In this video I go over how to rewire your main board fan so it doesn't shut off with the part cooling fan. The main board fan should always be running when the printer is on to prevent overheating of the board and stepper motors, but it comes attached to the same output as the part cooling fan, which is not ideal for pri ting petg or abs, as when we shut down the part cooling fan for these plastics, it shuts off the main board fan as well, and this can cause overheating. I'll show you how to rewire the fan so it's always on in this simple how to video!
The following is a list of affiliate links for ender 3 parts, and upgrades. using them helps the channel out a ton, so if you use these videos, and need to order parts, please use these links!
micro-swiss hot end: https://amzn.to/2pSQHsr light bar led upgrade: https://amzn.to/30UyPKm If you cant afford a donation, thats ok. leave a couple likes. and dont forget to subscribe. sharing and liking our videos is one of the best ways to help support the channel. other ways to contribute: if you shop on amazon, bookmark this link and use it, it costs you nothing, and helps me out a ton! https://www.amazon.com/?rw_useCurrent...
if you can afford a donation, please contribute! a little goes a long way! thanks again for all the support people! I couldnt do it without you!
Want to send me something? Technivorous 902 n Hughes Blunt Sd 57522
now accepting reviews! sorry we DO NOT take payment for better reviews.
All right, so first things first, welcome back all my Technivores! I'm Technivorous,
we are going to be getting into a little bit more difficult mod today.
It is actually not too difficult, but it will require you to open up the
case of your Ender-3 here. So, a lot of people don't realize that when you turn off the
hard cooling fan, the fan on the side of your hotend here, it also turns off the fan in your
motherboard case. That is not ideal, because it can cause overheating of the electronics,
it can cause overheating of the stepper motors if you're running too long without that fan,
and it can cause slippage and shifting layers. So, today we are going to open up our Ender-3,
we are going to disconnect the motherboard fan from where it is connected now, and connect it
to the always-on power. So basically, we're going to unwire it from the connector it's hooked into,
which is connected to this fan on the side, and we're going to wire it to the place where the
cooling fan for the hotend is on the front here. Alright, now before we get to the video,
if you're new to the channel, I wanted to let you know that we try to stay up to date on all
things 3D printing, from filament and printer reviews, to in-depth slicer analysis, as well
as a plethora of how-to videos. So, if you haven't already, make sure you hit that subscribe button
and ring the bell so you can be notified every time we post a new video. That being said,
let's jump right into it. Alright, so we got our Ender case opened up here,
and what we need to do is remove this fan. They did glue these in, so you got to be a little
careful. It doesn't matter if we rip the wires on this one, because we're going to cut the ends
anyway. But you still want to be careful not to pull anything out that's not supposed to come out.
And what we're going to do is these first two slots in this rail going vertically here,
are always on power. They run the fan for the hot end. We need to get this fan hooked up to there.
So, there is already an item inside it. Like I said, that is the hot end fan.
Not to be confused with the part cooling fan. So, we are going to grab a handy screwdriver
and get one on the right side. Alright, and we are going to loosen
these bottom two screws here. In fact, before I do that though, I'm going to bolt this back
to the case so it's not sliding around on me. You're not going to take the motherboard all
the way off. There's really no point in taking these big two screws on the B-slot rail off,
because you can get the bottom off without having to mess with that.
Now, if I can only get them to screw in without cross-threading, that would be amazing.
Let's just hold it a little more stable while I unscrew the rest here.
There it goes. Make sure it's on there good and tight so it's not going anywhere.
And we are going to loosen these two screws right here. Only slightly.
I want to be able to get the other wires in there, but I don't want my other fan wires to fall out.
So, the next step. Clippers. This is my fan CPU right here. Clipped it.
Do need to get this out of here because I don't want to cause any sort of shorts or anything.
If there's no power in, there's no power out, but the board still has power, so there's a possibility
that it can cause problems. So there we have that. Okay, now
I'm going to hook my fan into these two leads here. These always-on power at the bottom two.
I'm going to follow the convention of the fan that's already in there and insert the black
into the second hole. Maybe. It's a little bit tight, so it's tricky, but it is doable.
Okay, got it in there. Clamp my screw down on the black one before I try putting in the red one.
Nice and sturdy. You do want to make sure that these are making a good connection.
If your fan doesn't turn on, your motherboard is going to pry, and that's obviously a bad situation.
All right, so before we plug everything back in, let's take
the power cord I got here. We're going to turn it on and make sure the fan spins.
Turn it on. The fan should start, and there it goes. You can see it spinning,
and it is now on always-on power. If I turn my fan down for my part cooling fan,
it won't affect my motherboard. I won't pry anything. I won't overheat. I won't end up
with overheating stepping motors. This is one of the main causes of skipping or slipping or
shifting layers on large PETT prints. When the fan is off, the steppers tend to overheat,
and they will cause shifting, and you'll get all sorts of nasty problems. Now we're good to go. I
need to put the case and everything back on, and we are done upgrading our fan to be always-on.
All right, and there you have it. You're now ready for long prints without a part cooling fan.
You won't do any damage to your motherboard because the motherboard fan will always be on,
although I will say it does add a little bit to the noisiness of this printer. It's not too loud,
but if I were to tilt my Ender 3 back or forward a little bit so there was more exposure to the
vent on the bottom, you would see what I was talking about. It's just a slight hum or whirr,
no worse than the front-end fan on your oven. As always, this channel was brought to you by
these fine Patreon supporters. If you'd like to support the channel on Patreon,
head over to www.patreon.com slash technivorous. All right, guys, that's going to be the end of
this video. As always, thank you. I'll put a video up right here that you can check out
for more of our stuff, and if you're still here and you haven't already,
why don't you click right here and subscribe to the channel?