going to divide that by
95 which is what actually came out. The answer to that is 1.05. Now we're going to take this
number and multiply it by what we got for our e-steps here which is 93. That's going to give
us 97.8947 in my case. Now we're only going to use the first four numbers of this and I'm going
to round that up or excuse me the first three numbers after the decimal and I'm going to round
the fourth one up. So our total is going to be 97.895. That's what we want to use for according
to my calculation. You're going to use whatever number you got according to your calculation. Now
we need to go back to Pronterface and we're going to have to enter a couple more commands to change
what we need to do. Let's type m92. Alright so we need to type m92. Okay this is going to set
our e-steps. We're going to set the e value and we're going to type in that number and in our
case it was 97.895. We're going to hit send and then we're going to type m if it'll let me m500.
It should say settings stored down here. You can see this.
That means it's been updated and in fact if we do m503 one more time
we can find that same number and it has changed to 97. So we are good to go on that end
and we could run the test again and see where we end up. I'm fairly certain that this is right
where I want to be because that's the same number I had before I changed it back to do this video.
That's it for this one guys. Stay tuned and we will calibrate the flow rate as well.
And as always guys I am Technivorous. Thanks for watching this video.
Don't forget to hit the like button. You can subscribe right here by clicking on the icon
and I put a couple videos up in the corner. One of them is going to be my latest video,
my latest upload and the other one is going to be what YouTube recommends for you. So
feel free to check those out. Don't forget to hit that bell for notifications down below
and we'll see you guys next time.