Hey folks, Tech Nervous here. Today we're going to be looking at how to change the filament
in this bad boy. This is an FL Sun. It is a giant delta printer and it is super fast. So
I've been having some issues with stringing and prints not sticking and that turns out because
it's not high speed filament. So I have some high speed filament that should print a lot better and
give me a little bit higher quality. Now other than the few misses I've had such as the one you
see in here now, I've gotten some great prints off of this machine and I'll show you some of
those coming up. We're going to have a few videos on this machine but for now let's go ahead and
clean up our mess here and get the machine ready and I can show you how to change out the filament.
It's not a very complicated process but there are a few steps involved and it does take a little bit
of effort. It's one of the reasons I've put off doing it for so long. However, one of the really
nice things about this printer is that up here it has its own built-in filament dryer
and as you can see right now it's full of Proto Maker and Orange PETG. So we are going to grab
some blue high speed PLA that I have and we are going to swap it out right now on the TechNiverse
channel. Okay so first things first before we can remove the filament we need to heat the nozzle up
to ensure that it actually comes out clean. So what we're going to do
is go into our settings here and we're going to change the temperature of the hot end
to, since this is PETG, we're going to do 235. 245 is the preset. We'll just go with that.
So it's going to take a while to heat and then we're going to use the filament changing settings.
Now right now the dryer is turned off and I know that you guys can't see this.
Let's go ahead and I'll grab the camera and show you what we're doing down here.
So I've selected settings and temperature slash fan and increased the nozzle temperature and I
could do it custom. What I did was just hit the PETG button. As you can see it gets hot super
fast. It's literally been about a minute since I turned it on and it is oozing a little bit
from the tip there. Now in order to change this out we're going to need to lower
the gantry here. So right now it's homed. We want to move on the Z. It says we have to home first
so we'll home first. Now we're going to go ahead and move it down. We don't need it all the way
down. What we need is this coupler here. We're going to release the coupler. We're going to
slide it up. We're going to cut the filament which will allow us to take it out of the tube
and out of the spool holder which is the filament dryer here. You can see it going down into a
bowden here. So this is actually a direct drive extruder. The reason the bowden tube is so long
is just to keep things from getting coiled up in here while the delta is running. So let's go ahead
and put this back on the stand see if I can get a better angle and we'll show you how to take this
off. So unfortunately I just loaded the filament and my camera was on slow motion. My bad. So I'm
just going to run you through this real quick here how it's done. Basically you take this coupler here
and you hold the plug down pop the plastic out then you snip it about right here right. So it's
caught in the direct drive extruder so what you'll do is you'll hit unload filament down here and
it'll force the rest of the stuff in the tube down into the extruder past the actual
why can't I think of it well it'll force it down into the nozzle past the extruder is what I'm
trying to say. So then there will be nothing here and you can slide your new filament in
through the filament holder up top through the bowden tube. Once it's sticking out like this you
just pop it in there and you hit load on the machine and it will pull it in then you simply
re-hook the coupler and you are good to go. Super simple just a little bit different than some of
the other machines where you have to hold a release on the extruder and pull it backwards.
There is no release on this it just force feeds everything past the extruder and it's such a tight
space in there that when your next filament comes in it just pushes out whatever's left. So right now
we are completely loaded and do a little test run of extruding some here
and make sure everything's working properly and as you can see it is. So I will take that
slowed down video and take the visuals for it and allow you to see the actual process.
I just wanted to make sure that I could explain what was going on as well.