This is the Ultimate beginner's guide to the Ender 3! welcome to the channel! this video will show you how to read your calibration cube, to diagnose problems and fine tune your settings! if you havent watched the first videos in this series, start there! if you have found your way here, and are new to 3d printing, or just purchased your Ender 3, this is the guide for you! i suggest you watch the whole video, so you dont miss anything that might prevent panic later!
This video demonstrates how to use a calibration cube to fine-tune 3D printer settings. The instructor guides the viewer through identifying common issues like \"elephant's foot\" and under-extrusion, showing how to use calipers for measurement and adjusting flow rates and bed leveling in the slicer to achieve a dimensionally accurate print.
All right, so now we're getting into the calibration cube and first things first we need to download a cube file
So I'm using thing number one five eight six two. Oh six. I will put a link to this in the description down below
So it's loaded up as you can see. We're still using the same profile ender three point one six millimeters
Now we need to make an adjustment for our temperature and our ideal temp was
205
The build plate temperature since this is a smaller item, I don't think it's really gonna go anywhere
I'm gonna turn this down to 55
And I do that because I don't want to elephant foot the bottom layer there
I want it to be as exact as possible
And a little bit lower heat there keeps it from squishing just a little bit more
I want to make sure I don't have sports turned on and I'm gonna turn my brim off as well
So the only thing you should have changed in your ender profile so far for this print are going to be the printing temperature
and
the
build plate adhesion
so change from a brim to a skirt and
Make sure that your temperature is set in all four categories to the printing temperature that came out the best on your temperature tower
I'm gonna go ahead slice and save and send it to the printer
All right, so we have printed our calibration cube
looks like
The bottom did get a little flattened out as you can see we do have a little bit of elephant footing there
There we go a little bit of focus
But
You'll notice aside from the elephants foot we have a problem on the top
But for now, we're looking for the measurements of this cube and to do that. We need to get our calipers
Now I have a pair here that are a regular pair of mechanical calipers
If you don't know how to use these I will put a video in right here
That will show you how to take proper measurements
now
You can tell which dimension you're measuring because it'll be the dimension with the face touching your calipers. We're measuring the Z right now
Okay, and it's coming in at nineteen point
Five between nineteen point five and nineteen point six
That half a millimeter difference is most likely this elephants footing or this squish here. Okay
Both my other dimensions the X and the Y both came in at almost exactly 20 millimeters
So well with intolerance and nothing that we need to worry about changing. We will take care of this problem with the Z. However
All right. So this is the same profile. I
Changed a few things and I will show you what they are the most important of which is
What we did to take care of the gaps in the top of our model and that is going to be in the material section
We adjusted the flow and initial layer flow. Okay, so I set the flow to 120
Because I was under extruding slightly and I set the initial layer flow to 137 now
I played around with this value and that is right where my sweet spot is
If you are getting too much
Flow on the bottom layer, you might want to adjust that a little bit, but this one should be pretty well spot-on
if you don't have this menu what you need to do is click on the settings wheel and
Find it under the material tab and make sure that you check it right here and right here
So there are a ton of options in here
they don't normally show up each of these sections all you have to do is click on the little settings wheel and
You can add or subtract settings that you like to deal with or don't like to deal with so
Now that we have our flow set correctly. The other problem that we wanted to take care of was that little elephant's foot
Now you'll notice this is the next model. I'm going to be printing. This will be for the next video
We are gonna do a overhang test. Don't worry about this right now
And you'll notice that this discoloration here
When you do the overhang test, we change that infill to 100. So that's why that's like that, but don't worry about that
basically
The two settings that I've changed are the flow settings
Like I said, I was gonna come in and change the initial layer height to be a little bit higher to get rid of that
Elephant's foot, but I did do a little adjusting of my bed and print another cube and it came out way better
So sometimes the bed is just too close to the nozzle and that causes that elephant's foot
All right. So here we have our
New better calibrated cube with our new flow rates and our
Adjustments for the elephant's foot as you can see the elephant's foot has pretty much been taken care of I did measure it
The Z is pretty much exactly the same as the X and the Y now the other detail that we took care of
This was from the top flow
in that
Category that we expanded in Kira
In the material section, that's what filled these little gaps in so
Taking care of two major problems with this model. We're ready to move on to our next test print
Which is going to be an overhang test as we get into some of the more intermediate stuff
As in working on bridges and support and stuff like that in Kira. So
We're gonna do a support test next an overhang test
But for now the important thing to remember is if you're still having problems
And your cube did not come out as nice as this one. Go ahead and check out the troubleshooting guide
Another important tip if you're printing printing flat objects and you want a smooth surface there
Check out the Kira setting for ironing. We'll look into that later, but that will make that look a little bit cleaner
But like I said as you notice it did fill the gaps that we had there. So
work in progress
well on our way is
If you're having any problems with getting your profile up to this point, I do have the current profile. I have set right now
Ready to go and available for download at a link below
So go ahead and grab that before we move on
we shouldn't do any more messing with the profile or the settings other than maybe a couple of temperature adjustments here and there and
turning support on and off so
If you grab that go ahead and import it like we did in one of the last videos and you should be good to go
Let me put up a few close-up pictures of this guy real quick
First I'm going to show you a close-up of the top here
And then I will show you a close-up of the bottom as well
Now the sides all look pretty nice
Layer lines aren't too bad. There's a little bit of
There we go, you can see that residual X pattern going on in there
And we will take care of that coming up too, but that's not really a slicer thing per se so
Stay tuned for the next video guys
We'll get that mini overhang test printed and we'll see how far you can print without needing support before we go into
orienting models and putting support on them and printing things that are
Funner to print and a little bit more complicated. Thanks guys